XV4-WMDR129NWi-Fi Dual Band Module

WMDR-129N User’s Guide Wi-Fi Dual Band module Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pa rt 15 of the FCC Rules. These limits are designed to provide reasona ble protection against harmful interference in a reside ntial installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and us ed in accordance with the instructions, may cause harmful interference to radio communications. However, ther e is no guarantee that interference will not occur in a par ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determi ned by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following me asures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV tec hnician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance co uld void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thi s device may not cause harmful interference, and (2) this device must accept any interference received, including interference t hat may cause undesired operation. For operation within 5.15~5.25GHz frequency range, it is restricted to indoor environment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. T his equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operatin g in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located wit h any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding t o Regulatory Domain change. As long as 3 conditions above are met, further tran smitter test will not be required. However, the OEM integra tor is still responsible for testing their end-product for any additional compliance requirements required with th is module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configur ations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsib le for re-evaluating the end product (including the transm itter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: XV4-WMDR129N Manual Information To the End User The OEM integrator has to be aware not to provide i nformation to the end user regarding how to install or remove this RF module in the user’s manual of the end product whic h integrates this module. The end user manual shall include all required regu latory information/warning as show in this manual. Industry Canada statement: This device complies with RSS-210 of the Industry C anada Rules. Operation is subject to the following two co nditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, inclu ding interference that may cause undesired operation. French translation: Ce dispositif est conforme à la norme CNR-210 d'Ind ustrie Canada applicable aux appareils radio exempts de li cence. Son fonctionnement est sujet aux deux conditions suivan tes: (1) le dispositif ne doit pas produire de brouillage préju diciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionneme nt indésirable. =========================================== IMPORTANT NOTE: (For mobile device use) Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. T his equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Caution: The device for the band 5150-5250 MHz is only for i ndoor usage to reduce potential for harmful interference to co- channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. French translation: NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'expositio n aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et util isé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'int érieur afin de réduire les risques de brouillage préjudici able aux systèmes de satellites mobiles utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., q…

Text truncated - open the document above for the full version.

FCC ID: XV4-WMDR129N Report No.: RF990901C29 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch February 24, 2011 Dear Application Examiner, Brickcom Corporation, It’s an Wi-Fi Dual Band Module, FCC ID: XV4-WMDR129N, would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data input; it is integrated in chip RT3572. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is APW7139QAI-TRG DEN-10 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a extend USB cable. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: XV4-WMDR129N Report No.: RF990901C29 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

Page 2 Page 3 Page 4 Page 5 Page 6

FCC ID: XV4-WMDR129N Report No.: RF990901C29 Operational Description This device is a Wi-Fi Dual Band Module, which operates in both of the 5GHz and 2.4GHz bands, the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 5Vdc from host equipment. The antennas are Dipole and PIFA antennas with UFL antenna connector. The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA990901C29 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA990901C29 MODEL NO.: WMDR-129N FCC ID: XV4-WMDR129N ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Brickcom Corporation ADDRESS: No.1 Jen Ai Rd, Hsinchu Industrial Park, Hukou, Hsinchu, Taiwan, R.O.C. 303 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. Report No.: SA990901C29 Report Format Version 4.0.0 2 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Jan. 14, 2011 Report No.: SA990901C29 Report Format Version 4.0.0 3 1. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 3. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA990901C29 Report Format Version 4.0.0 4 4. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 22.7 1.69 20 0.055 1 5180-5240 14.3 2.02 20 0.009 1 5745-5825 21.8 2.02 20 0.048 1

