ZBCWD254AWIRELESS CHARGER

Watch Magnetic Charger user manual Model：WD-254A Contents 1.What is in the box 2.Product Introduction 3.Specification 4.How to use 5.Important Notification Thanks for purchasing this fantastic Watch Magnetic Charger Please read the manual in detail for proper operation before you get to start to use. What is in the box: 1)Watch Magnetic Charger x1pc 2) User Manual x1pc Manufacturer: SHENZHEN DNS INDUSTRIES CO., LTD. Address:23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, Shenzhen, China The importer: XXXXXXXXXXXX The importer: XXXXXXXXXXXXXXX Input: DC 5V 1A Output: 2.5W(Max) Operating Frequency Range: 326.5KHz FCC ID: ZBCWD254A Scope of application: Scopt of application Smart matches apple's offical iWatch model; Small and light, easy and portable; No precise alignment is required, just keep the joint close to the back of the watch, where the magnet can adsorb the joint into place. NOTE: This equipment has been tested and found to comply with the limits for a wireless power charger, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Warning Statement： This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.

SHENZHEN DNS INDUSTRIES CO., LTD. Date: 2021-05-20 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: ZBCWD254A To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with SHENZHEN DNS INDUSTRIES CO., LTD. This authorization is valid until further written notice from the applicant. Print Name: Ms Yuki Wu Title: Certification Engineer Signature: On behalf of Company: SHENZHEN DNS INDUSTRIES CO., LTD. Telephone: +86-755-83401338 E-mail: [email protected]

SHENZHEN DNS INDUSTRIES CO., LTD. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: ZBCWD254A LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Ms Yuki Wu Title: Certification Engineer Signature: On behalf of Company: SHENZHEN DNS INDUSTRIES CO., LTD. Telephone: +86-755-83401338 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name SHENZHEN DNS INDUSTRIES CO., LTD. Address 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian,shenzhen 518026,China Grantee Code ZBC FCC ID ZBCWD254A Authorized Contact Name Yuki Wu Contact Email [email protected] Contact Phone +86-755-83401338 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: Print Name: Yuki Wu Title: Certification Engineer *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

SHENZHEN DNS INDUSTRIES CO., LTD Cover Letter-Wireless Charger Approval Date: 2021-04-26 Gentlemen: There’s a Watch Magnetic Charger that would like to have your authorization as an Inductive wireless power transfer applications approval. The specific product as below, Watch Magnetic Charger, with its designed features and specified description, meets special requirements for KDB 680106 D01 section 5.2 requirements. Company: SHENZHEN DNS INDUSTRIES CO., LTD. Product Name: Watch Magnetic Charger Model Number: WD-254A, WD-254B, 699396 FCC ID: ZBCWD254A KDB 680106 D01 Section 5.2 Requirements Product Technical Specification Result a) Power transfer frequency is less that 1 MHz 326.5kHz Complied b) Output power from each primary coil is less than or equal to 15 watts. 2.5 watts Complied c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils Complied d) Client device is placed directly in contact with the transmitter. Complied e) Mobile exposure conditions only For inductive applications where the primary does not physically attach to the client, and it is intended for desktop use, the desktop guidance in KDB 680106 D01 may be applied Complied f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Please refer to RF exposure report Complied Sincerely, Print Name: Ms Yuki Wu Title: Certification Engineer Signature: On behalf of Company: SHENZHEN DNS INDUSTRIES CO., LTD. Telephone: +86-755-83401338 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 External Photos for SZCR2104020531AT FCC ID: ZBCWD254A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 1 Photographs Test model No.: WD-254A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 Test model No.: WD-254B SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 7

2021.03.31 WD540006H013 iWatch Wireless Charger CM000930 699396 Size: 17.5 x 16.9 mm MID#DN0012106CN: MID# DN001 DNS(DN002DNS 2106 CNPH WD-254A Output: 2.5W(max) FCC ID: ZBCWD254A Made in China Input: 5V 1A Watch Magnetic Charger

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 Internal Photos for SZCR2104020531AT FCC ID: ZBCWD254A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 1 EUT Constructional Details Test model No.: WD-254B SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 7 Test model No.: WD-254A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 7

