Z4C-7000Metal Detector for recreational use

Instruction Manual ii WARNING THIS DOCUMENT CONTAINS INTELLECTUAL PROPERTY, TECHNICAL AND PROPRIETARY DATA AND INFORMATION AND OTHER MATERIAL OWNED SOLELY BY MINELAB ELECTRONICS PTY LIMITED. THIS MATERIAL MUST NOT BE USED WITHOUT THE PRIOR WRITTEN PERMISSION OF MINELAB ELECTRONICS PTY LTD. © MINELAB ELECTRONICS PTY LTD. ALL RIGHTS RESERVED This document is protected by copyright. Apart from any use permitted under the Australian Copyright Act 1968 (Cth) or other applicable laws, any unauthorised use, appropriation or reproduction of this document or any part of it is strictly prohibited. No part of this document may be used or reproduced by any means or by any process, in any form, without the prior written permission of the copyright owner Minelab Electronics Pty Ltd of 118 Hayward Avenue, Torrensville, SA 5031, Australia. ComplIANCe Information to the User (FCC Part 15.105) NOTE: Class B Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help DIsClAImeR The Minelab metal detector discussed in this instruction manual has been expressly designed and manufactured as a quality hobbyist metal detector and is recommended for use in coin, treasure and general metal detection in nonhazardous environments. This metal detector has not been designed for use as a mine detector or as a live munitions detection tool. pleAse Note Since there may be a variety of options available for this detector, equipment may vary according to the Model or items ordered with your detector. Certain descriptions and illustrations may also differ (in this manual) from the exact Model that you purchased. In addition, Minelab reserves the right to respond to ongoing technical progress by introducing changes in design, equipment and technical features at any time. Minelab®, Smartfind™ 2, Wi-Stream™, GPSi™, FindPoint®, GeoHunt™, GeoTrail™, XChange Your Detecting Connection™, Target Trace™ are trademarks of Minelab Electronics Pty. Ltd. Google Maps is a trademark of Google Inc. u-blox is a trademark of u-blox Holding AG. CAUtIoN Before assembling, charging, or using your detector for the first time, please read the important legal and safety information in this manual. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Contents iii Detector Parts 1 Assembly 3 Assembling the Detector 3 Connecting Headphones 5 WM 12 Audio 5 Detector Audio 5 Changing Coils 6 Swing Arm 6 Harness and Extras 6 Charging Batteries 7 BC 10 Battery Charger 7 Battery LED 7 Power LED 7 GPZ 7000 Battery 7 Recharge the Lithium-Ion Battery Pack 8 WM 12 Battery 8 Recharge the WM 12 8 Control Panel 9 GPZ 7000 User Interface 10 Typical Screen Elements 10 Status Bar Elements 10 Summary of Status Bar icons 10 Types of Selection Screens 11 Menu Navigation 12 Navigating the Detector Settings Pages 12 Navigating the Map Pages 12 Map 13 Map 13 GPS 14 Map Elements 14 Zoom Levels 15 Start Trail 15 Current Position 15 FindPoints and WayPoints 15 GeoTrail 15 GeoHunts 15 North Marker 15 Coordinates 16 Navigation Tool 16 Detector Settings Menu 17 Detector Settings Menu Structure 17 Detect Page Overview 17 Detect Plus Page Overview 17 Settings Page Overview 17 Preferences Page Overview 17 User Button Page Overview 17 Reset Page Overview 17 Detect 18 Quick Start 18 Target Type 18 Small Nuggets 18 General 18 Deep Only 18 Ground Type 18 Difficult 18 Normal 18 Noise Cancel 19 Auto Noise Cancel 19 Manual Noise Cancel 19 Sensitivity 19 Adjust Sensitivity Settings 19 Volume 19 Detect Plus 20 Threshold Level 20 Volume Limit 20 Threshold Pitch 21 Ground-Balance Mode 21 Auto 21 Manual 21 Settings 22 GPS 22 Backlight 22 Backlight Brightness 22 Wireless Enable 22 Connect WM 12 22 Connect Additional WM 12 22 Pairing an Additional WM 12 22 Removing Additional WM 12’s 22 Preferences 23 Time Zone 23 Time Format 23 Coordinates Format 23 Length Units 23 Weight Units 23 Wizards 23 User Button 24 Assign a Function to the User Button 24 User Button Functions 24 Backlight 24 View Coordinates 24 View Navigation Tool 24 Threshold Level 24 Ground Balance Mode 24 Other 24 Reset 25 Reset GeoStore 25 Reset Settings 25 Reset All 25 Contents iv Language 25 Change the Language 25 Product Verification Code 25 Version Information 25 Map Menu 26 Map Menu Structure 26 Map Overview 26 GeoStore Page Overview 26 Display Page Overview 26 Create GeoData Page Overview 26 GeoStore 27 Open the GeoStore Menu 27 Map Zoom 27 Sort FindPoints/WayPoints 27 Go to a FindPoint or WayPoint 27 Go to Start/End of a GeoHunt 28 Delete a GeoStore Item 28 Display 29 Open the Display Page 29 Show or Hide Map Screen Elements 29 Recentre 29 Clear Trail 29 View T…

Text truncated - open the document above for the full version.

