YFJDSP1216HL1200 Series desktop SmartPanel with 16 hybrid lever keys

1200 Series User Manual 01-000HB03EG-J 00 SmartPanels 2.0 01-000HB03EG-J00 SmartPanels 2.0 User Manual © September 2025 Riedel Communications GmbH. Alle Rechte vorbehalten. Dieses Handbuch ist urheberrechtlich geschützt. Das Kopieren, Vervielfältigen, Übersetzen oder Umsetzen in irgendein elektronisches Medium oder maschinell lesbare Form im Ganzen oder in Teilen ohne vorherige schriftliche Genehmigung von Riedel ist nicht gestattet. Riedel übernimmt keine Gewähr für die Richtigkeit des Inhalts dieses Handbuchs. Die Rechte an anderen in diesem Handbuch erwähnten Marken- und Produktnamen liegen bei ihren Inhabern und werden hiermit anerkannt. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s) and complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage. (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Ce transmetteur ne doit pas etre place au meme endroit ou utilise simultanement avec un autre transmetteur ou antenne. Changes or modifications made to this equipment not expressly approved by Riedel may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device is granted pursuant to the Japanese Radio Law ( ) and the Japanese Telecommunications Business Law ( ). This device should not be modified (otherwise the granted designation number will become invalid). 01-000HB03EG-J 00 Standards·EN 50581:2012 ·EN 55032: 2015 ·EN 55035-2:2017 ·EN 61000-3-2:2014, EN 61000-3-3:2013 ·EN 61000-4-2:2009, EN 61000-4-3:2006+A1:2008+A2:2010, EN 61000-4-4:2012, EN 61000-4-5:2014, EN 61000-4-6:2014, EN 61000-4-8:2010, EN 61000-4-11:2004 ·IEC/EN 60950-1:2005+A1:2009+A2:2013 ·IEC/EN 62368-1:2014, UL/CSA 62368-1:2014 Industry Canada 8706A-DSP1216HL (1200 series SmartPanel DSP-1216HL) 8706A-RSP1216HL (1200 series SmartPanel RSP-1216HL) 8706A-RSP1232HL (1200 series SmartPanel RSP-1232HL) The device conforms to the following EU guidelines as attested by the CE mark. ·EMC 2014/30/EU ·LVD 2014/35/EU ·RoHS 2011/65/EU YFJDSP1216HL (1200 series SmartPanel DSP-1216HL) YFJRSP1216HL (1200 series SmartPanel RSP-1216HL) YFJRSP1232HL (1200 series SmartPanel RSP-1232HL) 202-SMI051 D 20-0017 202 (1200 series SmartPanel RSP-1216HL) 2 02-SMH033 D 19-0015 202 (1200 series SmartPanel RSP-1232HL) RSP-1232HL Audio Monitoring App A udio Monitoring App 1200 Series SmartPanels 2.0 User Manual 01-000HB03EG-J 00 Content 1 Preface 4 1.1Information..................................................................................................................... 5 1.2Change History............................................................................................................... 7 1.3Firmware Version........................................................................................................... 8 1.4About 1200 Series SmartPanels................................................................................... 9 2 D SP-1216HL SmartPanel 10 2.1Operating Elements..................................................................................................... 11 2.2Status LEDs.................................................................................................................... 12 2.3Lever Key Numbering.................................................................................................. 12 2.4Volume........................................................................................................................... 13 2 .5 I nfo Display . ................................................................................................................... 15 2.6Technical Specifications.............................................................................................. 16 3 R SP-1216HL SmartPanel 18 3.1Operating Elements..................................................................................................... 18 3.2Status LEDs.................................................................................................................... 19 3.3Lever Key Numbering..............................................................…

Text truncated - open the document above for the full version.