Report No.: RF990901C29 1 Report Format Version 4.0.0 FCC TEST REPORT (15.247) REPORT NO.: RF990901C29 MODEL NO.: WMDR-129N FCC ID: XV4-WMDR129N RECEIVED: Sep. 01, 2010 TESTED: Dec. 29, 2010 ~ Jan. 04, 2011 ISSUED: Jan. 14, 2011 APPLICANT: Brickcom Corporation ADDRESS: No.1 Jen Ai Rd, Hsinchu Industrial Park, Hukou, Hsinchu, Taiwan, R.O.C. 303 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 142 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF990901C29 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................. 5 1. CERTIFICATION........................................................................................................... 6 2. SUMMARY OF TEST RESULTS .................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY................................................................................ 7 3. GENERAL INFORMATION ........................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ............................................................................. 8 3.2 DESCRIPTION OF TEST MODES ............................................................................. 10 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ........................................................ 11 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................. 12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................ 16 3.4 DESCRIPTION OF SUPPORT UNITS ....................................................................... 16 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND)................................................. 17 4.1 RADIATED EMISSION MEASUREMENT .................................................................. 17 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................................ 17 4.1.2 TEST INSTRUMENTS................................................................................................ 18 4.1.3 TEST PROCEDURES ................................................................................................ 19 4.1.4 DEVIATION FROM TEST STANDARD....................................................................... 19 4.1.5 TEST SETUP.............................................................................................................. 20 4.1.6 EUT OPERATING CONDITIONS ............................................................................... 20 4.1.7 TEST RESULTS ......................................................................................................... 21 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................. 47 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 47 4.2.2 TEST INSTRUMENTS................................................................................................ 47 4.2.3 TEST PROCEDURES ................................................................................................ 48 4.2.4 DEVIATION FROM TEST STANDARD....................................................................... 48 4.2.5 TEST SETUP.............................................................................................................. 49 4.2.6 EUT OPERATING CONDITIONS ............................................................................... 49 4.2.7 TEST RESULTS ......................................................................................................... 50 4.3 6dB BANDWIDTH MEASUREMENT.......................................................................... 54 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ....................................................... 54 4.3.2 TEST INSTRUMENTS................................................................................................ 54 4.3.3 TEST PROCEDURE................................................................................................... 54 4.3.4 DEVIATION FROM TEST STANDARD....................................................................... 54 4.3.5 TEST SETUP.............................................................................................................. 55 4.3.6 EUT OPERATING CONDITIONS ............................................................................... 55 4.3.7 TEST RESULTS ......................................................................................................... 56 4.4 MAXIMUM OUTPUT POWER .................................................................................... 60 4.4.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT..................................... 60 4.4.2 INSTRUMENTS .......................................................................................................... 60 4.4.3 TEST PROCEDURES ................................................................................................ 60 4.4.4 DEVIATION FROM TEST STANDARD....................................................................... 61 4.4.5 TEST SETUP.............................................................................................................. 61 4.4.6 EUT OPERATING CONDITIONS ............................................................................... 61 4.4.7 TEST RESULTS…

Text truncated - open the document above for the full version.

Report No.: RF990901C29-1 1 Report Format Version 4.0.0 FCC TEST REPORT (15.407) REPORT NO.: RF990901C29-1 MODEL NO.: WMDR-129N FCC ID: XV4-WMDR129N RECEIVED: Sep. 01, 2010 TESTED: Dec. 29, 2010 ~ Jan. 04, 2011 ISSUED: Jan. 14, 2011 APPLICANT: Brickcom Corporation ADDRESS: No.1 Jen Ai Rd, Hsinchu Industrial Park, Hukou, Hsinchu, Taiwan, R.O.C. 303 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 79 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF990901C29-1 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................. 4 1. CERTIFICATION........................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY................................................................................ 6 3. GENERAL INFORMATION ........................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................................... 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................... 9 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................ 11 3.4 DESCRIPTION OF SUPPORT UNITS ....................................................................... 11 4. TEST TYPES AND RESULTS .................................................................................... 12 4.1 RADIATED EMISSION MEASUREMENT .................................................................. 12 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................................ 12 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS .............. 12 4.1.3 TEST INSTRUMENTS................................................................................................ 13 4.1.4 TEST PROCEDURES ................................................................................................ 14 4.1.5 DEVIATION FROM TEST STANDARD....................................................................... 14 4.1.6 TEST SETUP.............................................................................................................. 15 4.1.7 EUT OPERATING CONDITION.................................................................................. 15 4.1.8 TEST RESULTS ......................................................................................................... 16 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................. 34 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 34 4.2.2 TEST INSTRUMENTS................................................................................................ 34 4.2.3 TEST PROCEDURES ................................................................................................ 35 4.2.4 DEVIATION FROM TEST STANDARD....................................................................... 35 4.2.5 TEST SETUP.............................................................................................................. 36 4.2.6 EUT OPERATING CONDITIONS ............................................................................... 36 4.2.7 TEST RESULTS ......................................................................................................... 37 4.3 PEAK TRANSMIT POWER MEASUREMENT ........................................................... 41 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT ......................................... 41 4.3.2 TEST INSTRUMENTS................................................................................................ 41 4.3.3 TEST PROCEDURE................................................................................................... 42 4.3.4 DEVIATION FROM TEST STANDARD....................................................................... 42 4.3.5 TEST SETUP.............................................................................................................. 42 4.3.6 EUT OPERATING CONDITIONS ............................................................................... 42 4.3.7 TEST RESULTS ......................................................................................................... 43 4.4 PEAK POWER EXCURSION MEASUREMENT ........................................................ 47 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT...................................... 47 4.4.2 TEST INSTRUMENTS................................................................................................ 47 4.4.3 TEST PROCEDURE................................................................................................... 47 4.4.4 DEVIATION FROM TEST STANDARD....................................................................... 48 4.4.5 TEST SETUP.............................................................................................................. 48 4.4.6 EUT OPERATING CONDITIONS ..............................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Test Mode A 2 Test Mode B 3 4 5 RADIATED EMISSION TEST Test Mode A 6 Test Mode B 7 8