YVDFMG3Asset Tracking Device

FMG-3 User’s Guide December 16, 2011 Cubic Global Tracking Solutions 400 E 16 th Street Panama City, FL 32405 USA http://www.cubic.com/Solutions/Cubic-Global-Tracking-Solutions Cubic Global Tracking Solutions Page 2 of 14 4511144v1d Copyright © 2011 CGTS Notice of Ownership Use of this information shall be limited to persons having a need to know, within the appropriate project organizations, as defined within the nondisclosure agreement (NDA) between Cubic Global Tracking Solutions (Cubic GTS) and its customers. Disclosure of the material in this document to outside organizations shall only be made with the written consent of an authorized Cubic GTS corporate officer. This document contains information that is considered proprietary and confidential to Cubic GTS. No information contained in this document may be released, re-printed, or redistributed without the permission of Cubic GTS. The information contained in this document is subject to change without notice. If you have questions or comments about this document, please direct them to [email protected]. Copyright © 2011 by Cubic GTS Revision History Revision Date Author(s) Notes 1 12/8/11 Bryan Shah Initial draft. Cubic Global Tracking Solutions Page 3 of 14 4511144v1d Copyright © 2011 CGTS FMG-3 USER’S MANUAL Table of Contents 1 REGULATORY COMPLIANCE ........................................................................................................ 4 2 INTRODUCTION ............................................................................................................................... 5 2.1 FIXED MESH GATEWAY (FMG-3) .......................................................................................................... 5 2.2 THE DEVICE MANAGEMENT CENTER ..................................................................................................... 6 2.3 MANAGED ASSET TAGS ............................................................................................................................. 6 2.4 CUBIC GTS MIST™ MESH NETWORK ....................................................................................................... 6 3 FIXED MESH GATEWAY (FMG-3) ............................................................................................... 7 3.1 NOMINAL INSTALLATION .......................................................................................................................... 8 3.2 ETHERNET NETWORK – DHCP ............................................................................................................... 9 3.3 ETHERNET NETWORK – STATIC ADDRESS ............................................................................................ 9 3.4 MOUNTING ............................................................................................................................................... 10 3.5 CONFIGURING THE FMG-3 .................................................................................................................... 10 3.5.1 Console Port .............................................................................................................................................. 10 3.5.2 SSH Session ................................................................................................................................................ 11 3.6 WHAT TO CONFIGURE AND WHY ......................................................................................................... 11 APPENDIX A: SPECIFICATIONS......................................................................................................... 13 APPENDIX B: APPROVED EXTERNAL ANTENNAS ...................................................................... 14 Cubic Global Tracking Solutions Page 4 of 14 4511144v1d Copyright © 2011 CGTS 1 Regulatory Compliance FCC STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Changes or modifications not expressly approved by Cubic Global Tracking Solutions for compliance could void the user’s authority to operate the equipment. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons during normal device operation and must not be located or operating in conjunction with any other antenna or transmitter. This device has been designed to operate with the antennas listed in Appendix A. Antennas not included in this list are prohibited for use with this device without the express approval of Cubic Global Tracking Solutions. Cubic Global Tracking Solutions Page 5 of 14 4511144v1d Copyright © 2011 CGTS 2 Introduction Cubic Global Tracking Solutions’ Fixed Mesh Gateway (FMG-3) is the mist™ mesh network’s primary path to the internet. Managed Assed Tags (MAT) wirelessly communicates to the FMG-3 using the mist™ protocol and the FMG-3 forwards data from those tags through the internet to the Device Management Center (DMC) where the data is stored indefinitely. Figure 1: FMG-3 Network 2.1 Fixed Mesh Gateway (FMG-3) The FMG-3 is the mist™ mesh network’s fastest, lowest-cost path to the internet. The FMG-3 contains a mist™ radio and a hardwired 10/100 Ethernet connection to the internet. These allow the FMG-3 to receive data from MATs and forward it to the DMC, giving the end-user visibility of the state of t…

Text truncated - open the document above for the full version.