© cetecom advanced GmbH Page 1 of 41 TEST REPORT Test Report No.: 1-0403-25-01-08_TR1-R01 Testing Laboratory Applicant cetecom advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://cetecomadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS). The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12047-01-00. ISED Testing Laboratory Recognized Listing Number: DE0001 FCC designation number: DE0002 Riedel Communications GmbH Uellendahler Strasse 353 42109 Wuppertal/GERMANY Phone: +49 202 292 90 Contact: Collin Kreutzer e-mail: [email protected] Phone: +49 202 292-9137 Manufacturer Riedel Communications GmbH Uellendahler Strasse 353 42109 Wuppertal/GERMANY Combined Test report, applicable for: EC FCC ISED Test Item Kind of test item: Riedel Smart Panel Device type: fixed device Model name: DSP-1216HL S/N serial number: 1246030250056 FCC-ID: YFJDSP1216HL ISED Number: 8706A-DSP1216HL PMN: DSP-1216HL HVIN: DSP-1216HL HMN: -/- FVIN: V3.1.59 Hardware status: BOM3 Software status: n/a Frequency: 13.56 MHz RFID (tested) & Bluetooth 2.4 GHz (excluded) Antenna: integrated antenna Module information Max. power dissipation: 550mW (acc. customer spec) Power supply: 115 V AC by mains Test sample status: identical prototype Exposure category: general population / uncontrolled environment This test report is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test Report authorised: Test performed: Alexander Hnatovskiy Eric Tuettmann Lab Manager Testing Manager Radio Labs Radio Labs Test report no.: 1-0403-25-01-08_TR1-R01 © cetecom advanced GmbH Page 2 of 41 1 Table of contents 1 Table of contents ....................................................................................................................................... 2 2 General information .................................................................................................................................. 4 2.1 Notes and disclaimer ..................................................................................................................... 4 2.2 Application details ......................................................................................................................... 4 2.3 Statement of compliance ............................................................................................................... 4 3 Test standard/s: ......................................................................................................................................... 5 3.1 RF exposure limits ......................................................................................................................... 6 4 Reporting statements of conformity – decision rule ............................................................................. 7 5 Summary of Measurement Results ......................................................................................................... 8 6 Test Environment ...................................................................................................................................... 8 7 Test Set-up ................................................................................................................................................. 9 7.1 Measurement system ..................................................................................................................... 9 7.1.1 System Description ................................................................................................................ 9 7.1.2 Test environment ................................................................................................................. 10 7.1.3 Probe description ................................................................................................................. 10 7.1.4 Phantom description ............................................................................................................ 11 7.1.5 Device holder description .................................................................................................... 12 7.1.6 Laptop Extension Kit for Device holder ............................................................................... 12 7.1.7 Scanning procedure ............................................................................................................ 13 7.1.8 Spatial Peak SAR Evaluation .............................................................................................. 17 7.1.9 Data Storage and Evaluation............................................................................................... 20 7.1.10 Tissue simulating liquids: dielectric properties .................................................................... 22 7.1.11 Tissue simulating liquids: parameters ................................................................................. 22 7.1.12 Measurement uncertainty evaluation for SAR test .............................................................. 23 7.1.13 Measurement uncertainty evaluation for System Check ..................................................... 24 7.1.14 System check ...................................................................................................................... 25 7.1.15 System check procedure ..................................................................................................... 26 7.1.16 System validation ................................................................................................................ 27 8 Detailed…

Text truncated - open the document above for the full version.

Page 1 of 7 Annex C Photo documentation Appendix No.: 1-0403-25-01-08_TR1-A101-R01 Testing Laboratory cetecom advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken/Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://www.cetecomadvanced.com e-mail: [email protected] Appendix no.: 1-0403-25-01-08_TR1-A101-R01 Page 2 of 7 Photo 1: Measurement System DASY Photo 2: EUT Front view Appendix no.: 1-0403-25-01-08_TR1-A101-R01 Page 3 of 7 Photo 3: EUT Top view Photo 4: EUT rear view Appendix no.: 1-0403-25-01-08_TR1-A101-R01 Page 4 of 7 Photo 5: EUT side view Photo 6: EUT bottom view Appendix no.: 1-0403-25-01-08_TR1-A101-R01 Page 5 of 7 Photo 7: EUT Label Photo 8: Test Position Front Appendix no.: 1-0403-25-01-08_TR1-A101-R01 Page 6 of 7 Photo 9: Test Position Top Appendix no.: 1-0403-25-01-08_TR1-A101-R01 Page 7 of 7 Photo 10: Test Position Bottom Photo 11: Test Position Right

