YEY-V3-1005AVisage Touchscreen Display

VDU User Manual 1074 North Orange Avenue Sarasota, Florida, 34236 1 888 575 2901 www.gpsindustries.com FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet équipement a été testé et jugé conforme aux limites d’un appareil numérique de classe A, conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nocives lorsque l’équipement est exploité dans un environnement commercial. Cet équipement génère, utilise et peut émettre de l’énergie par radiofréquence et, s’il n’est pas installé et utilisé conformément au manuel d’instructions, peut causer des interférences nocives aux communications radio. L’utilisation de cet équipement dans une zone résidentielle est susceptible de causer des interférences nuisibles auquel cas l’utilisateur sera tenu de corriger l’interférence à ses propres frais. Ce dispositif est conforme à la partie 15 des règles de la FCC. L’opération est soumise aux deux conditions suivantes : (1) Cet appareil ne peut pas causer d’interférences nocives, et (2) cet appareil doit accepter toute interférence reçue, y compris toute interférence qui peut causer un fonctionnement indésirable. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Toute modification ou modification non expressément approuvée par la partie responsable de la conformité pourrait annuler le pouvoir de l’utilisateur d’exploiter cet équipement. GPS Industries, LLC Visage VDU User Manual 1 Contents 2 Starting up the Visage VDU 3 The Golf Map Screen 3 8 The Main Menu 8 9 Scorecard 10 Leader Board 11 Send Message 12 Order Food 14 Site Map 16 Settings GPS Industries, LLC Visage VDU User Manual 2 Starting up the Visage VDU When you turn on a unit, it will first go through a series of diagnostics. The screen will show a “booting up” message and a progress indicator. The Welcome Screen After boot up is complete, the VDU will typically show a course’s “Welcome Screen.” The Welcome Screen is an ad the course defines welcoming golfers to the course that displays when golf cars are near the clubhouse or in the staging area. GPS Industries, LLC Visage VDU User Manual 3 The Golf Map Screen The main screen that golfers will interact with is the Golf Map screen. This screen shows a map of the current hole and yardages to hazards and other point of interest. Flyovers When golfers first reach a hole, they will see a a 3D flyover to help them plan their strategy for the hole. After the flyover finishes playing, the screen will return to the golf map. Golfers can view the flyover again at any time by pressing the “view flyover” button on the screen. GPS Industries, LLC Visage VDU User Manual 4 Distances The Visage VDU uses GPS to calculate distances to hazards and other points of interest on the golf course. The distances are measured by line-of-sight (or “as the crow flies”), and may differ from yardages given on your course’s scorecard. Scorecard distances are typically measured by line-of-play, and so may be larger than the line-of-sight distance. Yards to Pin / Center of Green In the upper corner of the screen, there is a large box that shows the yardage to the pin if the course has defined a pin placement for that hole. If no pin placement is defined, the box will show the yardage to the center of the green, and the Pin icon will be replaced with a Center of Green icon. GPS Industries, LLC Visage VDU User Manual 5 Navigation Panel In the bottom corner of the screen, there is a navigation panel that allows golfers to access the main menu, view flyovers, and zoom in or out on the hole. If an insert ad is defined for the hole, it will display in this spot. If no ad is defined, the navigation panel will move the bottom of the screen. Ads During play, ads are shown in the corner of the screen. When you approach the green, you may see a full-screen ad. To dismiss this ad, touch the screen anywhere. Your car icon Your position is shown on the screen with an icon of a golf car. Note that other golf cars’ positions are not shown. GPS Industries, LLC Visage VDU User Manual 6 Tee shot distances After you hit your drive and move away from the teebox, Visage will display distances measured from your golf car back to up to five teeboxes. This yardage can be used to help you determine the distance of your drive. This is shown in an informational popup that appears at the bottom of the screen. Car Ahead On blind tee shots, the Visage VDU may warn the golfer that someone is in the driving area. View the approach/hole When you begin play on a hole, Visage first shows a “hole view,” or a map of the entire hole. As you approach the green, Visage will automatically zoom in to a “green view.” The golfer can elect to zoom in to the green view or back out to the hole view at any time by pressing the Zoom button on the screen. GPS Industries, LLC Visage VDU User Manual 7 Select another hole To select another hole, first press the “…

Text truncated - open the document above for the full version.

