YHLBLUB1680VSmart Phone

MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ26050352S02 Annex C Plots of T-Coil Test Results T-Coil Coupling Mode Test Report Results Primary Group Contiguous Point CountSecondary Group Point CountSecondary Group Max LongitudinalSecondary Group Max Transverse 2905162426 T-Coil Noise Test Report Measurement performed on June 20, 2026 at 05:16 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 2UMTS-FDD (WCDMA, AMR)94001880.0 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Secondary Group Point CountSecondary Group Max LongitudinalSecondary Group Max TransverseHmax [dB(A/m)] 5162426-28.66 T-Coil Signal Test Report Measurement performed on June 20, 2026 at 05:06 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 2UMTS-FDD (WCDMA, AMR)94001880.0 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Audio FileMeasurement Duration [s]Gain [dB]Hmax [dB(A/m)] 48k_voice_1kHz_1s.wav2.0-8.486.12 T-Coil Signal Test Report Measurement performed on June 20, 2026 at 05:06 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 2UMTS-FDD (WCDMA, AMR)94001880.0 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Audio FileMeasurement Duration [s]Margin Upper Bound [dB]Margin Lower Bound [dB] 48k_voice_300-3000_2s.wav2.01.222.0 T-Coil Coupling Mode Test Report Results Primary Group Contiguous Point CountSecondary Group Point CountSecondary Group Max LongitudinalSecondary Group Max Transverse 3005242526 T-Coil Noise Test Report Measurement performed on June 20, 2026 at 05:38 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 4UMTS-FDD (WCDMA, AMR)14131732.6 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Secondary Group Point CountSecondary Group Max LongitudinalSecondary Group Max TransverseHmax [dB(A/m)] 5242526-28.9 T-Coil Signal Test Report Measurement performed on June 20, 2026 at 05:29 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 4UMTS-FDD (WCDMA, AMR)14131732.6 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Audio FileMeasurement Duration [s]Gain [dB]Hmax [dB(A/m)] 48k_voice_1kHz_1s.wav2.0-8.486.16 T-Coil Signal Test Report Measurement performed on June 20, 2026 at 05:29 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 4UMTS-FDD (WCDMA, AMR)14131732.6 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Audio FileMeasurement Duration [s]Margin Upper Bound [dB]Margin Lower Bound [dB] 48k_voice_300-3000_2s.wav2.01.092.0 T-Coil Coupling Mode Test Report Results Primary Group Contiguous Point CountSecondary Group Point CountSecondary Group Max LongitudinalSecondary Group Max Transverse 3956142626 T-Coil Noise Test Report Measurement performed on June 20, 2026 at 23:07 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 5UMTS-FDD (WCDMA, AMR)4182836.4 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Secondary Group Point CountSecondary Group Max LongitudinalSecondary Group Max TransverseHmax [dB(A/m)] 6142626-29.36 T-Coil Signal Test Report Measurement performed on June 20, 2026 at 22:55 Device Under Test ManufacturerModelDimensions [mm]Speaker Position [mm] 146.2 x 71.8 x 7.5144.3 Hardware Setup Probe NameProbe Calibration DateDAE NameDAE Calibration Date AM1DV3 - 1048November 19, 2025DAE4 Sn1643March 16, 2026 Communication Systems Band NameCommunication Systems NameChannelFrequency [MHz] Band 5UMTS-FDD (WCDMA, AMR)4182836.4 Grid Settings Extent X [mm]Extent Y [mm]Step X [mm]Step Y [mm]Distance [mm] 52.052.04.04.010.0 Results Audio FileMeasurement Duration [s]Gain [dB]Hmax [dB(A/m)] 48k_voice_1kHz_1s.wav2.0-8.486.4 T-Coil Signal Test Report Measurement performed on June 20, 2026 at 22:55 Device Und…

Text truncated - open the document above for the full version.

Annual validation for test lab. Appendix Annual validation for Test Lab. General calibration information Date 2025.09.25 Test Laboratory ShenZhen Morlab Communications Technology Co., Ltd. Antenna serial No. D3500V2-SN:1104 Antenna Parameters with Head TSL Impedance, transformed to feed point 50.319Ω-0.433jΩ Return Loss -45.408dB General Antenna Parameters and Design Electrical Delay (one direction) 1.276 ns After long term use with 100W radiated power，only a slight warming of the dipole near the feed point can be measured The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard No excessive force must be applied to the dipole arm， because they might bend or the soldered connections near the feed point may be damaged . Annual validation for test lab. Annual validation for test lab. Appendix Impedance Measurement Plot for Head TSL

