XU9-FW75CDMA 1xRTT Cellular Module

FW75 and C200 CDMA 1xRTT Wireless Modules System Integration Manual Abstract This document describes the features and the integration of u-blox LISA-C200 and FW75 CDMA2000 1xRTT wireless modules. These modules are complete and cost efficient CDMA solutions offering 153 kb/s data speed dual-band 800/1900 MHz data transmission technology in compact form factors. locate, communicate, accelerate www.u-blox.com - System Integration Manual CDMA-2X-11004-P1 Page 2 of 84 Document Information Title FW75 and C200 Subtitle CDMA 1xRTT Wireless Modules Document type System Integration Manual Document number CDMA-2X-11004-P1 Document status Objective Specification Document status information Objective Specification This document contains target values. Revised and supplementary data will be published later. Advance Information This document contains data based on early testing. Revised and supplementary data will be published later. Preliminary This document contains data from product verification. Revised and supplementary data may be published later. Released This document contains the final product specification. This document applies to the following products: Name Type number Firmware version PCN / IN LISA-C200 LISA-C200-00S n.a. LISA-C200 LISA-C200-20S n.a. FW75-C200 FW-C200-00S n.a. FW75-C200 FW-C200-20S n.a. FW75 and C200 - System Integration Manual CDMA-2X-11004-P1 Objective Specification Page 3 This document and the use of any information contained therein, is subject to the acceptance of the u-blox terms and conditions. They can be downloaded from www.u-blox.com. u-blox makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. u-blox reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © 2012, u-blox AG. u-blox ® is a registered trademark of u-blox Holding AG in the EU and other countries. - System Integration Manual CDMA-2X-11004-P1 Objective Specification Preface Page 4 of 84 Preface u-blox Technical Documentation As part of our commitment to customer support, u-blox maintains an extensive volume of technical documentation for our products. In addition to our product-specific technical data sheets, the following manuals are available to assist u-blox customers in product design and development. AT Commands Manual: This document provides the description of the supported AT commands by the module to verify all implemented functionalities. System Integration Manual: This Manual provides hardware design instructions and information on how to set up production and final product tests. Application Note: document provides general design instructions and information that applies to all u-blox Wireless modules. See Section Related documents for a list of Application Notes related to your Wireless Module. How to use this Manual The System Integration Manual provides the necessary information to successfully design in and configure these u-blox wireless modules. This manual has a modular structure. It is not necessary to read it from the beginning to the end. The following symbols are used to highlight important information within the manual: An index finger points out key information pertaining to module integration and performance. A warning symbol indicates actions that could negatively impact or damage the module. Questions If you have any questions about u-blox Wireless Integration, please:  Read this manual carefully.  Contact our information service on the homepage http://www.u-blox.com  Read the questions and answers on our FAQ database on the homepage http://www.u-blox.com Technical Support Worldwide Web Our website (www.u-blox.com) is a rich pool of information. Product information, technical documents and helpful FAQ can be accessed 24h a day. By E-mail Contact the nearest of the Technical Support offices by email. Use our service pool email addresses rather than any personal email address of our staff. This makes sure that your request is processed as soon as possible. You will find the contact details at the end of the document. - System Integration Manual CDMA-2X-11004-P1 Objective Specification Preface Page 5 of 84 Helpful Information when Contacting Technical Support When contacting Technical Support please have the following information ready:  Module type (e.g. LISA-C200) and firmware version  Module configuration  Clear description of your question or the problem  A short description of the application  Your complete contact details - System Integration Manual CDMA-2X-11004-P1 Objective Specification Contents Page 6 of 84 Contents Preface ................................................................................................................................... 4 Contents .................................................................................................................................. 6 1 System description ............................................................................................................ 8 1.1 Overview ...................................................................................................................... 8 5.1 Architecture ................................................................................................................. 13 5.1.1 Functional blocks .................................................................................................... 13 5.2 Pin description ............................................................................................................. 14 5.3 Power management ....................................................................................................... 17 5.3.1 Power supply circuit overview .................................................................................... 1…

Text truncated - open the document above for the full version.