intertek.com 2 June 2022 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 To Whom It May Concern: Subject: Correction of Equipment Class of YEY‐V3‐1005A For the original application for YEY‐V3‐1005A submitted on 3/10/2021, the applicant used the list of equipment classes available from the FCC website and felt that DXT was the closest fit for their device. While reviewing the application, the reviewer determined based on the fact that historically DXT was for transceivers and DXX was for transmitters without a receiver that DXT was the appropriate classification. Reviewers are trained to use the official resources available to them rather than rely on memory. Given the equipment class was still showing as a valid option on the FCC website and was also consistent with historic practice, it was accepted as the equipment class on this application. Subsequently, when the first C2PC was filed on 3/10/2022, it was checked to make sure the same equipment class was chosen as it had to match the original. Afterwards, at the April 2022 TCB conference the FCC mentioned that DXT was being expired and the EAS was modified to remove DXT as an option for future filings. At this time, Intertek would like to request putting both of these applications into audit mode in order to upload this document and the request the FCC to change the equipment class on both to DXX. Yours sincerely Cliff Hansen TCB Operations Manager

Intertek 731 Enterprise Drive Lexington, KY 40510 Tel 859 226 1000 Fax 859 226 1040 www.intertek.com GPS Industries, LLC MPE REPORT SCOPE OF WORK MPE CALCULATION ON THE V3-1005A REPORT NUMBER 104290673LEX-002.2 ISSUE DATE REVISED DATE 4/10/2020 2/15/2021 PAGES 13 DOCUMENT CONTROL NUMBER Non-Specific EMC Report Shell Rev. December 2017 © 2017 INTERTEK This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services NA, Inc. MPE TEST REPORT Report Number: 104290673LEX-002.2 Project Number: G104290673 Report Issue Date: 4/10/2020 Report Revised Date: 2/15/2021 Product Name: V3-1005A Standards: FCC Part 1.1310 Limits for Maximum Permissible Exposure (MPE) RSS-102 Issue 5 RF Field Strength Limits for Devices Used by the General Public Tested by: Client: Intertek Testing Services NA, Inc. 731 Enterprise Drive Lexington, KY 40510 USA GPS Industries, LLC 1074 N. Orange Ave. Sarasota, FL 34236 USA Report prepared by Report reviewed by Bryan Taylor, Team Leader Brian Lackey, Staff Engineer Evaluation For: GPS Industries, LLC Product: V3-1005A EMC Test Report Date: 2/15/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 3 of 13 Report Number: 104290673LEX-002.2 Table of Contents 1 Introduction and Conclusion ........................................................................................................................... 4 2 Test Summary ................................................................................................................................................ 4 3 Client Information .......................................................................................................................................... 5 4 Description of Equipment under Test and Variant Models .............................................................................. 6 5 Antenna Gains: .............................................................................................................................................. 7 6 Output Power: ................................................................................................................................................ 8 7 FCC Limits ....................................................................................................................................................... 9 8 RSS-102 Issue 5 Exposure Limits: .................................................................................................................. 10 9 Test Procedure ............................................................................................................................................. 11 10 Results: ..................................................................................................................................................... 12 11 Revision History ........................................................................................................................................ 13 Evaluation For: GPS Industries, LLC Product: V3-1005A EMC Test Report Date: 2/15/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 4 of 13 Report Number: 104290673LEX-002.2 1 Introduction and Conclusion The tests indicated in section 2.0 were performed on the product constructed as described in section 4.0. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test Method, a list of the actual Test Equipment Used, documentation Photos, Results and raw Data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complies with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. Intertek does not make any claims of compliance for samples or variants which were not tested. 2 Test Summary Section Test full name Result 10 FCC Part 1.1310 Limits for Maximum Permissible Exposure (MPE) (Limits for General Population / Uncontrolled Exposure) Pass RSS-102 Issue 5 RF Field Strength Limits (For Devices Used by the General Public) Pass Evaluation For: GPS Industries, LLC Product: V3-1005A, Model V3-1005A MPE Report Date: 2/15/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 5 of 13 Report Number: 104290673LEX-002.2 3 Client Information This product was tested at the request of the following: Client Information Client Name: GPS Industries, LLC Address: 1074 N. Orange Ave. Sarasota, FL 34236 USA Contact: Karl Klinner Telephone: (941) 256-0572 Email: [email protected] Manufacturer Information Manufacturer Name: GPS Industries, LLC Manufacturer Address: 1074 N. Orange Ave. Sarasota, FL 34236 USA Evaluation For: GPS Industries, LLC Product: V3-1005A, Model V3-1005A MPE Report Date: 2/15/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 6 of 13 Report Number: 104290673LEX-002.2 4 Description of Equipment under Test and Variant Models Equipment Under Test Product Name V3-1005A Model Number V3-1005A Serial Number G 20 12 1014 Receive Date 3/23/20…

Text truncated - open the document above for the full version.

