XXNTMS100Motion Sensor

#202 Itplex, YusungGu, JangDong 59-2, Daejeon City, Korea 305-343 TEL : +82-42-360-2020 FAX : +82-360-2010 email : [email protected] www.teltron.com 1 Telecommunications & Electronics X-Band Motion Sensor Model : TMS100 [ Applications ] ƒIntrusion alarm ƒAutomatic door ƒObstruction alarm system 장애물경보시스템 ƒNon-contact measurement ƒDual motion sensor with PIR ƒVelocity measurement ƒAutomatic on and off lamps [ Features ] TMS100 is X-band Doppler motion sensor to detect motion. It consists of DR(dielectric resonator) oscillator, passive diode and patch antennas and provides most reliable solution in motion detection. Average Current Duty Cycle Pulse Width Size Storage temp. Operating temp. 3dB Antenna Beam Width - Elevation 3dB Antenna Beam Width - Azimuth Received Signal Noise Settling time Current Consumption Power Supply Output Power (EIRP) Frequency +70-30 o C+55-20 mm 2 45 x 40 @5% dutymA2 %1 μS 5 Pulse Operation o 36 o 81 maxmVp-p20 3~80 Hz μVrms 10 μS 6 CWmA6030 V5.2554.75 dBm15 Over Temp.MHz 10,525 ±12.5 CW ConditionUnitMax.Typ.Min.Parameters [Electrical Specifications] Warning : The specifications can be changed without any notice. www.teltron.com 2 Telecommunications & Electronics X-Band Motion Sensor Model : TMS100 [Dimension ] [ Pin Description ] 접지GND4 접지GND3 출력IF2 전원, +5VVDD1 설명핀이름# f d c e [ Application Circuit Example ] 옆 전면 [ Block Diagram ] Tx Osc. Mixer Rx IF TMS100 #202 Itplex, YusungGu, JangDong 59-2, Daejeon City, Korea 305-343 TEL : +82-42-360-2020 FAX : +82-42-360-2010 email : [email protected] (mm) Warning : TMS100 is very sensitive to ESD, so you should be very careful in installation. Unless, there would be an operational problem or it may be out of order.

FCC Confidential Authorization December 7, 2009 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: XXNTMS100 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Teltron, Inc. hereby requests long-term confidential treatment of information accompanying this application as outlined below: xBlock Diagram xSchematics xOperation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Choong Hwan Kim/ Manager 82-42-360-2020 #202 ITPlex, 16 Sinseong-Ro, Yusong-Gu, Daejeon, South Korea

Modular Approval Letter Date: March 10, 2010 The Device, XXNTMS100:, is seeking FCC authorization as a modular transmitter. The EUT meets the requirement for modular approval as detailed in FCC Public Notice DA 00-1407. Compliance to each of the requirements is described below: 1. The modular transmitter must have its own RF shielding. - The radio portion of the motion sensor module has its own RF shielding. The shielding is installed at the factory. 2. The modular transmitter must have buffered modulation/data inputs. – Please see schematics of the module. 3. The modular transmitter must have its own power supply regulator. – The EUT has its own voltage regulation circuitry. Please see schematics of the module. 4. The modular transmitter must comply with the antenna requirement of section 15.203 and 15.204(c). – The EUT meets the FCC antenna requirements. 5. The modular transmitter must be tested in a stand-alone configuration. – The EUT was tested in a stand-alone configuration. 6. The modular transmitter must be labeled with its own FCC ID number. – The EUT is labeled with its own FCC ID number. 7. The modular transmitter must comply with any specific rule or operating requirements and the manufacturer must provide adequate instruction along with the module to explain any such requirements. – The EUT is complaint with all applicable FCC rules. 8. The modular transmitter must comply with any applicable RF exposure requirements. – The EUT fully complies with RF exposure requirements. Sincerely, Choong Hwan Kim/ Manager 82-42-360-2020 #202 ITPlex, 16 Sinseong-Ro, Yusong-Gu, Daejeon, South Korea

Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 27 of 28 FCC Part15.245 Test Report 10 EXHIBIT C - EUT PHOTOGRAPHS 10.1 EUT – Top View 10.2 EUT – Bottom View

Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 19 of 28 FCC Part15.245 Test Report 8 EXHIBIT A – FCC EQUIPMENT LABELING REQUIREMENTS 8.1 FCC ID Label Requirement As Per FCC § 2.925, (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID: XXX123, where : XXX—Grantee Code 123—Equipment Product Code As Per FCC § 15.19 (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. (5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 8.2 FCC ID Label Content 8.3 Suggested FCC Label Location Label here

Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 28 of 28 FCC Part15.245 Test Report 10.3 EUT – Top View (Without Shielding) * ***** END OF REPORT *****

