Y6FELE1908ECO Safe Charge Remote Control Unit

USER INSTRUCTIONS ECO SAFE CHARGE™ REMOTE CONTROL UNIT MODEL NO.: ELE1908 Transmission Radio Frequency: 433.92 MHz Transmission Range: 30 meters in open air Battery: 1 x CR2032 3.0 Vdc Conforms to FCC, EMC and R&TTE Directives FCC ID: Y6FELE1908 www.lockncharge.com This is a remote controller that can generate radio wave carrying control signal. After paired with a suitable Receiver, the remote controller can control the Receiver by pressing on the remote. Each button of the remote contains one unique code. The paired Receiver is capable to identify the code and then take action accordingly. Introduction: * Line of sight from the Remote Control Unit to the Receiver is not required. The control signal can pass through walls and ceilings. * As with all RF transmitter devices, electrical fields, metal doors, and motor devices can decrease the strength of the transmitting signal. Reorient the Remote Control Unit may increase the control range. * It is not guaranteed that every control signal sent out by the Remote Control Unit will be received by the paired Receiver. Check to make sure of the Receiver has responded after your press on the Remote Control Unit. * If the LED indicator of the Remote Control Unit dimmed, replace the battery according to the polarity sign on the battery apartment. One new CR2032 lithium battery is needed. Tips of using the Remote Control Unit: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and ( 2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the use's authority to operate the device. Important Safeguards: www.lockncharge.com

PC Locs Pty Ltd Date: 13.02.2014 Authority to Act as an Agent We declare that the following representative (agent) Name Mark Zhu Position Manager Company Name Shenzhen Certification Technology Service Co., Ltd. Address 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2 nd Road, Bao’an District, Shenzhen 518126, P.R. China Tel / Fax 0755-86375541/0755-26736857 Email [email protected] to act on our behalf on all matters concerning the application and documents submitted to PHOENIX TEST-LAB for product certification below Product Name ECO Safe Charge Remote Control Unit Model Name ELE1908 Brand Name LocknCharge . Yours sincerely, Signatory Name David Shawcross Position Innovations Manager Company Name PC Locs Pty Ltd Address 187 Mulgul Road, Malaga Western Australia 6090,Australia Tel +61-1300 725 627 Fax +61 8 9249 8415 Email [email protected] In case of FCC, we certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance.

PC Locs Pty Ltd Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Confidentiality Company name: PC Locs Pty Ltd FCC ID : Y6FELE1908 FCC Part 15 Certification Gentlemen, Pursuant to 47 CFR 0.457(d)(1)(ii) and 0.459 we hereby requests permanent confidentiality of the following documents for the subject application: Exhibit Type Description ☒ Schematics All circuitry of devices and component values ☒ Block Diagrams Details of device showing the frequency of all oscillators ☒ Operational Description Description of the circuit functions Note: Exhibit types that are commonly held confidential are: (1) Schematics, (2) Block Diagrams, (3) Bill Of Materials, (4) Operational Descriptions. Any exhibit NOT granted confidentiality is viewable on the FCC website as soon as a grant is issued. These documents contain detailed system and equipment description and related information about the product which we considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, we consider that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours sincerely, Signatory Name David Shawcross Position Innovations Manager Company Name PC Locs Pty Ltd Address 187 Mulgul Road, Malaga Western Australia 6090,Australia Tel +61-1300 725 627 Fax +61 8 9249 8415 Email [email protected] Date 13.02.2014

10mm 5mm FCC ID: Y6FELE1908

Label Location

ANTENNA

Shenzhen Certification Technology Service Co., Ltd 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2nd Road, Bao'an District, Shenzhen 518126, P.R. China. FCC ID: Y6FELE1908 Page 1 of 30 TEST REPORT FCC ID: Y6FELE1908 Applicant : PC Locs Pty Ltd Address : 187 Mulgul Road, Malaga Western Australia 6090, Australia Equipment under Test (EUT): Name : ECO Safe Charge Remote Control Unit Model : ELE1908 Standards : FCC PART 15, SUBPART C : 2013 (Section 15.231) Report No. : ST-TCB140121001 Date of Test : February 07-09, 2014 Date of Issue : February 10, 2014 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above Authorized Signature (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Certification Technology Service Co., Ltd. Or test done by Shenzhen Certification Technology Service Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Certification Technology Service Co., Ltd. Approvals in writing. Report No.: ST-TCB140121001 FCC ID: Y6FELE1908 Page 2 of 30 TABLE OF CONTENT Description Page 1 General Information------------------------------------------------------------------------------------3 1.1 Description of Device (EUT)---------------------------------------------------------------------3 1.2 Description of Test Facility-----------------------------------------------------------------------3 2 EMC Equipment List-----------------------------------------------------------------------------------4 3 Test Procedure------------------------------------------------------------------------------------------5 4 Summary of Measurement---------------------------------------------------------------------------6 4.1 Summary of test result-----------------------------------------------------------------------------6 4.2 Block Diagram--------------------------------------------------------------------------------------6 4.3 Assistant equipment used for test----------------------------------------------------------------6 4.4 Test Conditions-------------------------------------------------------------------------------------7 4.5 Measurement Uncertainty (95% confidence levels, k=2)-------------------------------------7 5 Radiation Emission------------------------------------------------------------------------------------8 5.1 Radiation Emission Limits(15.209&231)-------------------------------------------------------8 5.2 Test Setup--------------------------------------------------------------------------------------------8 5.3 Test Procedure-------------------------------------------------------------------------------------10 5.4 Test Equipment Setting For emission test.-----------------------------------------------------11 5.5 Test Condition-------------------------------------------------------------------------------------11 5.6 Test Result------------------------------------------------------------------------------------------11 6 POWER LINE CONDUCTED EMISSION-------------------------------------------------------17 6.1 Conducted Emission Limits(15.209)-----------------------------------------------------------17 6.2 Test Setup-------------------------------------------------------------------------------------------17 6.3 Test Procedure-------------------------------------------------------------------------------------18 6.4 Test Results-----------------------------------------------------------------------------------------18 7 Occupied bandwidth---------------------------------------------------------------------------------19 7.1 Test limit--------------------------------------------------------------------------------------------19 7.2 Method of measurement--------------------------------------------------------------------------19 7.3 Test Setup-------------------------------------------------------------------------------------------19 7.4 Test Results-----------------------------------------------------------------------------------------19 8 Transmission time------------------------------------------------------------------------------------21 8.1 Test limit--------------------------------------------------------------------------------------------21 8.2 Method of measurement--------------------------------------------------------------------------21 8.3 Test Setup-------------------------------------------------------------------------------------------21 8.4 Test Results-----------------------------------------------------------------------------------------21 9 Band Edge Check-------------------------------------------------------------------------------------23 9.1 Test limit--------------------------------------------------------------------------------------------23 9.2 Test Procedure-------------------------------------------------------------------------------------23 9.3 Test Setup-------------------------------------------------------------------------------------------23 9.4 Test Result------------------------------------------------------------------------------------------23 10 Antenna Requirement-------------------------------------------------------------------------------24 10.1 Standard Requirement----------------------------------------------------------------------------24 10.2 Antenna Connected Construction---------------------------------------------------------------24 10.3 Result------------------------------------------------------------------------------------------------24 11 Photographs of Test Setup------------------------------------------------------------------------25 12 Photographs of EUT-------…

Text truncated - open the document above for the full version.

Radiated Emission Test Setup in Chamber