YI4DWF20UXP33Microwave Oven

MICROWAVE OVEN INSTRUCTION MANUAL F20UXP33-A70 IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY AND KEEP FOR FUTURE REFERENCE 2 Household use only SAVE THESE INSTRUCTIONS .IMPORTANT SAFEGUARDS............。。.................. ... .. When using electrical appliances basic safety precautions should be followed, including the following: WARNING – To reduce the risk of burns, electric shock, fire, injury to persons, or exposure to excessive microwave energy: 1. Read all instructions before using the appliance. 2. Read and follow the specific "PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY" found on page 8. 3. This appliance must be grounded. Connect only to properly grounded outlet. See "GROUNDING INSTRUCTIONS" found on page 9. 4. Install or locate this appliance only in accordance with the provided installation instructions. 5. Some products such as whole eggs and sealed containers – for example, closed glass jars – are able to explode and should not be heated in this oven. 6. Use this appliance only for its intended use as described in the manual. Do not use corrosive chemicals or vapors in this appliance. This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use. 7. As with any appliance, close supervision is necessary when used by children. 8. Do not operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped. 9. This appliance should be serviced only by qualified service personnel. Contact nearest authorized service facility for examination, repair, or adjustment. 10. Do not cover or block any openings on the appliance. 11. Do not store this appliance outdoors. Do not use this 3 product near water – for example, near a kitchen sink, in a wet basement, near a swimming pool, or similar locations. 12. Do not immerse cord or plug in water. 13. Keep cord away from heated surfaces. 14. Do not let cord hang over edge of table or counter. 15. When cleaning surfaces of door and oven that comes together on closing the door, use only mild, nonabrasive soaps, or detergents applied with a sponge or soft cloth. 16. To reduce the risk of fire in the oven cavity: a. Do not overcook food. Carefully attend appliance when paper, plastic, or other combustible materials are placed inside the oven to facilitate cooking. b. Remove wire twist-ties from paper or plastic bags before placing bag in oven. c. If materials inside the oven ignite, keep oven door closed, turn oven off, and disconnect the power cord, or shut off power at the fuse or circuit breaker panel. d. Do not use the cavity for storage purposes. Do not leave paper products, cooking utensils, or food in the cavity when not in use. 17. Liquids, such as water, coffee, or tea are able to be overheated beyond the boiling point without appearing to be boiling. Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHEN THE CONTAINER IS DISTURBED OR A UTENSIL IS INSERTED INTO THE LIQUID. 18. Notice for extension cord: a. A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord. b. Longer cord sets or extension cords are available and may be used if care is exercised in their use. c. If a long cord or extension cord is used: 1) The marked electrical rating of the cord set or extension 4 cord should be at least as great as the electrical rating of the appliance. 2) The extension cord must be a grounding-type 3-wire cord; and 3) The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped over unintentionally. The following basic precautions should always be followed when using electrical appliance: 1. Read all instructions before using. 2. Make sure the voltage in your living area corresponding to the one shown on the rating label of the appliance. And the wall socket is properly grounded. 3. TO reduce the risk of fire in the oven cavity: a. DO not overcook the food. b. Remove wire twist -ties from paper or plastic bags before placing bags in the oven. c. Do not heat oil or fat for deep drying as the temperature of oil cannot be controlled. d. After use wipe the waveguide cover with a damp cloth, followed by dry cloth to remove any food splashes and grease. Built -up grease may overheat and begin to cause smoke or catch fire. e. If materials inside the oven should smoke or ignite, keep oven door closed, turn oven off and disconnect the power supply. f. Close supervision is necessary when using disposable containers made from plastic, paper or other combustible material. 4. TO reduce the risk of explosion and sudden boiling: a. Do not place sealed containers in the oven. Baby bottles fitted with a screw cap or teat are considered to be sealed containers. b. When boiling liquid in the oven, use the wide -mouthed container and stand about 20 seconds at the end of 5 cooking to avoid delayed eruptive boiling of liquids. c. Potatoes, sausage and chestnut should be peeled or pierced before cooking. Eggs in their shell, whole hard -boiled eggs should not be heated in microwave ovens since they may explode, even after microwave heating has ended. d. The cooked liquid should not be removed out immediately. Several moments should be waited before removing. In order to avoid possible hazards caused by delayed eruptive boiling of 1iquids. e. The contents of feeding bottles and baby food jars are to be stirred or shaken and the temperature is to be checked before consumption, in order to avoid burns. 5. Never operate the oven further if the door or door seals is damaged or the oven is malfunctioned or supply cord is damaged. Return the appliance to the nearest authorised service center for repair and maintenance. Never try to adjust or repair the oven yourself. 6. If t…

Text truncated - open the document above for the full version.

