YS2TNETSBC010203Use for NEC large screen LCD Displays

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help

Date: September 27, 2010 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD，5/F, Block 4, Anhua Industrial Zone., No.8 Tai Ran Rd. Che Gong Miao, Fu Tian District, Shenzhen, CHINA.，Hanson Chueng to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Technovare Systems Inc. 1675 Scenic Ave., Suite 200, Costa Mesa, CA, 92626, USA Dated this: September 27, 2010 Agency agreement expiration date: 12 Months By: Grant Stockton Signature Printed Title: President On behalf of: Technovare Systems Inc. Tel No: 714-966-9099, EX 214

September 27, 2010 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: __YS2TNETSBC010203_________ Product Name: Embedded Computer Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this: September 27, 2010 Agency agreement expiration date: 12 Months By: Grant Stockton Signature Printed Title: President On behalf of: Technovare Systems Inc. Tel No: 714-966-9099, EX 214

Technovare Systems, Inc. Model No.: NEC NET-SBC-01/02/03 FCC ID: YS2TNETSBC010203 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions(1) This device may not cause harmful interference,and(2)this device must accept any interference received, Including interference that may cause undesired operation

FCC ID Label Location

The NEC NET-SBC-01/02/03 Operational Description The NEC NET-SBC-01/02/03 is an embedded computer system designed for part of NEC TFT LCD Monitors. It provides an Intel Atom 330 processor coupled to a powerful Nvidia Graphics processor to enable high-definition video processing capabilities. All of interfaces (DVI, 1000BaseT, USB, SATA, PCIe) provide robust interconnect capabilities. Through that 60 pins connector on the computer system, DC16V power provide by the NEC TFT LCD Monitor. Also, DVI, Stereo Audio and RS232 of the computer system’s interfaces are interconnection to the NEC TFT LCD Monitor. The NEC NET-SBC-01/02/03 Computer system must be placed in the plug-in slot on the NEC TFT LCD Monitors, and the plug-in slot is located on the left side of the display near the carrying handle. Use the screws that were previously holding the cover panel in place to secure the computer. Plug-in LAN line to Ethernet port of the computer, and using USB ports of computer to connect your Mouse and Keyboard (if need it). When switch the NEC TFT LCD Monitor on, the LED on the front plate of computer will be flashes, the NEC NET-SBC-01/02/03 computer system is working now. And customer may follow NEC TFT LCD Monitors user manual to operating setting by Remote Control of NEC TFT LCD Monitor. Also, customer may use the Reset button which on the front plate to turn on / off the NEC NET-SBC-01/02/03 computer system by manually. Input Voltage: DC16V, 2A

ISO/IEC17025 Accredited Lab. Report No: FCC 1009019 File reference No: 2010-09-17 Applicant: Technovare Systems, Inc. Product: Embedded Computer Brand Name: ，NEC TNET - PC Model No: NET-SBC-01/02/03 Test Standards: FCC Part 15 Subpart B: 2008 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.4&FCC Part 15 regulations for the evaluation of electromagnetic compatibility Approved By Terry Tong Manager Dated: Sep 17, 2010 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD East 5/Block 4, Anhua Industrial Zone, No.8, Tairan Rd. Chegongmiao, FuTian District, Shenzhen, CHINA. Tel (755) 83448688 Fax (755) 83442996 Report No: 1009019 Page 2 of 116 Date: 2010-09-17 TEST REPORT "The report refers only to the sample tested and does not apply to the bulk production. This report is issued in confidential to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co., Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for illegal purpose. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co., Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co., Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co., Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate." Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2005 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 899988. IC- Registration No.: IC5205A-01 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration IC No.: 5205A-01. VCCI- Registration No.: R-3015 and C-3332 The EMC Laboratory has been registered and fully described in a report filed with the (VCCI) Voluntary Control Council for Interference. The acceptance letter from the VCCI is maintained in our files. Registration IC No.: R-3015 and C-3332 Report No: 1009019 Page 3 of 116 Date: 2010-09-17 TEST REPORT "The report refers only to the sample tested and does not apply to the bulk production. This report is issued in confidential to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co., Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for illegal purpose. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co., Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co., Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co., Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate." Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT ............................................................................................4 1.4 Test Uncertainty................................................................................................ 4 1.5 Submitted Sample............................................................................................. 4 1.6 Test Duration.................................................................................................. 4 2.0 List of Measurement Equipment........................................................................ 5 2.1 Conducted Emission Test..................................................................................... 5 2.2 Radiated electromagnetic disturbance test................................................................. 5 2.3 Auxiliary Equipment.......................................................................................... 5 2.4 I/O Cable....................................................................................................... 5 3.0 Technical Details............................................................................................. 6 3.1 Investigations Requested..................................................................................... 6 3.2 Test Standards..............................................................................................…

Text truncated - open the document above for the full version.

Radiated Emissions Conducted Emissions: