YN3-01007001WIRELESS TRANSMITTER-EMITTER

User’s Manual – BC5100 System: BC5000 Glasses and BC100 Emitter BC100 3D Emitter Manual The BC100 3D Emitter connects a 3D-Ready TV to the BC5000 LCD Shutter Glasses for the ultimate in 3D stereoscopic viewing. This document describes the features, connection, setup, and operation of the BC100 3D Emitter. Features RF synchronization for uninterruptable 3D glasses performance Ready to watch compatibility with 3D Ready TVs equipped with a 3D Emitter Port IR sync learning capability for use with IR 3D sync based frame sequential 3D Ready TVs LED indicators assist with IR Sensor placement Management Software enables Upgrade functionality for compatibility with future 3D TVs Manual performance adjustment capability Connections 3D Ready TV with 3D Emitter Port 1: Connect the emitter to the TV using the 3D Glasses Emitter/3D SYNC Out Port as shown below. Place the BC100 3D Emitter behind the TV. 3D Ready TV with IR Emitter 1. Connect the included BC010 IR sensor to the BC100 3D Emitter. Place the IR sensor in the approximate locations shown in the image below – see the section 3D Ready TV with IR Emitter for proper placement of the IR sensor. 2. Power the BC100 3D Emitter using USB port on the 3D Ready TV. 1 : B C 0 1 0 I R S e n s o r ( s u p p l i e d ) Back or Side of TV 2: USB A to Micro B Cable (Supplied) Basic Features RF Communication of Synchronization Signal RF communications enables the BC5100 3D System to provide an awesome and uninterruptable 3D viewing experience. Line of sight obstructions, emitter placement and viewer seating arrangements have no impact on the performance of the emitter to glasses synchronization. Optimal seating distance and viewing angle is determined by the capabilities of the 3D Ready TV coupled to the BC5100 3D System. LED Indicators The BC100 3D Emitter uses 5 multicolored LEDs to indicate modes of operation or other information. The LEDs are located on the top of the emitter close to the joystick and display red, green, or orange. Joystick The BC100 3D Emitter uses a joystick to allow the user to enable various modes and change settings. The joystick has two axes and a center button function. Function of the axes and buttons are dependent on the operating mode as described in following sections. Modes of Operation The BC100 3D Emitter has 5 modes of operation. Normal IR Signal Strength Manual Tuning of Glasses Performance Pairing the BC100 with BC5000 Glasses IR Signal Search and Learning Accessing Modes During normal operation, the joystick is used to access different modes of operation. Press and hold the joystick to cycle through the available modes. Release the joystick to select a mode. In any mode, the normal mode of operation resumes after 60 seconds of inactivity. Normal Operation During normal operating mode, the BC100 3D Emitter interprets 3D signals from the TV and controls the BC5000 Series LCD Shutter Glasses through RF. No LEDs are active. IR Signal Strength Indicator The signal strength indicator provides a visual IR signal quality measurement. The number of lit green LEDs indicates the quality of the IR signal, with more green LEDs equating to better IR reception. Use this mode to determine the ideal location for placement of the IR sensor. Manual Performance Tuning The BC100 3D Emitter and BC5000 LCD Shutter Glasses are preprogrammed to work with a wide variety of TVs and 3D content. The manual performance tuning mode enables the 3D system performance to be fine tuned. Warning, use of this feature can result in improper or undesirable operation. 3D Emitter & Glasses Pairing In environments where more than one BC100 3D Emitter is present, BC5000 glasses should be paired with the emitter to ensure proper operation. This mode also involves the BC5000 glasses and is described in greater detail in a subsequent section. IR Signal Search and Learn This mode is active when the device is powered on for the first time, after a Factory Defaults reset, or when enabled using the joystick mode access. Once the BC100 3D Emitter identifies and learns a 3D IR signal, the startup sequence will only look for the previously identified IR signal. To have the BC100 3D Emitter search and learn the signals from another TV, use this mode. Factory Defaults In the event that the BC100 3D Emitter is not working properly and other troubleshooting methods have failed, use the Reset to Factory Defaults mode to attempt recovery of proper operation. Warning: Any tuning done using Manual Performance Tuning will be erased. Using the BC100 3D Emitter with 3D Sync Port Equipped TVs Use the guide in Connections: 3D Ready TV with 3D Emitter Port to properly connect the BC100 3D Emitter. When the TV is turned on, the BC100 3D Emitter will turn on as well. The LEDs will display a red moving pattern while the emitter is attempting to acquire a 3D signal and until a signal is found. If the emitter searches for a signal for longer than 60 seconds, a signal is not found. Ensure that the TV is in 3D mode. Upon finding a 3D signal, all LEDs will turn green for approximately 60 seconds and then turn off. Once the LEDs indicate a 3D signal, the BC5000 glasses can be used to experience 3D. The BC100 3D Emitter is preprogrammed and configured to operate with Sync Port equipped TVs. If the image when viewed through the BC5000 glasses is fuzzy, has ghosting, or is out of polarity, see Using the Joystick to Manually Tune Performance. Using the BC100 3D Emitter with IR 3D Sync Equipped TVs Connect the emitter and BC010 IR sensor to the TV as shown in Connections: 3D Ready TV with IR Emitter. Turn on the TV and enable 3D display. Hold the IR sensor below the TV while viewing the LEDs. While searching for and learning an IR sync signal, the LEDs will display a red moving pattern. The BC100 3D Emitter will stay in IR search mode until a signal is found and learned. If the emitter stays in search mode for longer than 60 seconds, a signal has not been located. Ensure that the TV is in 3D mode. When…