Annual validation for test lab. Appendix Annual validation for Test Lab. General calibration information Date 2025.09.25 Test Laboratory ShenZhen Morlab Communications Technology Co., Ltd. Antenna serial No. D3700V2-SN:1076 Antenna Parameters with Head TSL Impedance, transformed to feed point 49.085Ω+0.608jΩ Return Loss -39.103dB General Antenna Parameters and Design Electrical Delay (one direction) 1.276 ns After long term use with 100W radiated power，only a slight warming of the dipole near the feed point can be measured The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard No excessive force must be applied to the dipole arm， because they might bend or the soldered connections near the feed point may be damaged . Annual validation for test lab. Annual validation for test lab. Appendix Impedance Measurement Plot for Head TSL

Annual validation for test lab. Appendix Annual validation for Test Lab. General calibration information Date 2025.09.25 Test Laboratory ShenZhen Morlab Communications Technology Co., Ltd. Antenna serial No. D3900V2-SN:1046 Antenna Parameters with Head TSL Impedance, transformed to feed point 45.751 Ω+3.987 jΩ Return Loss -24.322 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.276 ns After long term use with 100W radiated power，only a slight warming of the dipole near the feed point can be measured The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard No excessive force must be applied to the dipole arm， because they might bend or the soldered connections near the feed point may be damaged . Annual validation for test lab. Annual validation for test lab. Appendix Impedance Measurement Plot for Head TSL

Annual validation for test lab. Appendix Annual validation for Test Lab. General calibration information Date 2025.09.25 Test Laboratory ShenZhen Morlab Communications Technology Co., Ltd. Antenna serial No. D5250V2-SN: 1176 Antenna Parameters with Head TSL Impedance, transformed to feed point 51.07Ω+2.05jΩ Return Loss -32.818dB General Antenna Parameters and Design Electrical Delay (one direction) 1.276 ns After long term use with 100W radiated power，only a slight warming of the dipole near the feed point can be measured The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard No excessive force must be applied to the dipole arm， because they might bend or the soldered connections near the feed point may be damaged . Annual validation for test lab. Annual validation for test lab. Appendix Impedance Measurement Plot for Head TSL Annual validation for test lab. Appendix Annual validation for Test Lab. General calibration information Date 2025.09.25 Test Laboratory ShenZhen Morlab Communications Technology Co., Ltd. Antenna serial No. D5600V2-SN: 1176 Antenna Parameters with Head TSL Impedance, transformed to feed point 50.89Ω-2.58jΩ Return Loss -31.355dB General Antenna Parameters and Design Electrical Delay (one direction) 1.276 ns After long term use with 100W radiated power，only a slight warming of the dipole near the feed point can be measured The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard No excessive force must be applied to the dipole arm， because they might bend or the soldered connections near the feed point may be damaged . Annual validation for test lab. Annual validation for test lab. Appendix Impedance Measurement Plot for Head TSL Annual validation for test lab. Appendix Annual validation for Test Lab. General calibration information Date 2025.09.25 Test Laboratory ShenZhen Morlab Communications Technology Co., Ltd. Antenna serial No. D5750V2-SN: 1176 Antenna Parameters with Head TSL Impedance, transformed to feed point 50.962Ω+0.196jΩ Return Loss -40.247dB General Antenna Parameters and Design Electrical Delay (one direction) 1.276 ns After long term use with 100W radiated power，only a slight warming of the dipole near the feed point can be measured The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short-circuited for DC-signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard No excessive force must be applied to the dipole arm， because they might bend or the soldered connections near the feed point may be damaged . Annual validation for test lab. Annual validation for test lab. Appendix Impedance Measurement Plot for Head TSL