Compliance Certification Services (Kunshan) Inc. Page: 1 of 3 Appendix Photographs of Test Setup for KSCR2401000072AU Test Model No.: IDC777 Compliance Certification Services (Kunshan) Inc. Page: 2 of 3 Test Setup Photo Conducted Test Radiated Emissions (Below 1GHz) Compliance Certification Services (Kunshan) Inc. Page: 3 of 3 Radiated Emissions (Above 1GHz) Conducted Emissions at AC Power Line (150kHz-30MHz)

Annex A104 - Photographs No. 1-0403-25-01-01_TR1-A104-R01 August 19, 2025 DescriptionTest setup photos This document is electronically signed and valid without handwritten signature. Public keys for verifcation of the electronic signatures can be requested at the testing laboratory. Marco Bertolino Supervisor Radio Services Radio Labs authorized by cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 1 of 7 Photo 1 Photo 2 cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 2 of 7 Photo 3 Photo 4 cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 3 of 7 Photo 5 Photo 6 cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 4 of 7 Photo 7 Photo 8 cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 5 of 7 Photo 9 cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 6 of 7 Document History End of document ReleaseApplied changesRelease date R01initial releaseAugust 19, 2025 cetecom advanced GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken Document No. 1-0403-25-01-01_TR1-A104-R01 Page 7 of 7

Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240100007202 Page: 1 of 125 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Member of the SGS Group (SGS SA) TEST REPORT Application No.: KSCR2401000072AU FCC ID: 2A3WYIDC777 IC: 30237-IDC777 Applicant: CompanyDeep Ltd Address of Applicant: St John’s Innovation Centre, Cowley Road, Cambridge, CB4 0WS, United Kingdom Manufacturer: CompanyDeep Ltd Address of Manufacturer: St John’s Innovation Centre, Cowley Road, Cambridge, CB4 0WS, United Kingdom Equipment Under Test (EUT): EUT Name: IDC7 Bluetooth Module Model No.: IDC777 Trade Mark Standard(s) : 47 CFR Part 15, Subpart C 15.247 RSS-247 Issue 3, August 2023 RSS-Gen Issue 5 Amendment 2 (February 2021) Date of Receipt: 2024-01-12 Date of Test: 2024-01-16 to 2024-01-19 Date of Issue: 2024-01-24 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240100007202 Page: 2 of 125 Revision Record Version Description Date Remark 00 Original 2024-01-24 / Authorized for issue by: Tested By Maker_Qi/Project Engineer Approved By Terry Hou /Reviewer Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240100007202 Page: 3 of 125 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Customer Declaration Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence N/A 47 CFR Part 15, Subpart C 15.247(a)(1),(g),(h) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Conducted Peak Output Power ANSI C63.10 (2013) Section 7.8.5 47 CFR Part 15, Subpart C 15.247(b)(1) Pass 20dB Bandwidth ANSI C63.10 (2013) Section 7.8.7 47 CFR Part 15, Subpart C 15.247(a)(1) Pass Carrier Frequencies Separation ANSI C63.10 (2013) Section 7.8.2 47 CFR Part 15, Subpart C 15.247a(1) Pass Hopping Channel Number ANSI C63.10 (2013) Section 7.8.3 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Dwell Time ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 7.8.6 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 7.8.8 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Frequency Stability RSS-Gen Section 6.11 RSS-Gen Section 8.11 Pass Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240100007202 Page: 4 of 125 3 Contents Page 1 COVER PAGE ...................................................................................................................................... 1 2 Test Summary ........................................................................................................................................... 3 3 Contents .................................................................................................................................................... 4 4 General Information .................................................................................................................................. 5 4.1 Details of E.U.T. ................................................................................................................................. 5 4.2 Power level setting using in test: ......................................................................................................... 5 4.3 Description of Support Units ............................................................................................................... 5 4.4 Measurement Uncertainty ................................................................................................................... 6 4.5 Test Location ...................................................................................................................................... 7 4.6 Test Facility ........................................................................................................................................ 7 4.…

Text truncated - open the document above for the full version.

