YJW-12197PGMagnetic Wireless Charging Power Bank

WIRELESS PORTABLE BATTERY Batería portátil inalámbrico Specs •USB-C ™ Input: 18W Power Delivery •USB-C Output: 20W Power Delivery •Wireless Output: up to 15W Caution DO NOT place any credit cards or other types of magnetic material near the charging pad. Do not attempt to disassemble the wireless charging pad as it may short circuit or damage the product. Keep at least 8” (20cm) distance between implantable medical devices such as pacemakers, cochlear implants, etc. Keep this product in a dry and ventilated space. Do not place in direct heat or use in high humidity environments. Do not use organic solvents to clean surface. Instructions Charging your PureJuice 10K Magnetic Wireless Portable Charger using a wall charger, car charger, or computer: 1.Use the provided USB-C to USB-C cable and insert the USB-C connector into the USB-C port on the charger. 2. Plug the USB-C int o your existing wall charger, car charger or computer. The LED will display the percentage of battery remaining and the number will flash to indicate the battery is charging. NOTE: Charging times vary based on the charging method and output power. Checking your current power level: The percentage displayed on the LED means how much battery is remains on the PureJuice Pocket PRO. Charging your device via cable: Using the appropriate USB-C charging cable for your device, insert the USB-C connector into the USB-C port of the charger and connect to your device via the corresponding connector. Charging will automatically begin. To charge your device wirelessly: Place the PureJuice 10K Magnetic Wireless Portable Charger onto the back of your MagSafe ® device until it automatically aligns and snaps into place. Charging will begin automatically. * Works with MagSafe cases. Non-MagSafe cases must be removed before charging. FCC Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy; if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into and outlet on a circuit different form that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. Limited Lifetime Warranty This product is fully warranted against defects in materials and workmanship for the lifetime of the product, so long as the manufacturer continues to make this product. If a product fails due to a manufacturing defect, we will replace it upon proper proof of purchase by the original purchaser. Replacement product will be subject to shipping and handling charges. Damages through normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God, are not covered by this warranty. For all warranty claims, the product must be returned in accordance with PureGear’s return policy. USB-C is a trademark of USB Implementers Forum. The “Qi2” symbol is a trademark of the Wireless Power Consortium. MagSafe is a trademark of Apple Inc., registered in the U.S. and other countries. All rights reserved. All trade names are used for reference purposes only and are the property of their respective owners. Especificaciones •Entrada USB-C: 18W Tecnología Power Delivery •Salida USB-C: 20W Tecnología Power Delivery •Salida inalámbrica: hasta 15W Precaución NO coloque tarjetas de crédito u otros tipos de materiales magnéticos cerca de la base de carga. No intente desensamblar la base de carga inalámbrica pues esto podría causar un cortocircuito o dañar el producto. Mantenga a una distancia mínima de 20 cm (8”) entre dispositivos médicos implantables como marcapasos, implantes cocleares, etc. Mantenga este producto en un lugar seco y ventilado. No lo coloque cerca del calor directo ni lo use en ambientes con un nivel alto de humedad. No use solventes orgánicos para limpiar la superficie. Instrucciones: Para cargar el PureJuice 10K utilizando un CARGADOR DE PARED, CARGADOR DE COCHE o COMPUTADORA: 1.Utilice el cable USB-C a USB-C incluido e inserte el conector USB-C en el puerto de la batería. 2. C onecte el extremo USB-C en su cargador de pared, cargador de coche o computadora. La pantalla LED mostrará el porcentaje de batería restante y el número parpadeará para indicar que la batería se está cargando. NOTA: Los tiempos de carga varían según el método de carga y la potencia de salida. Para ver el nivel de energía actual: El porcentaje que se muestra en la pantalla LED significa la cantidad de energía que le queda en la batería del PureJuice Pocket PRO. Para cargar su dispositivo por cable: Usando el cable de carga USB-C apropiado para su dispositivo, inserte el conector USB-C en el puerto USB-C de la batería y conéctelo a su dispositivo a través del conector correspondiente. La carga iniciará automáticamente. Para cargar su dispositivo d…

Text truncated - open the document above for the full version.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: Superior communications . Address: 5027 Irwindale Ave, Suite 900 Irwindale Ave California United States FRN: 0019944727 Contact Name: George Chen Telephone No: 818-636-4985 E-mail: [email protected] This letter is to confirm that the US Agent for Service of Process accepts responsibility to act as a local representative on behalf of Superior communications . The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Applicant: Company Name: Superior communications . Product Description: Magnetic Wireless Charging Power Bank FRN: 0019944727 Grantee Code: YJW FCC ID: YJW-12197PG Contact Name: George Chen Address: 5027 Irwindale Ave, Suite 900 Irwindale Ave California United States Telephone No: 818-636-4985 E-mail: [email protected] The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. This Agreement is valid until (Permanently valid). Date: 2026/1/20 Applicant’s Name: Superior communications . US Agent for Service of Process’s Name: Superior communications . Title: VP Product Development Title: VP Product Development Signature Signature

Rev 1/26/2023 Superior communications . Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jan. 30, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: YJW-12197PG [Superior communications .] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Superior communications .] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) George Chen Rev 1/26/2023 Superior communications . Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jan. 30, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: YJW-12197PG [Superior communications .] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) George Chen

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Superior communications . Date: Jan. 30, 2026 Product Model Number: 12197PG FCC ID: YJW-12197PG To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: VP Product Development Email: [email protected] Telephone: 818-636-4985 On behalf of: Superior communications .

