Y6MNCOM7Motorcycle helmet communication system with BT transceiver

BX4 Firmware Version: 3.1x EN USER INSTRUCTIONS AND SAFETY Congratulations on your purchase of an N-Com product. N-Com BX4 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about BX4, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.it REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: BX4 The Bluetooth system complies with the main safety requirements and other applicable provisions of Directive 99/5/CE, Directive 2002/95/CE, Directive 2002/96/CE Battery charger Directive 2006/95, 2004/108, 2002/95/CE, 2002/96/CE, 2009/125/CE Battery Directive 2006/66 The Declarations of Compliance can be downloaded from the website www.n- com.it (Download section). FccID: XXXXXXXXX XXXXX Bluetooth is a registered trademark property of Bluetooth SIG, Inc. Bx4 3 FOR USA MARKET ONLY: SPECIAL WARNING This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna  Increase the separation between the equipment or devices  Connect the equipment to an outlet other than the receiver’s  Consult a dealer or an experienced radio/TV technician for assistance FccID: XXXXXXXXX XXXXX Bluetooth is a registered trademark property of Bluetooth SIG, Inc. 4 Contents 1. WARNINGS AND SAFETY......................................................5 1.1.Road safety..........................................................................5 1.2.Switching on the system in safe environments...........................5 1.3.Interferences.......................................................................5 1.4.Appropriate use....................................................................5 1.5.Qualified personnel...............................................................6 1.6.Accessories and batteries.......................................................6 1.7.Disposal..............................................................................7 2. CONTENT OF THE PACKAGING..............................................7 3. INSTALLATION....................................................................8 3.1.Preliminary operations – Jet helmets or Flip-up helmets...............8 3.2.Preliminary operations – Full-face helmets................................8 3.3.Installing the microphone – jet helmets or flip-up helmets...........9 3.4.Installing the microphone – full-face helmets............................10 3.5.Inserimento batteria e altoparlante destro................................10 3.6.Posizionamento dell’e-box.....................................................12 3.7.Installing the adhesive keyboard............................................12 4. REMOVING THE SYSTEM.....................................................13 5. BASIC FUNCTIONS.............................................................13 5.1.System menu......................................................................14 6. N-COM WIZARD.................................................................14 7. PAIRING UP BLUETOOTH DEVICES.....................................15 7.1.Affiliation reset function........................................................15 8. MOBILE PHONE FUNCTIONS...............................................16 9. GPS SATELLITE NAVIGATOR FUNCTIONS............................16 10. STEREO FM RADIO.............................................................16 11. BLUETOOTH A2DP MUSIC PLAYER......................................17 12. AUDIO DEVICES WITH CABLE CONNECTION.......................17 13. RIDER-PASSENGER INTERCOM MODE.................................18 13.1.Intercom affiliation.............................................................18 13.2.Intercom function...............................................................18 14. BIKE-TO-BIKE INTERCOM..................................................18 14.1.Bike-to-Bike pair up............................................................18 14.2.Making a Bike-to-Bike call....................................................19 14.3.Taking a Bike-to-Bike call....................................................19 15. BATTERY...........................................................................20 15.1.Battery discharged signal.....................................................20 15.2.Recharging the system........................................................20 16. SUMMARY TABLE OF CONTROLS..................................…

Text truncated - open the document above for the full version.