Intertek 731 Enterprise Drive Lexington, KY 40510 Tel 859 226 1000 Fax 859 226 1040 www.intertek.com GPS Industries, LLC TEST REPORT SCOPE OF WORK EMC TESTING – V3-1005A REPORT NUMBER 104290673LEX-003.1 ISSUE DATE REVISED DATE 4/10/2020 1/28/2021 PAGES 23 DOCUMENT CONTROL NUMBER Non-Specific EMC Report Shell Rev. December 2017 © 2017 INTERTEK This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services NA, Inc. EMC TEST REPORT (FULL COMPLIANCE) Report Number: 104290673LEX-003.1 Project Number: G104290673 Report Issue Date: 2/2/2021 Product Tested: Model Number: V3-1005A V3-1005A Standards: FCC Title 47 CFR Part 15.225 RSS-210 Issue 10 RSS-Gen Issue 5 Tested by: Client: Intertek Testing Services NA, Inc. 731 Enterprise Dr. Lexington, KY 40510 USA GPS Industries, LLC 1074 N. Orange Ave. Sarasota, FL 34236 USA Report prepared by Report reviewed by Bryan Taylor, Team Leader Brian Lackey, Staff Engineer Evaluation For: GPS Industries, LLC Product: V3-1005A EMC Test Report Date: 2/2/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 3 of 23 Report Number: 104290673LEX-003.1 Table of Contents 1 Introduction and Conclusion ..................................................................................................................... 4 2 Test Summary .......................................................................................................................................... 4 3 Client Information .................................................................................................................................... 5 4 Description of Equipment under Test and Variant Models .......................................................................... 6 5 System Setup and Method ........................................................................................................................ 7 6 Transmitter Fundamental and Spurious Emissions ..................................................................................... 9 7 Frequency Stability................................................................................................................................. 17 8 Occupied Bandwidth .............................................................................................................................. 19 9 Antenna Requirement ............................................................................................................................ 22 10 Revision History ................................................................................................................................. 23 Evaluation For: GPS Industries, LLC Product: V3-1005A EMC Test Report Date: 2/2/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 4 of 23 Report Number: 104290673LEX-003.1 1 Introduction and Conclusion The tests indicated in section 2.0 were performed on the product constructed as described in section 4.0. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test Method, a list of the actual Test Equipment Used, documentation Photos, Results and raw Data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complies with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. Intertek does not make any claims of compliance for samples or variants which were not tested. 2 Test Summary Section Test full name Result 6 Transmitter Fundamental and Spurious Emissions (ANSI C63.10: 2013, FCC Part 15.209, 15.225(a)-(d), RSS-210 Issue 10 § B.6(a)-(d), RSS-Gen Issue 5 § 8.9) Pass 7 Frequency Stability (ANSI C63.10: 2013, FCC Part 15.225(e), RSS-210 Issue 10 § B.6) Pass 8 Occupied Bandwidth (ANSI C63.10: 2013, RSS-Gen Issue 5 § 6.6, FCC Part 15.215c) Pass -- Conducted Emissions (ANSI C63.10: 2013) NA 1 9 Antenna Requirement (FCC Part 15.203, RSS-Gen Issue 5 § 8.3) Pass 1 The EUT did not connect AC mains in normal usage. The EUT is battery powered and uses chargeable batteries. The EUT batteries are charged through Golf Card batteries in normal use. Evaluation For: GPS Industries, LLC Product: V3-1005A EMC Test Report Date: 2/2/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 5 of 23 Report Number: 104290673LEX-003.1 3 Client Information This product was tested at the request of the following: Client Information Client Name: GPS Industries, LLC Address: 1074 N. Orange Ave. Sarasota, FL 34236 USA Contact: Karl Klinner Telephone: (941) 256-0572 Email: [email protected] Manufacturer Information Manufacturer Name: GPS Industries, LLC Manufacturer Address: 1074 N. Orange Ave. Sarasota, FL 34236 USA Evaluation For: GPS Industries, LLC Product: V3-1005A EMC Test Report Date: 2/2/2021 Non-Specific EMC Report Shell Rev. December 2017 Page 6 of 23 Report Number: 104290673LEX-003.1 4 Description of Equipment under Test and Variant Models Equipment Under Test Product Name V3-1005A Model Numb…

Text truncated - open the document above for the full version.

Frequency Stability Radiated Emissions Above 30MHz Radiated Emissions Below 30MHz Radiated Emissions Above 1GHz