Text truncated - open the document above for the full version.

1411 NW 7 th Road Gainesville, Fl 32603 1-352-870-3799 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: YN3-01007001. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type Block Diagram Schematics Operational Description File Name The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Robert Mentz CFO

1411 NW 7 th Road, Gainesville, FL 32603 Ph 1-352-870-3799 www.bitcauldron.com September 14, 2010 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Re.: Limited Module Approval for YN3-01007001 To Whom It May Concern: We, Bit Cauldron Corporation, hereby request a Limited Module Approval as provided in Section 15.212 of the FCC Rules. The requirements of this section have been fulfilled as follows: 15.212(a)(1)(i): Requirement of RF Shielding: The module meets radiated emissions limits of part 15 of the FCC Rules. However the module does not require or have its own RF shielding. This will need to be provided by the device into which it is installed as required. 15.212(a)(1)(ii): Requirement of Buffered Input: The module incorporates buffered inputs which meet the requirements. 15.212(a)(1)(iii): Requirement of Power Supply Regulation: The module incorporates its own regulators, which meets the requirements. 15.212(a)(1)(iv): Antenna Requirement: The module incorporates a permanently attached antenna. 15.212(a)(1)(v): Stand-Alone Test Configuration: The module was tested in a stand-alone test configuration as described in the test report. 15.212(a)(1)(vi)(A): Labeling Requirement: The module will be labeled with its own FCC identification number, and the device into which the module is installed will display a label referring to the enclosed module. A picture of the label is included in the documentation. 15.212(a)(1)(vii): Operating Requirements: The module meets the specific rules for this type of transceiver, and the User’s Manual contains instructions for maintaining compliance. 15.212(a)(1)(vii): RF Exposure: The module complies with RF exposure requirements as demonstrated in the test report. Sincerely, Robert Mentz CFO Bit Cauldron Corporation Ph 1-610-504-7813

APPLICANT: BIT CAULDRON CORP. FCC ID: YN3-01007001 EXTERNAL PHOTOS

Updated Product Markings with new Monster Model Identification Figure 1. Example Marking for Monster version of Bit Cauldron's BC5000 Figure 2.Example Marking for Monster version of Bit cauldron's BC100