© All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com SPECIFICATION Model No. : FXP14 GPS Part No : FXP14.07.0100A Product Name : FXP14 Hepta-Band Cellular Antenna and GPS 850/900/1700/1800/1900/2100 and 1575.42 MHz Feature : IPEX MHFII Connector (U.FL compatible) 100 mm Cable 70*20*0.1 mm RoHS Compliant VERSION DATE PAGE DESCRIPTION CENTRE APPROVED A 04/07/2009 All Antenna Specifications San Diego Ruben F. Cuadras © All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com I. OVERVIEW The Taoglas FXP14 Hepta-Band Cellular Antenna with GPS covers all world-wide bands (850 / 900 / 1700 / 1800 / 1900 / 2100 and 1575.42 MHz). These cellular bands are used for different technologies in different countries such as GSM / CDMA / DCS / PCS / WCDMA / UMTS/ HSPA / GPRS / EDGE / 3G plus GPS. This antenna is ideal for use with cellular modules with Assisted GPS functionality on board where only one antenna connection is available. The antenna has been designed in a flexible material with a rectangular form-factor and cable connection for an easy installation. The antenna works on different plastics and thickness. We have selected a piece of 2 mm ABS for testing. II. ANTENNA CHARACTERISTICS Parameter Hexa Band Cellular Antenna Cellular Band (MHz) 850 900 1700 1800 1900 2100 Return Loss (dB) -7 -12 -8 -9 -9 -8 Efficiency (%) 52 55 60 60 62 65 Gain (dBi) 2 1.5 3 2.5 2 2.5 Impedance 50 Ohms VSWR ≤2.5:1 Polarization Linear Power Handled 5 W Operation Temperature -40 ºC ~ +85 ºC Storage Temperature -40 ºC ~ +85 ºC Dimensions 70 X 20 X 0.1 mm Weight 1.5 g Connector MHFII (U.FL Compatible) Cable Standard Mini-Coax 1.13 mm Cable Length and color 100 mm, Black RoHS Compliant Yes Adhesive 3M 467 Parameter GPS Antenna Frequency (MHz) 1575.42 Return Loss (dB) -7 Efficiency (%) 50% Gain (dBi) 2.2 Radiation Pattern Omni-directional properties © All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com III. TEST SET UP A Satimo SG24 3D Scan System with Anechoic Chamber. Figure 1. Satimo System. Agilent 5071C Vector Network Analyzer. Figure 2. Network Analyzer. Y X Z © All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com IV. ANTENNA PARAMETERS The next antenna parameter graphs like Return Loss were measured in the Agilent 5071C Vector Network Analyzer. The Gain, Efficiency and Radiation Patterns were measured in the reliable Satimo 3D Scan System. A. Return Loss Data Figure 3. Return Loss for the FXP14 Antenna. B. Gain Data Figure 4. Gain for the FXP14 Antenna. © All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com C. Efficiency Data Figure 5. Efficiency for the FXP14 Antenna. D. Radiation Pattern Data. Figure 6. Radiation pattern XZ Plane, Figure 1 as reference (dB). © All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com Figure 7. Radiation pattern YZ Plane, Figure 1 as reference (dB). Figure 8. Radiation pattern XY plane, Figure 1 as reference (dB). © All Rights Reserved Taoglas Limited, Unit 3 Enniscorthy Technology Centre, Enniscorthy, Co. Wexford, Ireland www.taoglas.com Figure 9. Radiation pattern for GPS at 1575.42 MHz, Figure 1 as reference. V. MECHANICAL DRAWING Figure 10. Mechanical Drawing for the FXP14 Antenna.

12626 High Bluff Drive, Suite 200 San Diego, CA 92130 February 2, 2012 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: XU9‐FW75 Authority to Act as Agent On our behalf, I appoint Alan Laudani of Nemko USA Inc., 2210 Faraday Ave, STE 150, Carlsbad, CA, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communication Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Fusion Wireless, Inc. with offices at 12626 High Bluff Drive, Suite 200, San Diego, CA 92130. This appointment is in effect until April 1, 2012.

12626 High Bluff Drive, Suite 200 San Diego, CA 92130 February 2, 2012 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Re: Request of Confidentiality for FCC ID#: XU9-FW75 Pursuant to Sections 0.457(d)(I)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: Schematics, Parts List, Operating Description, Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(I)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application.