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 15.245 TEST AND MEASUREMENT REPORT For Teltron, Inc. #202 Itplex, 16 Sinseong-Ro, Yusong-Gu, Daejeon, South Korea FCC ID: XXNTMS100 Model: TMS100 Report Type: Original Report Product Type: Motion Sensor Test Engineer: Dennis Huang Report Number: R0911232-245 Report Date: 2009-12-02 Reviewed By: Boni Baniqued EMC/RF Supervisor Prepared By: (25) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Avenue, Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732-9164 Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 2 of 28 FCC Part15.245 Test Report TABLE OF CONTENTS 1 GENERAL INFORMATION ..............................................................................................................................5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................5 1.2 EUT MECHANICAL DESCRIPTION...................................................................................................................5 1.3 EUT PHOTO....................................................................................................................................................5 1.4 OBJECTIVE......................................................................................................................................................5 1.5 RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................6 1.6 TEST METHODOLOGY.....................................................................................................................................6 1.7 MEASUREMENT UNCERTAINTY.......................................................................................................................6 1.8 TEST FACILITY................................................................................................................................................6 2 SYSTEM TEST CONFIGURATION .................................................................................................................7 2.1 JUSTIFICATION................................................................................................................................................7 2.2 EUT EXERCISE SOFTWARE.............................................................................................................................7 2.3 SPECIAL ACCESSORIES....................................................................................................................................7 2.4 EQUIPMENT MODIFICATIONS..........................................................................................................................7 2.5 LOCAL SUPPORT EQUIPMENT..........................................................................................................................7 2.6 EUT INTERNAL CONFIGURATION AND DETAILS.............................................................................................7 2.7 INTERFACE PORTS AND CABLING....................................................................................................................7 3 SUMMARY OF TEST RESULTS......................................................................................................................8 4 FCC §15.203 - ANTENNA REQUIREMENT ....................................................................................................9 4.1 APPLICABLE STANDARD.................................................................................................................................9 4.2 ANTENNA CONNECTOR CONSTRUCTION.........................................................................................................9 5 FCC §15.207– CONDUCTED EMISSIONS.....................................................................................................10 6 FCC §15.245 (B) – FIELD STRENGTH OF FUNDAMENTAL ....................................................................11 6.1 APPLICABLE STANDARDS..............................................................................................................................11 6.2 TEST SETUP..................................................................................................................................................11 6.3 TEST ENVIRONMENTAL CONDITIONS............................................................................................................11 6.4 TEST EQUIPMENT LIST AND DETAILS............................................................................................................11 6.5 TEST PROCEDURE.........................................................................................................................................12 6.6 CORRECTED AMPLITUDE & MARGIN CALCULATION....................................................................................12 6.7 SUMMARY OF TEST RESULTS........................................................................................................................12 6.8 TEST RESULTS..............................................................................................................................................12 7 FCC §15.245 (B) – FIELD STRENGTH OF HARMONICS & OUT OF BAND EMISSIONS ..................13 7.1 APPLICABLE STANDARDS.............................................................................................................................13 7.2 TEST SETUP..............................…

Text truncated - open the document above for the full version.

Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 20 of 28 FCC Part15.245 Test Report 9 EXHIBIT B – EUT Setup Photographs 9.1 30 MHz – 1 GHz Radiated Emissions – Front View 9.2 30 MHz – 1 GHz Radiated Emissions – Back View Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 21 of 28 FCC Part15.245 Test Report 9.3 1 GHz to 18 GHz Radiated Emissions - Front View 9.4 1 GHz to 18 GHz Radiated Emissions - Rear View Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 22 of 28 FCC Part15.245 Test Report 9.5 18 GHz to 26.5 GHz Radiated Emissions - Front View 9.6 18 GHz to 26.5 GHz Radiated Emissions – Rear View Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 23 of 28 FCC Part15.245 Test Report 9.7 26.5 GHz to 40 GHz Radiated Emissions – Front View 9.8 26.5 GHz to 40 GHz Radiated Emissions - Rear View Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 24 of 28 FCC Part15.245 Test Report 9.9 40 GHz to 60 GHz Radiated Emissions - Front View 9.10 40 GHz to 60 GHz Radiated Emissions - Rear View Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 25 of 28 FCC Part15.245 Test Report 9.11 60 GHz to 90 GHz Radiated Emissions - Front View 9.12 60 GHz to 90 GHz Radiated Emissions - Rear View Teltron Inc. FCC ID: XXNTMS100 Report Number: R0911232-245 Page 26 of 28 FCC Part15.245 Test Report 9.13 90 GHz to 120 GHz Radiated Emissions - Front View 9.14 90 GHz to 120 GHz Radiated Emissions - Rear View