APPLICANT: BIT CAULDRON CORP. FCC ID: YN3-01007001 INTERNAL PHOTOS

QuantityDescriptionDesignatorManufacturer 1Manufacturer Part Number 1Supplier 1Supplier Part Number 1 2 CAP CER .1UF 10V 10% X5R 0402C1, C6 Murata Electronics North AmericaGRM155R61A104KA01DDigi-Key490-1318-2-ND 2 CAP CER 47PF 50V 5% C0G 0402C2, C8 Murata Electronics North AmericaGRM1555C1H470JZ01DDigi-Key490-1287-2-ND 3 CAP CER 220PF 50V 5% C0G 0402C3, C14, C16 Murata Electronics North AmericaGRM1555C1H221JA01DDigi-Key490-1293-2-ND 1 CAP CER 10UF 6.3V X7R 10% 0805C4Taiyo YudenJMK212B7106KG-TDigi-Key587-2396-2-ND 3 CAP CER 10000PF 16V 10% X7R 0402C5, C15, C17 Murata Electronics North AmericaGRM155R71C103KA01DDigi-Key490-1313-2-ND 1 CAP CERAMIC 150PF 50V NP0 0402C11YageoCC0402JRNP09BN151Digi-Key311-1025-2-ND 1 CAP CER 1.0UF 6.3V 10% X5R 0402C12 Murata Electronics North AmericaGRM155R60J105KE19DDigi-Key490-1320-2-ND 1 PHOTODIODE BLU W/ DF 4.1MM T1 3/ 4D2Advanced Photonix IncPDB-C139FDigi-KeyPDB-C139F-ND 4 IC DIODE FAST SW 75V SOD-523F - 1N914BWTD3, D4, D5, D6Fairchild Semiconductor1N914BWTDigi-Key1N914BWTTR-ND 3 RES 0.0 OHM 1/ 16W 1% 0402 SMDL1, L2, L3Vishay / DaleCRCW 04020000Z0EDDigi-Key541-0.0JTR-ND 1 INDUCTOR POWER 1000UH 1007L4Taiyo YudenCB2518T102KDigi-Key587-2195-2-ND 2 TRANS NPN 50V 150MA SOT-323Q1, Q2Rohm Semiconductor2SD2351T106WDigi-Key2SD2351T106WTR-ND 2 RES 2.32M OHM 1/ 16W 1% 0402 SMDR1, R3Vishay/ DaleCRCW 04022M32FKEDDigi-Key541-2.32MLTR-ND 1 RES 1.00M OHM 1/ 16W 1% 0402 SMDR2Panasonic - ECGERJ-2RKF1004XDigi-KeyP1.00MLTR-ND 1 RES 27.0K OHM 1/ 16W 1% 0402 SMDR4Rohm SemiconductorMCR01MZPF2702Digi-KeyRHM27.0KLTR-ND 2 RES 100K OHM 1/ 16W 1% 0402 SMDR5, R13YageoRC0402FR-07100KLDigi-Key311-100KLRTR-ND 1 RES 3.00K OHM 1/ 16W 1% 0402 SMDR6Vishay/ DaleCRCW 04023K00FKEDDigi-Key541-3.00KLTR-ND 4 RES 1.00K OHM 1/ 16W 1% 0402 SMDR7, R12, R15, R20YageoRC0402FR-071KLDigi-Key311-1.00KLRTR-ND 1 RES 68.0 OHM 1/ 16W 1% 0402 SMDR8YageoRC0402FR-0768RLDigi-Key311-68.0LRTR-ND 3 Res 10.0K 0402R9, R10, R11YageoRC0402FR-0710KLDigi-Key311-10.0KLRTR-ND 1 RES 5.62K OHM 1/ 16W 1% 0402 SMDR14YageoRC0402FR-075K62LDigi-Key311-5.62KLRTR-ND 1 RES 510 OHM 1/ 16W 1% 0402 SMDR17YageoRC0402FR-07510RLDigi-Key311-510LRTR-ND 1 RES 330K OHM 1/ 10W 1% 0402 SMDR18Panasonic - ECGERJ-2RKF3303XDigi-KeyP330KLTR-ND 1 RES 2.70K OHM 1/ 16W 1% 0402 SMDR19YageoRC0402FR-072K7LDigi-Key311-2.70KLRTR-ND 3 RES 0.0 OHM 1/ 16W 1% 0402 SMDR21, R22, R23Vishay / DaleCRCW 04020000Z0EDDigi-Key541-0.0JTR-ND 1 LinCMOS Precision Dual Operational AmplifierU1Texas InstrumentsTLC272CPWRDigi-Key296-7354-2-ND 1 Push-Pull Output Sub-Microamp Comparator, 5-Pin SC-70, Industrial Temperature, Tape and ReelU2Microchip TechnologyMCP6541T-I/LTDigi-KeyMCP6541T-I/LTTR-ND QuantityDescriptionDesignatorManufacturer 1Manufacturer Part Number 