NOTE: This document is issued by Shenzhen Morlab Communications Technology Co., the test report shall not be reproduced except in full without prior written permission of the company. The test results apply only to the particular sample(s) tested and to the specific tests carried out which is available on request for validation and information confirmed at our website. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ26050351S01 Page 1 of 99 TEST REPORT APPLICANT : BLU Products, Inc. PRODUCT NAME : Smart Phone MODEL NAME : B1680V BRAND NAME : BLU FCC ID : YHLBLUB1680V STANDARD(S) : FCC 47 CFR Part 2 (2.1093) IEEE 1528-2013 RECEIPT DATE : 2026-06-04 TEST DATE : 2026-06-23 to 2026-07-07 ISSUE DATE : 2026-07-15 Edited by: Pang Siyu (Rapporteur) Approved by: Shen Junsheng (Supervisor) MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ26050351S01 Page 2 of 99 DIRECTORY 1. Statement of Compliance·································································································· 6 2. Technical Information ········································································································ 7 2.1. Applicant and Manufacturer Information ····································································· 7 2.2. Equipment under Test (EUT) Description ···································································· 7 2.3. Environment of Test Site/Conditions ··········································································· 9 3. Specific Absorption Rate (SAR) ····················································································· 10 3.1. Introduction···················································································································· 10 3.2. SAR Definition ··············································································································· 10 4. RF Exposure Limits ········································································································· 11 4.1. Uncontrolled Environment ··························································································· 11 4.2. Controlled Environment ······························································································· 11 5. Applied Reference Documents ······················································································ 12 6. SAR Measurement System ····························································································· 13 6.1. E-Field Probe ················································································································· 14 6.2. Data Acquisition Electronics (DAE) ············································································ 15 6.3. Robot ······························································································································ 15 6.4. Measurement Server ····································································································· 16 6.5. Light Beam Unit ············································································································· 16 6.6. Phantom ························································································································· 16 6.7. Device Holder ················································································································ 17 6.8. Data Storage and Evaluation ······················································································· 18 6.9. Test Equipment List ······································································································ 20 7. Tissue Simulating Liquids ······························································································ 22 8. SAR System Verification ································································································· 24 8.1. Purpose of System Performance Check ···································································· 24 8.2. System Setup ················································································································· 24 MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ26050351S01 Page 3 of 99 8.3. Validation Results ········································································································· 25 9. EUT Testing Position ······································································································· 29 9.1. Handset Reference Points ··························································································· 29 9.2. Positioning for Cheek / Touch ····················································································· 30 9.3. Positioning for Ear / 15º Tilt ························································································· 30 9.4. SAR Evaluation near the Mouth/Jaw Regions of the Phantom ······························ 31 9.5. Body-worn Configurations ·························································································· 31 9.6. Hotspot Mode Exposure Position Conditions ·························································· 32 10. Measurement Procedures ·…

Text truncated - open the document above for the full version.

Antenna Report Mobile antenna test report For FCC ID: YHLBLUB1680V Shenzhen Fubang Wireless Technology Co., Ltd. RF:WangYu Date:2026.07.02 Office address: Room 301, 3rd Floor, Building 1, Lianjian Industrial Park, Huarong Road, Longhua District, Shenzhen City Test equipment Wireless communications test set: CMW500/MT8000A Network Analyzer: Agilent 5071C Anechoic Chamber : GTS 2800 Antenna information Customer . Antenna model FPC Antenna type PIFA AntennaSupport Band ANT 0 UMTS: B5 TRX LTE: B5/12/13/17 TRX NR: N5 TRX ANT 1 LTE:B2/4/66 PRXMIMO NR:N2/66 PRXMIMO NR:N77 DRX ANT 2 UMTS:B2/4 DRX LTE: B2/4/7/66 DRX NR: N2/66 DRX NR:N77 PRXMIMO ANT 3 NR:N77 TRX ANT 4 UMTS: B5 DRX LTE: B5/12/13/17 DRX NR: N5 DRX UMTS:B2/4 TRX LTE: B2/4/7/66 TRX NR: N2/66 TRX ANT 5GPS L1+BT+2.4G&5G WIFI ANT 6 LTE: B2/4/66 DRXMIMO NR: N2/66 ANT 7 NR: N77 DRXMIMO Antenna Location Antenna Max. Peak Gain: ANT 0 Band Gain WCDMA B5/LTE B5/N5 -4.0 LTE B12 -3.1 LTE B13 -3.6 LTE B17 -3.1 LTE B20 -3.7 LTE B28 -3.3 ANT 1 RX Band Gain LTE B2 -0.16 LTE B66 -1.4 ANT 3 Band Gain N77 -0.2 ANT 4 Band Gain WCDMA B2/LTE B2/N2 -1.9 LTE B4 -1.2 LTE B7 -0.8 LTE B66/N66 -1.2 ANT 5 Band Gain GPS -0.2 2.4G WIFI/BT -0.1 5G WIFI -1.2 3.Radiation pattern diagram 603MHZ~960MHZ 1710MHZ~2170MHZ 2300MHZ~2360MHZ 3300MHZ~4200MHZ 1550~1600MHz（GPS） 2400MHZ~2500MHZ(BT/WIFI 2.4G) 5150MHZ~5850MHZ(WIFI 5G) Dimensional drawing of main antenna Dimensional drawing of GPS/WIFI/BT antenna Dimensional drawing of diversity antenna