Guangdong Welly Electrical Appliances Co., Ltd Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, China Tel: +86 0760-22507015 Email: [email protected] CFR 47 §2.911(d)(5)(i) Attestation Letter Attestation Letter Date: 2025-12-8 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: YI4DWF20UXP33 Guangdong Welly Electrical Appliances Co.,Ltd certifies that the equipment for which authorization is sought, is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature: Printed Name: Gao Yanjun Title: Engineer

Guangdong Welly Electrical Appliances Co., Ltd Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, China Tel: +86 0760-22507015 Email: [email protected] CFR 47 §2.911 (d)(5)(ii) Attestation Letter Attestation Letter Date: 2025-12-8 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: YI4DWF20UXP33 Guangdong Welly Electrical Appliances Co.,Ltd certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, Signature: Printed Name: Gao Yanjun Title: Engineer

U.S. AGENT LETTER OF ATTESTATION Date: 2025-12-8 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: YI4DWF20UXP33 Guangdong Welly Electrical Appliances Co.,Ltd certifies that, as of the date of the filing of the application, Emerson Radio Corp. is our designated U.S. agent for service of process for the above referenced FCC ID. Guangdong Welly Electrical Appliances Co.,Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Emerson Radio Corp. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent and Applicant Information: Name: Emerson Radio Corp. Address: 959 Route 46 East, Suite 210, 2nd Floor, Parsippany, NJ 0 7054 United States FRN: 0026321828 Tel.: +1(973)4282436 Email: [email protected] Signed by (printed name): Shaun Tam Signature: Appl icant: Guangdong Welly Electrical Appliances Co.,Ltd Address: Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, P. R. China FRN: 0019939883 Tel: +86 0760-22507015 Email: [email protected] Signed by (printed name): Yanjun Gao Signature:

Guangdong Welly Electrical Appliances Co., Ltd Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, China Tel: +86 0760-22507015 Email: [email protected] QA-FR-170-B 7/29/2014 Date: 2025-12-8 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization i To whom it may concern: We Guangdong Welly Electrical Appliances Co.,Ltd the undersigned, hereby authorizes Bay Area Compliance Laboratories Corp.(Shenzhen) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp.(Shenzhen) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Printed Name: Gao Yanjun Title: Engineer

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-EXP Page 1 of 4 EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-EXP Page 2 of 4 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-EXP Page 3 of 4 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-EXP Page 4 of 4

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2501Z12554E-EM EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 1 of 9 EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 2 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 3 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 4 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 5 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 6 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 7 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 8 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-INP Page 9 of 9

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-00 TR-EM-RF027 Page 11 of 33 Version 3.0 FCC §18.313, §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE Applicable Standard According to §1.1310, radio frequency devices shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. Calculation formula: Prediction of power density at the distance of the applicable MPE limit S = PG/4πR² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); For simultaneously transmit system, the calculated power density should comply with: Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-00 TR-EM-RF027 Page 12 of 33 Version 3.0 Measurement Environmental Conditions Temperature: 24 °C Relative Humidity: 36 % ATM Pressure: 101.6 kPa The testing was performed by Alex Yan on 2025-11-27. Radiation leakage was measured in the as-received condition with the oven door closed using a microwave leakage meter. A 275ml water load was placed in the center of the oven and the oven was operated at maximum output power. 1 There was no microwave leakage exceeding a power level of 0.2 mW/cm 2 observed at any point 5cm or more from the external surface of the oven. A maximum of 1.0mW/cm 2 is allowed in accordance with the applicable Federal Standards. Hence, microwave leakage in the as-received condition with the oven door closed was below the maximum allowed. Result: Complied.

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF027 Page 1 of 33 Version 3.0 TEST REPORT Applicant Name: Guangdong Welly Electrical Appliances Co., Ltd Address: Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, China Report Number: 2501Z12554E-EM-00 FCC ID: YI4DWF20UXP33 Test Standard (s) FCC PART 18 Sample Description Product Type: Microwave Oven Model No.: F20UXP33-A70 Multiple Model(s) No.: N/A Trade Mark: N/A Date Received: 2025/11/19 Issue Date: 2025/12/09 Test Result: Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Joson Xiao Moon Liu EMC Engineer EMC Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-00 TR-EM-RF027 Page 2 of 33 Version 3.0 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 3 GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 5 OPERATING CONDITION/TEST CONFIGURATION .......................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 6 SPECIAL ACCESSORIES ................................................................................................................................................. 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 6 EXTERNAL CABLE LIST AND DETAILS ......................................................................................................................... 6 CONFIGURATION OF TEST SETUP ................................................................................................................................. 6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULT ................................................................................................................................. 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC §18.313, §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE ......................................................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 MEASUREMENT .......................................................................................................................................................... 12 CONDUCTED EMISSIONS ...................................................................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 EUT SETUP ................................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ....................................................................................................................................... 13 TEST PROCEDURE ...................................................................................................................................................... 14 TEST DATA ................................................................................................................................................................ 14…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-TSP Page 1 of 5 EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-TSP Page 2 of 5 Radiated Emissions Front View (Below 30MHz) Radiated Emissions Rear View (Below 30MHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-TSP Page 3 of 5 Radiated Emissions Front View (Below 1 GHz) Radiated Emissions Rear View (Below 1 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-TSP Page 4 of 5 Radiated Emissions Front View (1-18 GHz) Radiated Emissions Rear View (1-18 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2501Z12554E-EM-TSP Page 5 of 5 Radiated Emissions Front View (Above 18 GHz) Radiated Emissions Rear View (Above 18 GHz)