1Supplier 1Supplier Part Number 1 2 RES 1.00K OHM 1/ 16W 1% 0402 SMDR13, R19YageoRC0402FR-071KLDigi-Key311-1.00KLRTR-ND 1 RES 1.00M OHM 1/ 16W 1% 0402 SMDR20Panasonic - ECGERJ-2RKF1004XDigi-KeyP1.00MLTR-ND 1 RES 2.00M OHM 1/ 16W 1% 0402 SMDR16Vishay/ DaleCRCW 04022M00FKEDDigi-Key541-2.00MLTR-ND 2 3.6V Zener SOD-523D3, D7 Fairchild SemiconductorMM5Z3V6Digi-KeyMM5Z3V6TR-ND 2 CAP CERM 10PF 50V C0G 0402C17, C18Taiyo YudenUMK105CG100DV-FDigi-Key587-1947-2-ND 5 Res 10.0K 0402 R2, R3, R8, R9, R10YageoRC0402FR-0710KLDigi-Key311-10.0KLRTR-ND 2 Res 56.0K 0402R1, R6YageoRC0402FR-0756KLDigi-Key311-56.0KLRTR-ND 1 Balun CC2530 2450BM15A0002B1 Johanson Technology Inc2450BM15A0002Digi-Key2450BM15A0002-ND 7 CAP CER .1UF 10V 10% X5R 0402 C4, C5, C7, C10, C12, C13, C14 Murata Electronics North AmericaGRM155R61A104KA01DDigi-Key490-1318-2-ND 4 CAP CER 1.0UF 6.3V 10% X5R 0402C1, C2, C15, C16 Murata Electronics North AmericaGRM155R60J105KE19DDigi-Key490-1320-2-ND 1 CAP CER 2.2UF 4V X5R 0402C3 Murata Electronics North AmericaGRM155R60G225ME15DDigi-Key490-4518-2-ND 2 CAP CER 47PF 50V 5% C0G 0402C8, C9 Murata Electronics North AmericaGRM1555C1H470JZ01DDigi-Key490-1287-2-ND 1 CAP CER 220PF 50V 5% C0G 0402C11 Murata Electronics North AmericaGRM1555C1H221JA01DDigi-Key490-1293-2-ND 1 Cap SMD 1pF 0402 HFC6 Johanson Technology Inc500R07S1R2BV4TDigi-Key712-1268-2-ND 1 System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 USBU1Texas InstrumentsCC2531F256RHARDigi-KeyCC2531F256RHAR-ND 1 Chip Antenna 18pkgE1 Johanson Technology Inc2450AT18B100EDigi-Key712-1006-2-ND 1 EVQQ7 Multifunction SwitchS1Panasonic - ECGEVQ-Q7GA50Digi-KeyP13351STR-ND 1 FILTER CHIP 1000 OHM 250MA 0402L1 Murata Electronics North AmericaBLM15HG102SN1DDigi-Key490-3999-2-ND 5 BiColor LED 0603 SMDD2, D5, D6, D8, D9 Avago Technologies US Inc.HSMF-C165Digi-Key516-1419-2-ND 1 Ind 2.7nH 0402 HFL3 Johanson Technology IncL-07C2N7SV6TDigi-Key712-1415-2-ND 1 Ind 3.3nH 0402 HFL2 Johanson Technology IncL-07C3N3SV6TDigi-Key712-1416-2-ND 1 SMT AUDIO JACK W/ 4 CONDUCTORS 3.5mmJ3CUI IncSJ-43514-SMTDigi-KeyCP-43514SJTR-ND 1 RES 1.5K OHM 1/ 16W 1% 0402 SMDR7 Stackpole Electronics IncRMCF 1/ 16S 1.5K 1% RDigi-Key RMCF1/ 16S1.5KFRTR- ND 2 RES 33.0 OHM 1/ 16W 1% 0402 SMDR4, R5YageoRC0402FR-0733RLDigi-Key311-33.0LRTR-ND 10 RES 390 OHM 1/ 16W 1% 0402 SMD R11, R12, R14, R15, R17, R18, R21, R22, R23, R24Vishay/ DaleCRCW 0402390RFKEDDigi-Key541-390LTR-ND 2 SCHOTTKY RECT 20V 0.5A SOD323FD1, D4 NXP SemiconductorsPMEG2005EJ,115Digi-Key568-4110-2-ND 1 IC LDO REG ADJ 50MA MCPWR SC70-5U2Texas InstrumentsTPS71501DCKRDigi-Key296-12957-2-ND 1 USB 2.0, Right Angle, SMT, Micro B Type, ReceptacleJ2 Molex Connec tor Corporation47346-0001Digi-KeyWM17141TR-ND 1 CryCRYSTAL 32.000000 MHZ SMD 10PFY1NDKNX2520SA-32.000000MHZDigi-Key644-1065-2-ND