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 1 of 9 Keny Xu EMC Laboratory Manager 1 COVER PAGE Human Exposure Report Application No.: SZCR2104020531AT Applicant: SHENZHEN DNS INDUSTRIES CO., LTD. Address of Applicant: 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, shenzhen, 518026 China Manufacturer: SHENZHEN DNS INDUSTRIES CO., LTD. Address of Manufacturer: 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, Shenzhen, China Factory: 1. HUIZHOU D&S CABLE CO., LTD. 2. HUI ZHOU DNS TECHNOLOGY CO., LTD. 3. D AND S INDUSTRIES (PHILIPPINES) CORPORATION Address of Factory: 1. Longjin Dongjiang Industry Zone Shuikou, Huicheng, Huizhou, Guangdong, China 2. 5 Dongshun South Road, Dongjiang Hi-tech Industrial Park,Zhongkai Hi- tech Zone, Huizhou City, Guangdong, China 3. 1 to 5 Orient Goldcrest Suntrust Ecotown Building 2, Lot 8 Block 8, Sahud Ulan, Suntrust Ecotown Tanza, Region IV-A, Cavite, Philippines Equipment Under Test (EUT): EUT Name: WIRELESS CHARGER, iWatch portable charger with USB A cable iWatch portable charger with USB C cable Model No.: WD-254A, WD-254B, 699396 ♣ ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: DNS, omars, mbest, NOVOO, KEYMOX, Infinitive FCC ID: ZBCWD254A Standards: 47 CFR PART 1, Subpart I, Section 1.1310 47 CFR PART 2, Subpart J, Section 2.1091 Date of Receipt: 2021-04-14 Date of Test: 2021-04-17 to 2021-04-26 Date of Issue: 2021-04-26 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 2 of 9 Revision Record Version Chapter Date Modifier Remark 01 2021-04-26 Original Authorized for issue by: Leo Li/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 3 of 9 2 Contents 1 COVER PAGE 1 2 CONTENTS 3 3 GENERAL INFORMATION 4 3.1 DETAILS OF E.U.T. 4 3.2 DESCRIPTION OF SUPPORT UNITS 5 3.3 TEST LOCATION 6 3.4 TEST FACILITY 6 3.5 DEVIATION FROM STANDARDS 6 3.6 ABNORMALITIES FROM STANDARD CONDITIONS 6 4 EQUIPMENTS USED DURING TEST 7 5 TEST RESULTS 8 5.1 RF EXPOSURE TEST 8 5.1.1 E.U.T. Operation 8 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 4 of 9 3 General Information 3.1 Details of E.U.T. Power adapter: Input: DC 5V, 1A Output: DC 5V, 0.5A(2.5W) Power supply: Input: DC 5V, 1A Output: 2.5W(Max) Operation frequency: 326.5kHz Modulation type: Load modulation Antenna type: Loop Antenna Declaration of EUT Family Grouping: Model No.: WD-254A, WD-254B, 699396 Only the model WD-254B was tested. According to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on input port, circuitry about power input, product name, and trade mark. Details see below: Trade mark Product name Model number input port circuitry about power input DNS,omars,mbest,NOVOO, KEYMOX Wireless Charger for Apple Watch, Watch Magnetic Charger WD-254A USB A See note DNS,omars,mbest,NOVOO, KEYMOX Wireless Charger for Apple Watch, Watch Magnetic Charger WD-254B TYPE C See note Infinitive Wireless Charger for Apple Watch, Watch Magnetic Charger 699396 USB A See note SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 5 of 9 Note : circuitry about USB A port circuitry about TYPE C port 3.2 Description of Support Units Description Manufacturer Model No. Serial No. iwatch Apple Series5 N/A Adapter Apple A1357 REF. No.SEA0501C SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 6 of 9 3.3 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch E&E Lab, No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong,China 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0006. IC#: 4620C. 3.5 Deviation from Standards None. 3.6 Abnormalities from Standard Conditions None. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 7 of 9 4 Equipments Used during Test Item Test Equipment Manufacturer Model No. Inventory No.Cal. Due date 1 Electric and Magnetic Field Analyzer Narda EHP-50F EMC092 2021-11-26 2 3m Fully-Anechoic Chamber AUDIX N/A SEM001-02 2022-03-22 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053102 Page: 8 of 9 5 Test Results 5.1 RF Ex…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053101 Page: 1 of 36 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2104020531AT Applicant: SHENZHEN DNS INDUSTRIES CO., LTD. Address of Applicant: 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, shenzhen, 518026 China Manufacturer: SHENZHEN DNS INDUSTRIES CO., LTD. Address of Manufacturer: 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, Shenzhen, China Factory: 1. HUIZHOU D&S CABLE CO., LTD. 2. HUI ZHOU DNS TECHNOLOGY CO., LTD. 3. D AND S INDUSTRIES (PHILIPPINES) CORPORATION Address of Factory: 1. Longjin Dongjiang Industry Zone Shuikou, Huicheng, Huizhou, Guangdong, China 2. 