EMC Technologies Pty Ltd, 176 Harrick VIC 3043 Australia Ph: +613 9365 1000 Fax: +613 9331 7455 www.emctech.com.au EMC Technologies Pty Ltd ABN 82 057 105 549 176 Harrick Road, Keilor Park Victoria Australia 3042 Ph: + 613 9365 1000 Fax: + 613 9331 7455 email: [email protected] To: Federal Communications Commission Attention: Certification Manager No. of pages: 1 From: Donna Lennon Date: 17 th September 2014 EMC Ref: M140534_4 Subject: FCC APPROVAL – FCC ID: Z4C-7000 Please receive EMC Technologies’ Report M140534_4 for review. The EUT is 2.4 GHz Wireless Link, installed in host GPZ7000 Metal Detector. The intention of this application is to FCC certify the 2.4 GHz Wireless Link to FCC 15.249. EMC Technologies Pty Ltd is acting as agent for Minelab Electronics Pty Ltd during this product approval. The FCC ID for this application is Z4C-7000 Regards ______________ Donna Lennon Report Secretary EMC Technologies Pty Ltd

FCC ID: Z4C-7000 ______________________________________________________________________ EMC Technologies Pty. Ltd., 176 Harrick Road, Keilor Park, VIC, 3042, Australia. Phone: +61 3 9365 1000 Fax: +61 3 9331 7455 www.emctech.com.au Appendix A2 – External Photos FCC ID: Z4C-7000 ______________________________________________________________________ EMC Technologies Pty. Ltd., 176 Harrick Road, Keilor Park, VIC, 3042, Australia. Phone: +61 3 9365 1000 Fax: +61 3 9331 7455 www.emctech.com.au Appendix A2 – External Photos FCC ID: Z4C-7000 ______________________________________________________________________ EMC Technologies Pty. Ltd., 176 Harrick Road, Keilor Park, VIC, 3042, Australia. Phone: +61 3 9365 1000 Fax: +61 3 9331 7455 www.emctech.com.au Appendix A2 – External Photos

DECAL CONTROL BOX COMPLIANCE 0.01” (0.25 mm) Matte Lexan 8B35. Adhesive: 3M 467 2 Drawn on Illustrator CS6 118 Hayward Avenue Torrensville SA 5031 Phone: 8238 0888 Fax: 8238 0890 © COPYRIGHT MINELAB 2014 ANGLES DATEAPPCKDDATE DATEDRN DESCRIPTION REF # REV MATERIAL AND FINISH REVISION SCALESHEETSIZEDRAWING NUMBER A4 1:1 1 of 1 DIMENSIONS IN MILLIMETRES UNLESS OTHERWISE STATED 2 DECIMAL (0.00) 1 DECIMALS (0.0) GENERAL TOLERANCES 0 DECIMAL (0) DO NOT SCALE +/- 0.2 +/- 1.0 +/- 0.5 +/- 0.1 Colours: PMS Black PMS White Fonts: Arial Regular Arial Bold Arial Black MINELAB 2705-0069 Notes: 1) All parts and processes to be RoHS compliant. 2) Alternate materials may be used with Minelab Engineering approval. 3) Mininum 2 mm clearance between graphic elements and edge of decal. RELEASE FOR PRODUCTION D.00057 1 SMQ 18-06-14 EDP 19-06-14 CL 23-06-14 REPLACE C-TICK WITH REGULATORY COMPLIANCE MARK (RCM)D.000572SMQ29-07-14EDPCL29-07-1429-07-14 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: Z4C-7000 64.0 R 1.0 Typ 3.0 29.3

GPZ 7000 Internal Module Photographs Figure 1. GPS Module Figure 1a. GPS Receiver with can removed Figure2. GPS antenna with shield removed Figure 3. User Interface Pod with screen moved aside and shield removed Figure 2. WM12 module, showing PCB antenna (bottom) Figure 3. WM12 module, top-side