Bryan Shah 400 E. 16 th St Panama City, FL 32405 9/26/2011 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR FMG-3, FCC ID: YVDFMG3 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the Schematic, Block Diagrams, Bill of Materials, and Technical Operation documents required to be submitted with this application be permanently withheld from public review. Our product is marketed for DoD applications. It is part of a system that has won the U.S. Army’s Next Generation Wireless Communications (NGWC) contract to monitor and track all goods that the U.S. Army ships. Technical information for this product cannot be released for public inspection. We can’t allow our competitors access to our proprietary information. Much of the technical documentation included with this application is the result of years of engineering. If it were made publicly available, our competitors could use it to bypass all of the NRE we have invested in our product and sell a knock-off for a fraction of the price. Please contact me if there is any information you may need. Sincerely, Bryan Shah

Photograph 1. Antenna Port, EUT View Photograph 2. Antenna Port Photograph 3. Back Photograph 4. Bottom Photograph 5. EUT Photograph 6. Flash Card Bottom Photograph 7. Flash Card Top Photograph 8. Front Photograph 9. Left Photograph 10. Right Photograph 11. Top

02:18 PM1DATE :TIME :PG :OF11/31/2012 Title:38-0088-00 FMG-3 Top Cover Label Author:Bryan Shah Doc Nbr:4511110v4 Releasability: Cubic Global Tracking Solutions, Inc Confidential – File: 38-0088-00_FMG-3_Top_Cover_4511110v5.vsd 2. Actual label may be Black & White MAC address obtained during turn-up testing. Mesh address assigned during final provisioning 2" 1. Label Material: Identco TT700P or equivalent 3. Label consists of 5 ea ¾” by 2" labels 4. Labels shall have rounded corners 5. Inter-label gap is not required 6. Blank/unused first position required in order to tape label to finished product 7. Actual label stock will be blank. Printing to occur at Contract Manufacturer per unit. 2 1/2" 3/4" 1/4" 3/4" 1/4" 3/4" 1/4" 3/4" 1/4" 3/4" Part Number rev will change as required to match build BOM rev. 03-1036-00 r2 YVDFMG3 00004004611 Part #: FCC ID: ` FMG-3 6104 Model: Option: 03-1036-00 r2 YVDFMG3 00005004611 Part #: FCC ID: FMG-3 6104 Model: Option: 03-1036-00 r2 YVDFMG3 00006004611 Part #: FCC ID: FMG-3 6104 Model: Option: 03-1036-00 r2 YVDFMG3 00007004611 Part #: FCC ID: FMG-3 6104 Model: Option:

Photograph 1. Board Removed Photograph 2. Bottom Board (Flash Card Removed) Photograph 3. Bottom Board Photograph 4. Cover Off Photograph 5. Radio Card (Shield Removed) Photograph 6. Radio Card Bottom Photograph 7. Radio Card Top Photograph 8. Top Board Photograph 9. Flash Card Bottom Photograph 10. Flash Card Top

§ 15.247(i) Maximum Permissible Exposure RF Exposure Requirements: §1.1307(b)(1) and §1.1307(b)(2): Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. RF Radiation Exposure Limit: §1.1310: As specified in this section, the Maximum Permissible Exposure (MPE) Limit shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Sec. 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of Sec. 2.1093 of this chapter. MPE Limit Calculation: EUT’s operating frequencies @ 2400-2483.5 MHz; highest conducted power = 2.132 dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 5.5 dBi. Equation from page 18 of OET 65, Edition 97-01 S = PG / 4 2 or where, S = Power Density (1 mW/cm 2 ) P = Power Input to antenna (1.63mW) G = Antenna Gain (3.55 numeric) R = (1.63*3.55/ 4*3.14*1.0) 1/2 = (5.80 / 12.56) 1/2 = 0.68cm S = 1.63*3.55/ 4*3.14*20 2 = 5.80 /5024 = 0.0012mW/cm 2