NOTE: This document is issued by Shenzhen Morlab Communications Technology Co., Ltd., the test report shall not be reproduced except in full without prior written permission of the company. The test results apply only to the particular sample(s) tested and to the specific tests carried out which is available on request for validation and information confirmed at our website. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 1 of 76 REPORT No.：SZ26050351W01 TEST REPORT APPLICANT : BLU Products, Inc. PRODUCT NAME : Smart Phone MODEL NAME : B1680V BRAND NAME : BLU FCC ID : YHLBLUB1680V STANDARD(S) : 47 CFR Part 15 Subpart C RECEIPT DATE : 2026-05-26 TEST DATE : 2026-06-08 to 2026-07-09 ISSUE DATE : 2026-07-14 Edited by: Zeng Xiaoying (Rapporteur) Approved by: Shen Junsheng (Supervisor) MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 2 of 76 REPORT No.：SZ26050351W01 DIRECTORY 1. Summary of Test Result ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 4 1.1. Testing Applied Standards ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 4 1.2. Test Equipment List ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 5 1.3. Measurement Uncertainty ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 7 1.4. Testing Laboratory ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 7 2. General Description ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 2.1. Information of Applicant and Manufacturer ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 2.2. Information of EUT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 2.3. Channel List of EUT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 9 2.4. Test Configuration of EUT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 10 2.5. Test Conditions ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 10 2.6. Test Setup Layout Diagram ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 10 3. Test Results ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 13 3.1. Antenna Requirement ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 13 3.2. Duty Cycle of Test Signal ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 14 3.3. Maximum Peak Conducted Output Power ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 15 3.4. Maximum Average Conducted Output Power ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 16 3.5. 6 dB Bandwidth ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 17 3.6. Conducted Spurious Emissions and Band Edge ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 18 3.7. Power Spectral Density ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 19 3.8. Conducted Emission ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 20 3.9. Restricted Frequency Bands ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 21 3.10. Radiated Emission ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 22 Annex A Test Data and Result ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 24 Notes ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 76 MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 3 of 76 REPORT No.：SZ26050351W01 Change History Version Date Reason for change 1.0 2026-07-14 First edition MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 4 of 76 REPORT No.：SZ26050351W01 1. Summary of Test Result No. Section Description Test Date Test Engineer Result Remark 1 15.203 Antenna Requirement N/A N/A PASS / 2 N/A Duty Cycle of Test Signal Jun. 08, 2026 Li Xinpeng PASS / 3 15.247(b) Maximum Peak Conducted Output Power Jun. 08, 2026 Li Xinpeng PASS / 4 15.247(b) Maximum Average Conducted Output Power Jun. 08, 2026 Li Xinpeng PASS / 5 15.247(a) Bandwidth Jun. 08, 2026 Li Xinpeng PASS / 6 15.247(d) Conducted Spurious Emission and Band Edge Jun. 08, 2026 Li Xinpeng PASS / 7 15.247(e) Power Spectral Density Jun. 08, 2026 Li Xinpeng PASS / 8 15.207 Conducted Emission Jul. 09, 2026 Wang Yapeng PASS / 9 15.247(d) Restricted Frequency Bands Jun. 29, 2026 Li Hanbin PASS / 10 15.209, 15.247(d) Radiated Emission Jun. 30, 2026 Li Hanbin PASS / Note 1: The tests were performed according to the method of measurements prescribed in ANSI C63.10-2020 and KDB 558074 D01 v05r02. Note 2: Any additions, deviation, or exclusions from the method shall be noted in the “Remark”. 1.1. Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:  47 CFR Part 15 Subpart C Radio Frequency Devices MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, N…

Text truncated - open the document above for the full version.

NOTE: This document is issued by Shenzhen Morlab Communications Technology Co., Ltd., the test report shall not be reproduced except in full without prior written permission of the company. The test results apply only to the particular sample(s) tested and to the specific tests carried out which is available on request for validation and information confirmed at our website. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 1 of 127 REPORT No.：SZ26050351W03 TEST REPORT APPLICANT : BLU Products, Inc. PRODUCT NAME : Smart Phone MODEL NAME : B1680V BRAND NAME : BLU FCC ID : YHLBLUB1680V STANDARD(S) : 47 CFR Part 15 Subpart C RECEIPT DATE : 2026-05-26 TEST DATE : 2026-06-08 to 2026-07-09 ISSUE DATE : 2026-07-14 Edited by: Zeng Xiaoying (Rapporteur) Approved by: Shen Junsheng (Supervisor) MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen, GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 2 of 127 REPORT No.：SZ26050351W03 DIRECTORY 1. Summary of Test Result ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 4 1.1. Testing Applied Standards ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 5 1.2. Test Equipment List ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 6 1.3. Measurement Uncertainty ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 1.4. Testing Laboratory ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 2. General Description ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 9 2.1. Information of Applicant and Manufacturer ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 9 2.2. Information of EUT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 9 2.3. Channel List of EUT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 10 2.4. Test Configuration of EUT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 11 2.5. Test Conditions ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 11 2.6. Test Setup Layout Diagram ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 12 3. Test Results ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 15 3.1. Antenna Requir…

Text truncated - open the document above for the full version.