Page 1 of 19 TEST REPORT FOR CERTIFICATION to FCC PART 15 Subpart C (Section 15.249) FCC ID: Z4C-7000 Test Sample: Metal Detector Model: Jupiter Report Number: M140534-4 Tested for: Minelab Electronics Pty Ltd Issue Date: 22 nd September 2014 EMC Technologies Pty Ltd reports apply only to the specific samples tested under stated test conditions. It is the manufacturer’s responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. EMC Technologies Pty Ltd shall have no liability for any deductions, inferences or generalisations drawn by the client or others from EMC Technologies Pty Ltd issued reports. This report shall not be used to claim, constitute or imply product endorsement by EMC Technologies Pty Ltd. This document is issued in accordance with NATA’s accreditation requirements. The results of tests, calibration and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document shall not be reproduced except in full. EMC Technologies Pty Ltd ABN 82 057 105 549 176 Harrick Road Keilor Park Victoria Australia 3042 Ph: + 61 (0)3 9365 1000 Fax: + 61 (0)3 9331 7455 Email: [email protected] FCC ID: Z4C-7000 Report No. M140534-4 Page 2 of 19 This document is issued in accordance with NATA’s accreditation requirements. The results of tests, calibration and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document shall not be reproduced except in full. TEST REPORT FOR CERTIFICATION to FCC PART 15 Subpart C (Section 15.249) EMC Technologies Report No. M140453-4 Issue Date: 22 nd September 2014 CONTENTS 1.0 INTRODUCTION 2.0 GENERAL INFORMATION 3.0 TEST RESULTS 3.1 §15.203 Antenna Requirement 3.2 §15.207 Conducted Limits 3.3 §15.209 Radiated Emission Limits; General Requirements 3.4 §15.249(a) Fundamental and Harmonic Emissions 3.5 §15.249(b) Fixed, Point to Point 3.6 §15.249(c) Field strength limits at 3 metres 3.7 §15.249(d and e) Spurious Emissions 4.0 COMPLIANCE STATEMENT 5.0 MEASUREMENT UNCERTAINTY APPENDIX A: PHOTOGRAPHS APPENDIX B: BLOCK DIAGRAM APPENDIX C: SCHEMATICS APPENDIX D: OPERATIONAL DESCRIPTION APPENDIX E: FCC LABEL DETAILS APPENDIX F: USER MANUAL APPENDIX G: ANTENNA OPERATIONAL DESCRIPTION FCC ID: Z4C-7000 Report No. M140534-4 Page 3 of 19 This document is issued in accordance with NATA’s accreditation requirements. The results of tests, calibration and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document shall not be reproduced except in full. TEST REPORT FOR CERTIFICATION to FCC PART 15 Subpart C (Section 15.249) Report Number: M140534-4 Sample: Metal Detector Model: Jupiter FCC ID: Z4C-7000 Equipment Type: Intentional Radiator (Transceiver) Manufacturer: Minelab Electronics Pty Ltd Address: 118 Hayward Avenue, Torrensville SA 5031, AUSTRALIA Contact: Mark Lawrie Tested for: Minelab Electronics Pty Ltd Standards: FCC Part 15 – Radio Frequency Devices FCC Part 15 Subpart C – Intentional Radiators Section 15.247: 2400 – 2483.5 MHz Operation Bands ANSI C63.4 – 2009 American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Test Dates: 19 th June to 25 th June 2014 Test Engineer: Kevin Hansen Attestation: I hereby certify that the device(s) described herein were tested as described in this report and that the data included is that which was obtained during such testing. Authorised Signatory: Chris Zombolas Technical Director EMC Technologies Pty Ltd FCC ID: Z4C-7000 Report No. M140534-4 Page 4 of 19 This document is issued in accordance with NATA’s accreditation requirements. The results of tests, calibration and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document shall not be reproduced except in full. TEST REPORT FOR CERTIFICATION to FCC PART 15 Subpart C (Section 15.249) 1.0 INTRODUCTION Test results and procedures were performed in accordance with the following Federal Communications Commission (FCC) standards/regulations: 47 CFR, Part 15, Subpart C: Rules for intentional radiators (particularly section 15.247) Section 15.203: Antenna requirements Section 15.209: Radiated Emission Limits (General requirements) Section 15.249: Operation in the bands 902-928 MHz, 2400-2483.5 MHz, 5725-5850 MHz The sample complied with the requirements of 47 CFR, Part 15 Subpart C - Section 15.249. The measurement procedure used was in accordance with ANSI C63.4-2009. The instrumentation conformed to the requirements of ANSI C63.2-1996. 1.1 Summary of Results FCC Part 15 Subpart C Test Performed Results 15.203 Antenna Requirement Not Applicable 15.207 Conducted Emissions Not Applicable 15.209 Radiated Emissions Complied 15.249 (a) Fundamental Field Strength Complied 15.249 (a) Harmonics Emissions Complied 15.249 (b) Fixed, point to point Not Applicable 15.249 (c) Field strength limits @ 3 meters Noted 15.249 (d) Spurious Emissions Complied 15.249 (e) 20 dB Peak to Average Complied 1.2 Modifications by EMC Technologies No modifications were performed. FCC ID: Z4C-7000 Report No. M140534-4 Page 5 of 19 This document is issued in accordance with NATA’s accreditation requirements. The results of tests, calibration and/or measurements included in this docume…

Text truncated - open the document above for the full version.

FCC ID: Z4C-7000 ______________________________________________________________________ EMC Technologies Pty. Ltd., 176 Harrick Road, Keilor Park, VIC, 3042, Australia. Phone: +61 3 9365 1000 Fax: +61 3 9331 7455 www.emctech.com.au Appendix A3 – Test Setup Photos FCC ID: Z4C-7000 ______________________________________________________________________ EMC Technologies Pty. Ltd., 176 Harrick Road, Keilor Park, VIC, 3042, Australia. Phone: +61 3 9365 1000 Fax: +61 3 9331 7455 www.emctech.com.au