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230-3432 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 33439 WESTERN AVENUE ● UNION CITY, CALIFORNIA 94587 ● PHONE (510) 489-6300 ● FAX (510) 489-6372 3162 BELICK STREET ● SANTA CLARA, CALIFORNIA 95054 ● PHONE (408 748-3585 ● FAX (510) 489-6372 The Nation’s First Licensed Nationally Recognized Testing Laboratory February 2, 2012 Cubic Global Tracking Solutions 2560 Mission College Blvd, Suite 130 Santa Clara, CA 95054 Dear Bryan Shah, Enclosed is the EMC Wireless test report for compliance testing of the Cubic Global Tracking Solutions, Fixed Mesh Gateway, FMG-3 as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-06 ed.), Part 15, Subpart B for a Class A Digital Device and FCC Part 15 Subpart C for Intentional Radiators. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please feel free to contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Warnell Documentation Department Reference: (\Cubic Global Tracking Solutions\EMCS32890-FCC247 Rev. 1) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. Electromagnetic Compatibility Cubic Global Tracking Solutions Cover Page Fixed Mesh Gateway, FMG-3 CFR Title 47, Part 15B, 15.247 MET Report: EMCS32890-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page ii of viii DOC-EMC702 6/18/2009 Electromagnetic Compatibility Criteria Test Report for the Cubic Global Tracking Solutions Fixed Mesh Gateway, FMG-3 Tested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B for Class A Digital Devices & 15.247 Subpart C for Intentional Radiators MET Report: EMCS32890-FCC247 Rev. 1 February 2, 2012 Prepared For: Cubic Global Tracking Solutions 2560 Mission College Blvd, Suite 130 Santa Clara, CA 95054 Prepared By: MET Laboratories, Inc. 3162 Belick St. Santa Clara, CA 95054 Electromagnetic Compatibility Cubic Global Tracking Solutions Cover Page Fixed Mesh Gateway, FMG-3 CFR Title 47, Part 15B, 15.247 MET Report: EMCS32890-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page iii of viii DOC-EMC702 6/18/2009 Electromagnetic Compatibility Criteria Test Report for the Cubic Global Tracking Solutions Fixed Mesh Gateway, FMG-3 Tested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B for Class A Digital Devices & 15.247 Subpart C for Intentional Radiators Anderson Soungpanya, Project Engineer Jennifer Warnell Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of the FCC Rules Parts 15B, 15.247 under normal use and maintenance. Shawn McMillen, Wireless Manager, Electromagnetic Compatibility Lab Electromagnetic Compatibility Cubic Global Tracking Solutions Report Status Fixed Mesh Gateway, FMG-3 CFR Title 47, Part 15B, 15.247 MET Report: EMCS32890-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page iv of viii DOC-EMC702 6/18/2009 Report Status Sheet Revision Report Date Reason for Revision  November 11, 2011 Initial Issue. 1 February 2, 2012 Revised to reflect engineer corrections Electromagnetic Compatibility Cubic Global Tracking Solutions Table of Contents Fixed Mesh Gateway, FMG-3 CFR Title 47, Part 15B, 15.247 MET Report: EMCS32890-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page v of viii DOC-EMC702 6/18/2009 Table of Contents I. Executive Summary .................................................................................................................................................1 A. Purpose of Test ...................................................................................................................................................2 B. Executive Summary ............................................................................................................................................2 II. Equipment Configuration .......................................................................................................................................3 A. Overview .............................................................................................................................................................4 B. References ...........................................................................................................................................................5 C. Test Site ..............................................................................................................................................................5 D. Description of Test Sample .................................................................................................................................6 E. Equipment Configuration ....................................................................................................................................8 F. Support Equipment .............................................................................................................................................8 G. Ports and Cabling Information ............................................................................................................................9 H. Mode of Operation ..............................................................................................................................................9 I. Method of Mo…

Text truncated - open the document above for the full version.

Photograph 1. Conducted Emissions, Test Setup Photograph 2. Radiated Emission, Test Setup Photograph 3. Conducted Emissions, 15.207(a), Test Setup Photograph 4. Radiated Spurious Emissions, Test Setup Photograph 5. Radiated Spurious Emissions, Test Setup, 30 MHz – 1 GHz Photograph 6. Radiated Spurious Emissions, Test Setup, 1 GHz – 18 GHz