FOR USA AND CANADA MARKET ONLY SPECIAL WARNING -------------------------------------------------------------------------- POUR LE MARCHE US et CANADIEN UNIQUEMENT MISE EN GARDE SPECIALE -------------------------------------------------------------------------- SÓLO PARA EL MERCADO USA y CANADÁ ADVERTENCIAS IMPORTANTES 2 FOR USA AND CANADA MARKET ONLY: SPECIAL WARNING This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna  Increase the separation between the equipment or devices  Connect the equipment to an outlet other than the receiver’s  Consult a dealer or an experienced radio/TV technician for assistance This model meets the government’s requirements for exposure to radio waves. Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. The highest SAR value for this model device when tested for use at the ear is 0.099 W/kg. For Canada market only: This EUT is compliant with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528. FccID: Y6MNCOM7 21550 Bluetooth is a registered trademark property of Bluetooth SIG, Inc. 3 FOR USA AND CANADA MARKET ONLY: LIMITED WARRANTY Limited warranty certificate valid for 2 (two) years from the date of purchase. Dear Customer, Thank you for choosing a Nolangroup N -Com™ device. PLEASE READ CAREFULLY ALL THE CLAUSES AND CONDITIONS OF THIS LIMITED WARRANTY CERTIFICATE. By this LIMITED WARRANTY CERTIFICATE, Nolangroup guarantee to the original purchaser of the N-com™ that the product is free from all material and manufacturing defects at the time of purchase. COVER PROVIDED BY THE WARRANTY If any defect covered by this limited warranty certificate comes to light within 2 (two) years from the date of purchase, Nolangroup shall proceed, through their distribution networks and after verifying the defect, to repair or replace the defective product. Nolangroup shall supply all the materials and provide all the labor reasonably necessary to remedy the reported defect, except for cases in which the damage is attributable to one of the reasons listed in the paragraph below, entitled “Exclusions and limitations of cover”. EXCLUSIONS AND LIMITATIONS OF COVER This warranty covers only material and manufacturing defects. Nolangroup cannot be held liable for damages to the product which are either wholly or partially attributable to any other cause, including, but not limited to: a) damage caused by improper use, lack of due care, normal wear and tear of internal and external components; b) scratches, abrasions, or other damage caused to the external parts of the N-com™ by accidental impacts; c) damage caused by the application of stickers and/or adhesives; d) any damage caused by an accident; e) any modification or change made to the device by the user or by third parties; fl) use of incompatible accessories not sold by Nolangroup. Defects covered by this warranty likewise do not include all the specific and subjective situations which may arise during dynamic use of the N-Com™ equipped helmet, such as problems of comfort due to improper sizing, or wind noise while riding. Nolangroup cannot in any case be held liable for accidental or consequential damage (including, with no limitation whatsoever, injuries to a person or persons) resulting from the failure to comply with the obligations stipulated in this warranty regarding Nolangroup products. Some states do not allow the exclusion or limitation of implied warranties, incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state VALIDITY OF THIS LIMITED WARRANTY This warranty is valid only if all the sections of the attached REGISTRATION FORM are completed in full and the registration is returned to the address indicated on the card within 10 (ten) days from the date of purchase: 1) Identification code (Fig. 1-2-3); 2) Name of the authorized dealer; 3) Date of purchase of the N-Com TM; 4) Name, address and telephone number of the purchaser. 4 Fig. 1 - Option A Fig. 2 - Option B Fig. 3 - Option C PROCEDURE TO BE FOLLOWED TO MAKE POSSIBLE CLAIMS To proceed with any claim covered by this warranty, the purchaser must notify directly Nolan’s agent in the USA of…

Text truncated - open the document above for the full version.

Firmware Version: 3.1x EN USER INSTRUCTIONS AND SAFETY Congratulations on your purchase of an N-Com product. N-Com B X 4 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B X 4, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.it REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: B X 4 The Bluetooth system complies with the main safety requirements and other applicable provisions of Directive 99/5/CE, Directive 2002/95/CE, Directive 2002/96/CE Battery charger Directive 2006/95, 2004/108, 2002/95/CE, 2002/96/CE, 2009/125/CE Battery Directive 2006/66 The Declarations of Compliance can be downloaded from the website www.n- com.it (Download section). FccID: XXXXXXXXX XXXXX Bluetooth is a registered trademark property of Bluetooth SIG, Inc. B x 4 3 FOR USA MARKET ONLY: SPECIAL WARNING This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment or devices Connect the equipment to an outlet other than the receivers Consult a dealer or an experienced radio/TV technician for assistance FccID: XXXXXXXXX XXXXX Bluetooth is a registered trademark property of Bluetooth SIG, Inc.

Nolangroup S.p.a. Via G.Terzi di Sant’Agata,2 24030 Brembate di Sopra (BG) Italy Commercial Power of Attorney Ron Angel Wholesale Pty Ltd Ph 03 9464 3366 33 Macquarie Dve THOMASTOWN VIC 3074 Australia Commercial Power of Attorney for the type approval / registration of the N-Com BX4 in several countries. The company 7 layers AG, 40880 Ratingen, Germany, has been contracted by Redox s.r.l. to obtain „Radio Type Approval“ for the following electronic components: N-Com BX4 7 layers is authorized to make use of all test reports, issued by 7 layers and/or test reports issued by other national and international laboratories, for the purpose of the type approval process for the product listed above. Unless future correspondence from Redox s.r.l. directs otherwise, please extend your full cooperation to 7 layers regarding matters to the above mentioned products for the period beginning 01/10/2012 through 01/12/2012. Thank you. _____ Grant Sammut - national manager _____ (Name and function of person signing) __Thomastown_____ , ___16/10/12____ , _______________________ (place) (date) (signature)