Superior communications . Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January 30, 2026 Subject; Request for Confidentiality FCC ID: YJW-12197PG To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: George Chen Title: VP Product Development

Page1of4 东莞市金赞智能科技有限公司 DONGGUAN KIMCHEN INDUSTRY INTL LIMITED Address: No.2, Xisha Road, ShijieTown, Dongguan City Tel：86-076986018114 Fax ： 86-076986015646 Http://www.jzcoil.com文件编号FilNo: KC-JZ-09-008 产 品规格书 PRODUCT SPECIFICATION 拟制 PREPARED BY 跟单员 MERCHANDISER 工程审核 ENGINEER CHECKED BY 批准 APPROVED BY Wang zhenwei 客 户： Shenzhen Beilike Technology Co., Ltd. CUSTOMER:____________________________________________________________________ 客户料号： 3-122DX01010AA-160 CUST P/N:____________________________________________________________________ 金赞料号： J30-000920-001 K C P/N:____________________________________________________________________ 产品型号：20.5*38*0.08*55P*11TS*70MM D E S E : 日 期：2025.12.10 D A T E :____________________________________________________________________ 版 本：A.0 VERSION :____________________________________________________________________ （客户承认受领印）ACCEPTANCE STAMP Pageof4 东莞市金赞智能科技有限公司 DONGGUANKIMCHENINDUSTRYINTL LIMITED 3-122DX01010AA-160 20.5*38*0.08*55P*11TS*70MM 拟制 PREPAREDBY 工程审核 ENGINEERCHECKEDBY 2 版本 Rev. 变更前 BeforeChange 变更后内容 DESCRIPTION(ContentOr ReasonForChanged) 日期 Date 修订者 Revisor A.0--新发行（InitialRelease）2025/12/10 Wang Zhenwei Wang Zhenwei li jin Page of4 东莞市金赞智能科技有限公司 DONGGUAN KIMCHEN INDUSTRY INTL LIMITED 3-122DX01010AA-160 20.5*38*0.08*55P*11TS*70MM 拟制 PREPARED BY 工程审核 ENGINEER CHECKED BY 3 1. 产品外形尺寸（OVERALL DIMENSIONS OF PRODUCTS): 单位(Unit):毫米(mm) PS: 1. (E) represents the length of the external magnetic lead; 2. (H) includes the inlet but excludes the release paper; 圈数 Turns 线径 Wire Dia. 绕线方式 疏/ 密 Wdg. Type Spred/Close 绕线方向 Wdg.Direction 相交 是/ 否 Intersect Yes/Not 线圈 正/反贴 Coil Positive/Anti Paste 11TS 0.08*55P 热风绞线 （Stranded wire） 密绕（Close） 逆时针 （Anticlockwise） 是（Yes）反贴（Anti/Paste） ABCDEFGH 18±0.520.5±0.538±143+0/-170±23±10.75±0.11.9MAX Wang Zhenwei li jin Page of4 东莞市金赞智能科技有限公司 DONGGUAN KIMCHEN INDUSTRY INTL LIMITED Address:东莞市石碣镇西沙路2号Tel：86-076986018114 Fax：86-076986015646 Http://www.jzcoil.com文件编号FilNo: KC-JZ-09-008 3-122DX01010AA-160 20.5*38*0.08*55P*11TS*70MM 拟制 PREPARED BY 工程审核 ENGINEER CHECKED BY 4 All materials must meet the ROHS standards. 2. 电气特性（ELECTRICAL CHARACTERISTICS): 温度 TEMPERATURE:25±10°C,湿度 RELATIVE HUMIDITY:65±10% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS 1INDS-F Coil with magnetic sheet：8.2uH±5% 100kHz/1VLCZ METER 1062 2DCRS-F value of resistance： 85mΩMAX LCZ METER 1062 3 Qvalue S-F Qvalue：55MIN 100kHz/1VLCZ METER 1062 3.材料清单（BILL OF MATERIAIS): 序号 NO. 材料名称 Material name 品名描述 Description 物料代码 Material Code 厂商代码 Vendor code 1 wire rod 0.08 * 55P hot air twisted wire / / 2 ferrite Hard magnetic G42.9*5.2*0.5H with holes and slots GCP-T-00581LX 3 Small magnetic core 18*0.5H GCP-T-00181 LX 4 Small double-sided adhesive tape Round double-sided adhesive tape 15*0.08H with tear-off handle SMJ-T-0056HWD 5 Double-sided adhesive tape Circular 36*0.12H with tearable 3M 9448A SMJ-3M-00155 FL 6 tin bar Environmentally friendly lead-free solder wire Lead-free high-temperature solder wire XC 7 glue JS-E7202 (Thickened) White Adhesive E7202WHZY 8 high-temperature adhesive tape High-temperature adhesive tape 3mm High-temperature adhesive tape 3mm 9 Round matte black film Round matte black film, 40*0.05H SMJ-PET-00106 MYS Wang Zhenwei li jin Wang Zhenwei li jin