TEST REPORT Test report no.: 1-0403-25-01-14_TR1-R01 Testing laboratory Applicant cetecom advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://cetecomadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS). The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12047-01-00. ISED Testing Laboratory Recognized Listing Number: DE0001 FCC designation number: DE0002 Riedel Communications GmbH Uellendahler Strasse 353 42109 Wuppertal / GERMANY Phone: +49 202 292 90 Contact: Collin Kreutzer e-mail: [email protected] Manufacturer Riedel Communications GmbH Uellendahler Strasse 353 42109 Wuppertal / GERMANY Test standard/s FCC - Title 47 CFR Part 15 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 247 Issue 4 Digital Transmission Systems, Frequency Hopping Systems and Licence-Exempt Local Area Network Devices in 902-928 MHz, 2400-2483.5 MHz, 5150-5350 MHz, and 5470-5895 MHz bands For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: Riedel Smart Panel Model name: DSP-1216HL FCC ID: YFJDSP1216HL ISED certification number: 8706A-DSP1216HL Frequency: 2400 MHz to 2483.5 MHz Technology tested: Bluetooth ® + EDR Antenna: Integrated antenna Power supply: 115 V AC by mains Temperature range: 0°C to +45°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: On behalf of Michael Dorongovski Rene Oelmann Lab Manager Lab Manager Radio Labs Radio Labs Test report no.: 1-0403-25-01-14_TR1-R01 © cetecom advanced GmbH Page 2 of 37 1 Table of contents 1 Table of contents .................................................................................................................................... 2 2 General information ................................................................................................................................ 3 2.1 Notes and disclaimer .................................................................................................................... 3 2.2 Application details ........................................................................................................................ 3 2.3 Test laboratories sub-contracted .................................................................................................. 3 3 Test standard/s, references and accreditations ....................................................................................... 4 4 Reporting statements of conformity – decision rule ................................................................................ 5 5 Test environment.................................................................................................................................... 6 6 Test item ................................................................................................................................................ 6 6.1 General description ...................................................................................................................... 6 6.2 Additional information .................................................................................................................. 6 7 Description of the test setup ................................................................................................................... 7 7.1 Shielded semi anechoic chamber .................................................................................................. 8 7.2 Shielded fully anechoic chamber .................................................................................................. 9 7.3 Radiated measurements > 18 GHz .............................................................................................. 10 7.4 AC conducted ............................................................................................................................. 11 8 Sequence of testing .............................................................................................................................. 12 8.1 Sequence of testing radiated spurious 9 kHz to 30 MHz .............................................................. 12 8.2 Sequence of testing radiated spurious 30 MHz to 1 GHz ............................................................. 13 8.3 Sequence of testing radiated spurious 1 GHz to 18 GHz .............................................................. 14 8.4 Sequence of testing radiated spurious above 18 GHz .................................................................. 15 9 Measurement uncertainty ..................................................................................................................... 16 10 Summary of measurement results ..................................................................................................... 17 11 Additional comments ........................................................................................................................ 18 12 Measurement results ........................................................................................................................ 19 12.1 Radiated peak power ............................................................................................................... 19 12.2 Band edge compliance radiated ............................................................................................... 20 12.3 Spurious emissions radiated below 30 MHz ...........................................…

Text truncated - open the document above for the full version.