12626 High Bluff Drive, Suite 200 San Diego, CA 92130 February 2, 2012 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Re: Statement for tuning and final stage parameters for FCC ID#: XU9-FW75 Please note: 1. The end user cannot tune or adjust output frequency or power level in any way. Frequency and power level are both controlled by software, as required by the CDMA cellular standard. 2. The voltage provided to the final PA stage is 3.85 V nominal and the maximum current drawn is 600 mA

Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S = power density P = output power G = antenna gain R = distance 22H24E Output Power29.40(dBm)26.97(dBm) Output Power871(mW)498(mW) Antenna Gain2(dBi)3(dBi) Antenna Gain1.58(numeric)2.00(numeric) Distance20(cm)20(cm) Duty Cycle:100(%)100(%) Frequency824.7(MHz)1851.25(MHz) MPE Limit General Public0.550(mW/cm^2)1.000(mW/cm^2) Power Density0.275(mW/cm^2)0.198(mW/cm^2) Margin3.01(dB)7.04(dB) 2.1091EIRP31.40(dBm)29.97(dBm) ERP29.26(dBm)27.83(dBm) ERP0.84(W)0.61(W) ERP Limit1.5(W)3(W) Margin2.50(dB)6.94(dB) 22.913ERP Limit7(W) ERP0.84(W) 24.232EIRP Limit 2(W) EIRP0.99(W) Margin9.19(dB)3.040(dB) 2 4R PG S p =

Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 CERTIFICATION TEST REPORT Applicant: Fusion Wireless, Inc. (aka U-Blox) 12626 High Bluff Drive, Suite 200 Solana Beach, CA 92130 Equipment Under Test (EUT): CDMA 1xRTT Module Model: FW75 FCC ID: XU9-FW75 IC ID: 8694A-FW75 In Accordance With: FCC Part 22, Subpart H RSS-132, Issue 2 September 2005 FCC Part 24 Subpart E RSS 133 Issue 5 February 2009 Report Number: 2012 01195598 FCC Project Number: 10219205 Nex Number: 195598 Date: Feburary 14, 2012 Total Number of Pages: 42 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-FW75 Report Number: 2012 01195598 FCC IC: 8694A-FW75 Page 2 of 42 Section1: Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC rules parts CFR47 Part 2 and 24 subpart E for the United States and RSS132 Issue 2, RSS133 Issue 5, and RSS-Gen Issue 2 for Canada. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC and IC. The assessment summary is as follows: Apparatus Assessed: CDMA 1xRTT Module Model: FW75 Serial: EFF980, EFF748, Specifications: FCC Part 22, Subpart H Industry Canada RSS-132, Issue 2, September 2005 FCC Part 2, Part 24 Subpart E RSS 133 Issue 5, February 2009 Date Received in Laboratory: January 25, 2012 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-FW75 Report Number: 2012 01195598 FCC IC: 8694A-FW75 Page 3 of 42 1.1 Report Release History REVISION DATE COMMENTS - FEBURARY 14, 2012 Prepared By: Alex Chang - FEBURARY 14, 2012 Initial Release: Alan Laudani Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. TESTED BY: Date: F EBURARY 14, 2012 Alex Chang, RF/EMC Engineer Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-FW75 Report Number: 2012 01195598 FCC IC: 8694A-FW75 Page 4 of 42 TABLE OF CONTENTS Section1: Summary of Test Results ................................................................................ 2 1.1 Report Release History ..................................................................................... 3 Section 2: Equipment Under Test ................................................................................... 5 2.1 Product Identification ........................................................................................ 5 2.2 Technical Specifications of the EUT ................................................................. 6 Section 3: Test Conditions .............................................................................................. 7 3.1 Test Environment ............................................................................................. 7 3.2 Test Equipment ................................................................................................ 7 Section 4: Observations .................................................................................................. 8 4.1 Modifications Performed During Assessment ................................................... 8 4.2 Record Of Technical Judgments ...................................................................... 8 4.3 EUT Parameters Affecting Compliance ............................................................ 8 4.4 Test Deleted ..................................................................................................... 8 4.5 Additional Observations .................................................................................... 8 Section 5: Results Summary ........................................................................................... 9 2.1 Test Result summary table ............................................................................... 9 Appendix A: Test Results .............................................................................................. 10 A1. RF Power Output ................................................................................................ 10 A2. Occupied Bandwidth ........................................................................................... 17 A3. Spurious Emissions At Antenna Terminals ......................................................... 24 A4. Field strength of Spurious Emissions .................................................................. 31 A5. Frequency Stability .............................................................................................. 36 A6. Receiver Spurious ............................................................................................... 39 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: XU9-FW75 Report Number: 2012 01195598 FCC IC: 8694A-FW75 Page 5 of 42 Section 2: Equipment Under Test 2.1 Product Identification The Equipment Under Test was identified as follows: DEVICE MANUFACTURER MODEL # SERIAL # POWER…

Text truncated - open the document above for the full version.