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: Nolangroup s.p.a. Address : via Terzi di S.Agata 2 City: 24030 Brembate di sopra Country: Italy To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: Y6MNCOM7 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: This information should never get into the possession of competitors, which would be harmful for our business. Planned Release Date STC: 180 days (notes 2, 3, 4, 5) Date: 19 Oct. 12 Name and signature of applicant: Patrick Lomax Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

N-Com BX4 – Label - Labels on the product Located on the external surface of the plastic Box containing the Bluetooth PCB. Labels on the packaging Located on the external pack of the Bluetooth device Labels on the instruction leaflet See page no.3

Final Report on BX4 FCC ID: Y6MNCOM7 MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B Report Reference: October 11, 2012 Date: Test Laboratory: 7Layers AG Borsigstr. 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7Layers AG Aufsichtsratsvorsitzender Registergericht registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Ralf Mertens USt-IdNr  VAT No.: Phone: +49 (0) 2102 749 0 Vorstand Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. H.-J. Meckelburg TAX No. 147/5869/0385 www.7Layers.com Reference: MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B 2.2 Detailed Description of OUT Samples Sample : CA01 OUT Identifier BX4 Sample Description NCOM BX4 Serial No. #1 HW Status 1.00 SW Status 3.12 Parameter List: ValueParameter Description Parameter for Scope FCC_v2 Antenna Gain 0 (dBi) Frequency_high 2480 (MHz) Frequency_low 2402 (MHz) Frequency_mid 2441 (MHz) Sample : ACDC01 OUT Identifier ACDC Adaptor (AK00G-0500040VU) Sample Description AK00G-0500040VU Serial No. #1 2.3 OUT Features Features for OUT: BX4 Allowed ValuesDesignationDescriptionSupported Value(s) Features for scope: FCC_v2 AC The OUT is powered by or connected to AC Mains BT EUT supports Bluetooth data rate of 1 Mbps with GFSK modulation in the band 2400 MHz - 2483.5 MHz EDR2 EUT supports Bluetooth using data rate of 2 Mbps with PI/4 DQPSK modulation in the band 2400 MHz - 2483.5 MHz EDR3 EUT supports Bluetooth using data rate of 3 Mbps with 8DPSK modulation in the band 2400 MHz - 2483.5 MHz Iant Integral Antenna: permanent fixed antenna, which may be built-in, designed as an indispensable part of the equipment TantC temporary antenna connector, which may be only built-in for testing, designed as an example part of the equipment Page 4 of 24 Reference: MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B 2.4 Auxiliary Equipment AE No.Serial No.SW StatusHW StatusDescriptionType Designation AE 01USB Cable AE 06 Cherry RS 6000 USB ON G 0000273 2P28Keyboard 1 AE 02LG L1740BQ509WANF1W607TFT 1 AE 05Logitech M-BB48LZC90505478Mouse AE 04 Toshiba PA3378E- 3AC3 AC Adapter 1 AE 03Toshiba TECRA M9TECRA M987060248H Laptop 1 2.5 Operating Mode(s) Ref.-No.Description 01Windows computer using a Redox program to continuously transmit data via USB. 2.6 Setups used for Testing For each setup a relation is given to determine if and which samples and auxiliary equipment is used. The left side list all OUT samples and the right side lists all auxiliary equipment for the given setup. Sample No.Sample DescriptionAE No.AE Description Setup No. List of OUT samplesList of auxiliary equipment ACDC_CA01 (BX4) ACDC01AK00G-0500040VU Sample: CA01NCOM BX4 Sample: PC_CA01 (BX4) AE 01USB CableCA01NCOM BX4 Sample: AE 06Keyboard 1 AE 02TFT 1 AE 05Mouse AE 04AC Adapter 1 AE 03Laptop 1 Page 5 of 24 Reference: MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B 3 Results 3.1 General Available at the test laboratory. The results of the inspection are described on the following pages, where 'Conformity' or 'Passed' means that the certification criteria were verified and that the tested device is conform to the applied standard. In cases where 'Declaration' is printed, the required documents are available in the manufacturers product documentation. In cases where 'not applicable' is printed, the test case requirements are not relevant to the specific equipment implementation. Documentation of tested devices: Interpretation of the test results: The laboratory environmental conditions are recorded and available in the Interlab system for each performed test. Note: 3.2 List of the Applicable Body (Body for Scope: FCC_v2) DesignationDescription Part 15, Subpart B - Unintentional Radiators FCC47CFRChIPART15bRADIO FREQUENCY DEVICES 3.3 List of Test Specification Test Specification: FCC part 2 and 15 Version10-1-11 Edition Title:PART 2 - GENERAL RULES AND REGULATIONS PART 15 - RADIO FREQUENCY DEVICES Page 6 of 24 Reference: MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B 3.4 Summary Test Case Identifier / Name SetupDate of TestResultTest (condition)Ref. Lab 15b.1 Conducted Emissions (AC Power Line) §15.107 15b.1; Mode = transmit2012/09/14PC_CA01Lab 1Passed operating mode: 01 2012/08/09ACDC_CA01Lab 1Passed 15b.2 Spurious Radiated Emissions §15.109 15b.2; Mode = transmit2012/09/14PC_CA01Lab 2Passed operating mode: 01 2012/08/09ACDC_CA01Lab 2Passed Page 7 of 24 Reference: MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B 3.5 Detailed Results 3.5.1 15b.1 Conducted Emissions (AC Power Line) §15.107 Test1: 15b.1; Mode = transmit Result: Passed Setup No.: ACDC_CA01 Date of Test: 2012/08/09 7:15 Body: FCC47CFRChIPART15bRADIO FREQUENCY DEVICES Test Specification: FCC part 2 and 15 Page 8 of 24 Reference: MDE_REDOX_1202_FCCf According to: FCC 47 CFR Ch.1 Part 15 Subpart B Detailed Results: AC MAINS CONDUCTED EUT: (UH050ca01) Manufacturer: Redox Operating Condition: charging via ACDC(USB) charger Test Site: 7 layers Ratingen Operator: Giz Test Specification: ANSI C63.4; FCC 15.107 / 15.207 Comment: Start of Test: 10.08.2012 / 10:53:44 SCAN TABLE: "FCC Voltage" Short Description: FCC Voltage Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kHz 30.0 MHz 5.0 kHz MaxPeak 20.0 ms 9 kHz ESH3-Z5 Average 0 10 20 30 40 50 60 70 80 Level [dBμV] 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] MES Red_1202_005_pre PK MES Red_1202_005_pre AV LIM FCC 15b QP volt Voltage QP Limit LIM FCC 15b AV volt Voltage QP Limit Test2: 15b.1; Mode = transmit Result: Passed Setup No.: PC_CA01 Date of Test: 2012/09/14 8:53 Body: FCC47CFRChIPART15bRADIO FREQUENCY DEVICES Test Specification: FCC part 2 and 15 Page 9 of 24 Reference: MDE_REDOX_1202_FC…