5 Dongshun South Road, Dongjiang Hi-tech Industrial Park,Zhongkai Hi- tech Zone, Huizhou City, Guangdong, China 3. 1 to 5 Orient Goldcrest Suntrust Ecotown Building 2, Lot 8 Block 8, Sahud Ulan, Suntrust Ecotown Tanza, Region IV-A, Cavite, Philippines Equipment Under Test (EUT): EUT Name: WIRELESS CHARGER, iWatch portable charger with USB A cable iWatch portable charger with USB C cable Model No.: WD-254A, WD-254B, 699396 ♣ ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: DNS, omars, mbest, NOVOO, KEYMOX, Infinitive FCC ID: ZBCWD254A Standard(s) : 47 CFR Part 15, Subpart C Date of Receipt: 2021-04-14 Date of Test: 2021-04-17 to 2021-04-26 Date of Issue: 2021-04-26 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053101 Page: 2 of 36 Revision Record Version Chapter Date Modifier Remark 01 2021-04-26 Original Authorized for issue by: Leo Li/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053101 Page: 3 of 36 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Mains Power Port (150kHz-30MHz) 47 CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Radiated Emissions (30MHz-1GHz) ANSI C63.10 (2013) Section 6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Emissions (9kHz-30MHz) ANSI C63.10 (2013) Section 6.4 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass 20dB Bandwidth ANSI C63.10 (2013) Section 6.9.2 47 CFR Part 15, Subpart C 15.215 Pass Restricted Bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 Pass Declaration of EUT Family Grouping: Model No.: WD-254A, WD-254B, 699396 Only the model WD-254B was tested fully, and the model WD-254A was performed the Radiated Emissions (30MHz-1GHz), Radiated Emissions (9kHz-30MHz) and Conducted Emissions at AC Mains Power Port (150kHz-30MHz) tests for discrepancy According to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on input port, circuitry about power input, product name, and trade mark. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053101 Page: 4 of 36 Details see below: Trade mark Product name Model number input port circuitry about power input DNS,omars,mbest ,NOVOO, KEYMOX Wireless Charger for Apple Watch, Watch Magnetic Charger WD-254A USB A See note DNS,omars,mbest ,NOVOO, KEYMOX Wireless Charger for Apple Watch, Watch Magnetic Charger WD-254B TYPE C See note Infinitive Wireless Charger for Apple Watch, Watch Magnetic Charger 699396 USB A See note Note : circuitry about USB A port circuitry about TYPE C port SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210402053101 Page: 5 of 36 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 5 4 GENERAL INFORMATION .................................................................................................................. 7 4.1 DETAILS OF E.U.T. ......................................................................................................................... 7 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 7 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 7 4.4 TEST LOCATION ............................................................................................................................. 8 4.5 TEST FACILITY ............................................................................................................................... 8 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 8 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 8 5 EQUIPMENT LIST ............................................................................................................................... 9 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................11 6.1 ANTENNA REQUIREMENT ...............................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 RF Exposure Setup Photos for SZCR2104020531AT FCC ID: ZBCWD254A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 1 Photographs SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZCR2104020531AT FCC ID: ZBCWD254A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs Conducted Emissions at AC Mains Power Port (150kHz-30MHz) Radiated Emissions (30MHz-1GHz) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 Radiated Emissions (9kHz-30MHz)