FCC PART 15.249 AND IC RSS-210 TEST REPORT UNLICENSED INTENTIONAL RADIATOR Applicant BIT CAULDRON CORPORATION Address 1411 NW 7th Rd GAINESVILLE FL 32603 USA FCC ID YN3-01007001 IC 9186A-01007001 Model Number MV-BC0100, BC100 Product Description WIRELESS TRANSMITTER Date Sample Received 8/23/2010 Date Tested 9/9/2010 Tested By Joe Scoglio Approved By Mario R. de Aranzeta Report Number 1990AT10TestReport.doc Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW State Road 45 Newberry, FL 32669 USA Ph: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: [email protected] Website: www.timcoengr.com Certificate # 0955-01 APPLICANT: BIT CAULDRON CORPORATION FCC ID: YN3-01007001 IC: 9186A-01007001 REPORT: Z:\B\BIT CAULDRON\1990AT10\1990AT10TestReport.doc Page 2 of 13 TABLE OF CONTENTS GENERAL REMARKS ...................................................................................................... 3 GENERAL INFORMATION ............................................................................................... 4 EMC EQUIPMENT LIST .................................................................................................. 5 TEST PROCEDURES ...................................................................................................... 6 RADIATION INTERFERENCE .......................................................................................... 7 OCCUPIED BANDWIDTH ................................................................................................ 8 BAND EDGE COMPLIANCE ............................................................................................ 9 POWER LINE CONDUCTED INTERFERENCE ............................................................... 11 APPLICANT: BIT CAULDRON CORPORATION FCC ID: YN3-01007001 IC: 9186A-01007001 REPORT: Z:\B\BIT CAULDRON\1990AT10\1990AT10TestReport.doc Page 3 of 13 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: 9/9/2010 APPLICANT: BIT CAULDRON CORPORATION FCC ID: YN3-01007001 IC: 9186A-01007001 REPORT: Z:\B\BIT CAULDRON\1990AT10\1990AT10TestReport.doc Page 4 of 13 GENERAL INFORMATION DUT Specification The test results relate only to the items tested. Applicable Standard Part 15.249 DUT Description WIRELESS TRANSMITTER FCC ID YN3-01007001 IC 9186A-01007001 Model Number MV-BC0100, BC100 Operating Frequency TX: 2475.1 RX: Same No. of Channels 1 DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable Antenna Connector Fixed antenna Test Facility Timco Engineering Inc. located at 849 NW State Road 45 Newberry, FL 32669 USA. Test Conditions Temperature: 26ºC Relative humidity: 50% Test Exercise The DUT was placed in continuous transmit mode of operation. Modifications None Test Supporting Equipment Supporting Device Manufacturer Model / FCC ID Serial Number Laptop computer Samsung NP-R480L APPLICANT: BIT CAULDRON CORPORATION FCC ID: YN3-01007001 IC: 9186A-01007001 REPORT: Z:\B\BIT CAULDRON\1990AT10\1990AT10TestReport.doc Page 5 of 13 EMC EQUIPMENT LIST Device Manufacturer Model Serial Number Cal/Char Date Due Date 3-Meter Semi- Anechoic Chamber Panashield N/A N/A Listed 3/10/10 3/10/12 AC Voltmeter HP 400FL 2213A14499 CAL 3/23/09 3/23/11 Antenna: Dipole Kit Electro- Metrics TDA-30/1-4 153 CHAR 6/10/09 6/10/11 Frequency Counter HP 5385A 3242A07460 CAL 5/26/09 5/26/11 Hygro- Thermometer Extech 445703 0602 CAL 1/30/09 1/30/11 Modulation Analyzer HP 8901A 3435A06868 CAL 5/26/09 5/26/11 Digital Multimeter Fluke FLUKE-77-3 79510405 CAL 5/18/09 5/18/11 Analyzer Tan Tower Preamplifier HP 8449B-H02 3008A00372 CAL 11/21/09 11/21/11 Analyzer Tan Tower Quasi- Peak Adapter HP 85650A 3303A01690 CAL 11/22/09 11/22/11 Analyzer Tan Tower RF Preselector HP 85685A 3221A01400 CAL 11/21/09 11/21/11 Analyzer Tan Tower Spectrum Analyzer HP 8566B Opt 462 3138A07786 3144A20661 CAL 11/24/09 11/24/11 Temperature Chamber Tenney Engineering TTRC 11717-7 CHAR 4/25/10 4/25/12 APPLICANT: BIT CAULDRON CORPORATION FCC ID: YN3-01007001 IC: 9186A-01007001 REPORT: Z:\B\BIT CAULDRON\1990AT10\1990AT10TestReport.doc Page 6 of 13 TEST PROCEDURES Radiation Interference: ANSI C63.4-2003 using a spectrum analyzer, a preselector, a quasi- peak adapter, and an appropriate antenna. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The resolution bandwidth was 100 kHz with an appropriate sweep speed and the video bandwidth was 300 kHz up to 1 GHz and 1 MHz with a video BW of 3 MHz above 1 GHz. When an emission was found, the table was rotated to produce the maximum signal strength. The antenna was placed in both the horizontal and vertical planes and the worse case emissions were reported. The spectrum was searched to at least the tenth (10) harmonic of the fundamental. Formula Of Conversion Factors: The field strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units …

Text truncated - open the document above for the full version.