Text truncated - open the document above for the full version.

7Layers AG Aufsichtsratsvorsitzender Registergericht registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Markus Becker USt-IdNr  VAT No.: Phone: +49 (0) 2102 749 0 Vorstand Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. H.-J. Meckelburg TAX No. 147/5869/0385 www.7Layers.com InterLab  is a registered trademark of 7 layers AG Photo Report – Test Setup Photos Bluetooth transceiver Bx4 Report Reference: MDE_REDOX_1201_FCC_Photo This report contains the setup photos for the reports referenced be MDE_REDOX_1202_FCCC (Part 15c) and MDE_REDOX_1202_FCCf (Part 15b) Test Laboratory: 7 layers AG Borsigstrasse 11 40880 Ratingen Germany email: [email protected] DGA-PL-192/99-02 Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. Test report Reference: MDE_REDOX_1201_FCC_Photo Page 2 of 6 1 Photo Report 1.1 Photos of test setups Photo 1: Test setup for radiated measurements (Enclosure, below 30 MHz) Test report Reference: MDE_REDOX_1201_FCC_Photo Page 3 of 6 Photo 2: Test setup for radiated measurements (Enclosure, 30 MHz to 1 GHz), intentional transmission Test report Reference: MDE_REDOX_1201_FCC_Photo Page 4 of 6 Photo 3: Test setup for radiated measurements (Enclosure, above 1 GHz) Test report Reference: MDE_REDOX_1201_FCC_Photo Page 5 of 6 Photo 5: Test setup for conducted measurements (AC Port (power line)), unintentional transmission, EUT + computer peripheral setup Test report Reference: MDE_REDOX_1201_FCC_Photo Page 6 of 6 Photo 7: Test setup for radiated measurements (Enclosure, 30 MHz to 1 GHz), unintentional transmission, EUT + computer peripheral setup