             !"#$%&'(")%*%)$#%+,-../01/0112 3$4". +*5   67 8    9 0:;1<=:0>.11? 7 @ 5AB$CD E  F G 0:11H0;11IJK?7   ;1L  M  1N>%#O(DPQRHSTU7   G 7   H:1#+V2;WX Y  G   H.D;N>%#O(DPQRHST Z  F0[111   \ ]D;N>B%,D ^ E    _  `   a""N3+%,# ?  \ bb c d bb  \ bb d bb  bb   G    I+e,##J"f"N"g%)"fh%#Jij+h,B$jk*$)%,4e(Dl,%#f-BB m%,"h%N#JfJ+e&Ni"N"f%4,"N#+(j+g%N";1L%B( "N$,)"B$#)J%,4)J$j$)#"j%f#%)fD no+#"-3%,f5p:[$&#J+e4Jqo+X+,,")#q[Bef#i"f+&N"j"N#+%#f3X> ($Nf*+j(j+("j"&")#j%)$&+("j$#%+, rd _  _ G 9rd _ _ G s+J$,f+,=")J,+&+4O[t,)Dj"f"jg"f#J"j%4J##+B$k"N"f%4,)J$,4"fh%#J+e#,+#%)"D <&&f$&"f$j"feiu" )##+s+J$,f+,=")J,+&+4O[t,)D#"jBf$,N)+,N%#%+,fD @@@^v_  _ GF^ :11.X$&&"=")$#"wX$B$j%&&+[X<]51.0w=xm21;D52]D..yya<Q21;D52]D.20. 0112s+J$,f+,=")J,+&+4O[t ,)D<&&z%4J#fz"f"jg"N n<,)J+j%,43%,HoX n<,)J+j%,43%,HoX <,)J+j%,43%,HoX 1D1011D1.01D;11D51 1D1{]0D11VD11:/HD112V1D./H1D0 1D1121D01 1D;1 1D1121D01 0Dy11D01 |}~€‚ƒ„…ƒ†‡ˆ‰ƒ‚Š‹~‡ŒŽ…~†| 1D01 0D11 1D101 1D.101D112 1D112 1D.]{ 1D1{] ;D11 $ = A. ‘’ “ ” •?8 _ G – ?  —^ r–\˜™6š› ?  —c^c r–\˜™cc6š› m. A m     !!"#$"$% &'# ( )*+, -.- , /+, -01 / , /+2 +,234 5 06  2 5 /78 9 :/ ;522 <=>?>'@AB <=>B?>'@AB C>DE>'FGHIADAJD>A'>KLMD'>'DN>BI ODDADBPQ C>DE>'FGHIAKDMMDI RRRST51 25 ,1 5-5U)S,5V W$$!@EX@KAG@OY($!#XEZ[%$\I(%YI!!]]^O_%$\I(%YI!%#! #$$%C>DE>'FGH IO`'>D`DAJM abcdefghijhklmnhgopclqrsjtcrkua < < < < < < < < <     !!"#$"$% &'( ( )*+, -. /+ +0  1 2 345675'896 :5;<5'=>?@9;9A;59'5BCD;'5';E56@ F;;9;6GH :5;<5'=>?@9B;DD;@ IIIJK0L 20 ,L 0-0M)J,0N O$$!8<P8B9>8FQ($!#P<RS%$T@(%Q@!!UUVFW%$T@(%Q@!%#! #$$%:5;<5'=>? @FX'5;X;9AD YZ[\]^_`ab`cdef`_gh[dijkbl[jcmY 3 3 3 3 3 3 3 3 3

Page 1 of 24 Annex D Appendix No.: 1-0403-25-01-08_TR1-A201-R01 Testing Laboratory cetecom advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken/Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://www.cetecomadvanced.com e-mail: [email protected] Accredited Test Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate starting with the registration number: D-PL-12047-01-00. Appendix with Calibration data, Phantom certificate and system check information 2012-01-16 Test report no.: 1-0403-25-01-08_TR1-A201-R01 Page 2 of 24 1 Table of contents 1 Table of contents .......................…

Text truncated - open the document above for the full version.