Ext Photos Model: 12197PG Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 7 Photo 9

产品配色与工艺说明图 Product Colour,Material & Finishing Specfications 3.7mm 5mm Center 4mm Each order has a different batch number Corresponding plane Corresponding plane

Int Photos Model: 12197PG Photo 1 Photo 2 Photo 3 Photo 4 ANT Photo 5

- Page 1 of 12 - Report No.: HB20260113008E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: Magnetic Wireless Charging Power Bank Trade Mark: Puregear Model Number: 12197PG FCC ID: YJW-12197PG Prepared for Superior communications. 5027 Irwindale Ave, Suite 900 Irwindale Ave California United States Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 12 - Report No.: HB20260113008E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 TEST FACILITIES AND ACCREDITATIONS ............................................................................................................ 7 2.1 TEST LABORATORY ..................................................................................................................................................... 7 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 7 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 7 2.4 TEST SOFTWARE ........................................................................................................................................................ 7 3 LIST OF TEST EQUIPMENT ................................................................................................................................ 8 4 RF EXPOSURE .................................................................................................................................................. 9 4.1 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................................................. 9 4.1.1. Limit ............................................................................................................................................................ 9 4.1.2. Test Procedures ........................................................................................................................................... 9 4.1.3. Test Setup .................................................................................................................................................... 9 4.1.4. Test Result ................................................................................................................................................. 10 5 PHOTOGRAPHS OF THE TEST SETUP............................................................................................................... 12 - Page 3 of 12 - Report No.: HB20260113008E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Superior communications. Address ................................. : 5027 Irwindale Ave, Suite 900 Irwindale Ave California United States Manufacturer's Name .......... : Shenzhen Powerqi Technology Co., Ltd. Address ................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang Community, Longgang District, Shenzhen City Product description Product name ........................ : Magnetic Wireless Charging Power Bank Model Number ....................... : 12197PG Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 680106 D01 Wireless Power Transfer v04 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ............................................ : Date (s) of performance of tests ............. : Jan. 21, 2026~Jan. 30, 2026 Test Result ............................................... : Pass Testing Engineer : (Zoe Su) Technical Manager : ( G a r y Lu) Authorized Signatory : (L e o S u) - Page 4 of 12 - Report No.: HB20260113008E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Revision History Revised No. Date of Issue Description 01 Jan. 30, …

Text truncated - open the document above for the full version.

- Page 1 of 35 - Report No.: HB20260113008E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product: Magnetic Wireless Charging Power Bank Trade Mark: Puregear Model Number: 12197PG FCC ID: YJW-12197PG Prepared for Superior communications. 5027 Irwindale Ave, Suite 900 Irwindale Ave California United States Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 35 - Report No.: HB20260113008E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 6 1.4 POWER SETTING CONFIGURATION PARAMETERS ............................................................................................................... 6 1.5 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 SUMMARY OF TEST RESULT ............................................................................................................................. 7 3 TEST FACILITIES AND ACCREDITATIONS ............................................................................................................ 8 3.1 TEST LABORATORY ..................................................................................................................................................... 8 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 8 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 8 3.4 TEST SOFTWARE ........................................................................................................................................................ 8 4 LIST OF TEST EQUIPMENT .............................................................................................................................. 10 5 TEST ITEM AND RESULTS ............................................................................................................................... 12 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 12 5.2 CONDUCTED EMISSION ............................................................................................................................................. 13 5.3 RADIATED EMISSION ................................................................................................................................................ 17 5.4 OCCUPIED BANDWIDTH ............................................................................................................................................ 25 6 PHOTOGRAPHS OF THE TEST SETUP............................................................................................................... 27 7 PHOTOGRAPHS OF THE EUT .......................................................................................................................... 30 - Page 3 of 35 - Report No.: HB20260113008E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Superior communications. Address ................................. : 5027 Irwindale Ave, Suite 900 Irwindale Ave California United States Manufacturer's Name .......... : Shenzhen Powerqi Technology Co., Ltd. Address ................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang Community, Longgang District, Shenzhen City Product description Product name ........................ : Magnetic Wireless Charging Power Bank Model Number ....................... : 12197PG Standards ............................. : FCC Part 15C Test procedure ....................... : IEEE/ANSI C63.10-2020 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ............................................ : Date (s) of performance of tests ............. : Jan. 21, 2026~Jan. 30, 2026 Test Result ............................................... : Pass Testing Engineer : (Zoe Su) Technical Manager : (G a r y L u) Authorized Signatory : (L e o S u) - Page 4 of 35 - Report No.: HB20260113008E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID…

Text truncated - open the document above for the full version.

Photographs of the Test Setup Model: 12197PG Radiated Emission Below 30MHz Radiated Emission Above 30MHz Conducted Emission MPE