ZDIK2-36411N Wireless USB Module

Shenzhen Kingnet Electronic Co., Ltd 11N Wire less USB Module K2-364 User Manual K2-364 IEEE 802.11b/g/n Mini 6PIN USB 2.0 wireless module Datasheet Version 1.2 Document release Date Modification Approved Version 1.0 2010/12/27 Initial release Lu Hong Version 1.1 2011/1/4 Add consume information Lu Hong Version 1.2 2011-1-14 Add ANTENNA option Chen Yong 1. Introduction Our IEEE 802.11b/g/n Mini 6PIN USB 2.0 wireless module ---K2-364 USB 2.0 wireless module is a highly integrated wireless local area network (WLAN) solution to let users enjoy the digital content through the latest wireless technology without using the extra cables and cords. it enables a high performance cost effective low power. Compliant with the IEEE 802.11b/g/n standard, the K2-364 uses Direct sequence Spread Spectrum(DSSS),Orthogonal Frequency Division Multiplexing(OFDM), BPSK, QPSK, CCK and QAM baseband modulation technologies, A high level of integration and full implementation of the power management functions specified in the IEEE802.11 standard minimize system power requirement by using K2-364. 2. Feature Wireless N speed up to 150M bps , 1T1R delivers greater throughput at range versus conventional 1T1R Lowe Power consumption and high performance Supports 64/128 WEP, WPA /WPA2/WPA-PSK/WPA2-PSK(TKIP/AES), supports IEEE 802.1X Supports Windows 2000, Windows XP 32/64bit, Vista 32/64bit, Windows 7 32/64bit，Linux Supports ad-hoc and infrastructure mode Seamlessly compatible with 802.11n/b/g products 3. General Specification Hardware Features Model K2-364 INTERFACE Mini 6PIN USB2.0 module ANTENNA TYPE On-board (option1) IPEX connect(option2) Chipset solution AR9271 Voltage 3.3V DIMENTIONS(W×D×H) 40*17*3mm Wireless Features WIRELESS STANDARDS IEEE 802.11n, IEEE 802.11g, IEEE 802.11b FREQUENCY RANGE 2.400-2.4835GHz SIGNAL RATE 11n: Up to 150Mbps(dynamic) 11g: Up to 54Mbps(dynamic) 11b: Up to 11Mbps(dynamic) RECEIVE SENSITIVITY 130M: -68dBm@10% PER 108M: -68dBm@10% PER 54M: -68dBm@10% PER 11M: -85dBm@8% PER 6M: -88dBm@10% PER 1M: -90dBm@8% PER MODULATION TECHNOLOGY DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM WIRELESS SECURITY Support 64/128 bit WEP, WPA-PSK/WPA2-PSK, Wireless MAC Filtering WIRELESS TRANSMIT POWER <15dBm(EIRP) WORK MODE Ad-Hoc / Infrastructure mode Others CERTIFICATION CE, FCC, RoHS CONSUME 500mW(Typical) PACKAGE CONTENTS Bulk packing: Wireless Adapter K2-364 100PCS/CTN SYSTEM REQUIREMENTS Windows 7(32/64bits), Windows Vista(32/64bits), Windows XP(32/64bits), Windows 2000,Linux ENVIRONMENT Operating Temperature: 0°C~40°C (32°F~104°F) Storage Temperature: -40°C~70°C (-40°F~158°F) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing 4. PCB print 5. Pin definition Pin number Name Type Description 1 Radio on/off I/O Disable WLAN RF when low, floating is not allowed 2 Power Power 3.3V Power input 3 USB_D- Digital USB Differential signal 4 USB_D+ Digital USB Differential signal 5 GND Power Ground 6 LED Output Active low signal. The signal is used to provide status indicators via LED 6. Mechanical Dimension ( Size: mm) Caution: Use 11N Wireless USB Module in the environment with the temperature between-20°C and 50°C; otherwise, it may damage your phone.It can be operating under 2000m。 For the following equipment: 11N Wireless USB Module Is in compliance with the essential requirements and other relevant Provisions of Directive 1999/5/EC. The equipment was passed. The test was performed according to the following European standards: EN 301 489-1 V1.8.1 :2008 EN 60950-1:2006+A11:2009 EN 300 328 V1.7.1:2006 EN 301 489-17V1.3.2: 2009 EN 62311:2008 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC ID: ZDIK2-364 WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipments. In order to comply with RF exposure requirements, a minimum distance of 20 cm must be maintained between the antenna and all persons

Mar. 31, 2011 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Colombia, Maryland 21046 Subject: The Module is not able to exchange data with a PC and responsible for the test report FCC ID: ZDIK2-364 Gentlemen; The module (FCC ID: ZDIK2-364) is not a USB device, and it's also not able to connect to the USB port directly. Our company shall take any responsibility for the Test report for which it didn’t show the radiated emissions although the radiated emissions measurement of the band edge has already been performed surely. Shenzhen Kingnet Technology Co.,Ltd Commy Lu/ Sales Manager

Mar.17, 2011 Federal Communication Commission Authorization and Evaluation Division FCC ID: ZDIK2-364 Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1: Block Diagram 2: Circuit Diagram 3: Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Shenzhen Kingnet Technology Co.,Ltd Contact person: Commy Title: Sales Manager Tel: 86-755-26982337

Shenzhen Kingnet Technology Co.,Ltd Tel: 593-4-2646663 3F,Building 5,Civil Science Industry Zone, Pingshan,Xili,Nanshan,Shenzhen China Fax: 593-4-2646663 Date: Mar. 17, 2011 FCC IDZDIK2-364 Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Attestation of Global Compliance Co., Ltd. Address:1F., No.2 Building, Huafeng No.1 Technical Industrial Park, Sanwei, Xixiang, Baoan District, Shenzhen Name: Yimi ZHAO Job Title: EMC Manager Email: [email protected] I am therefore responsible for the contents of the application. Model Name of the specified radio equipment: FCC ID: ZDIK2-364 Product Name: 11N Wireless USB Module Signature________ __________ FCC grantee contact person information. Name/Title: Commy Lu/ Sales Manager Company Name: Shenzhen Kingnet Technoloty Co.,Ltd Address: 3F,Building 5,Civil Science Industry Zone,Pingshan,Xili,Nanshan, Shenzhen China TEL: 86-755-26982337 FAX: 86-755-26515635

Mar.25, 2011 Request for Modular Approval Attestation for the 2.4 GHz Module (FCC ID: ZDIK2-364) Per the FCC Public Notice DA-00-1407 for Part 15 Unlicensed Modular Transmitter approval the following information is provided: 1) PN DA 00-1407 Page 2 Item 1: The EUT must have its own RF Shielding and be a complete RF transmitter. The EUT must not rely upon the shielding provided by the device into which it is installed for RF shielding. The EUT has its own RF Shielding and be a complete RF transmitter, please see the EUT internal photos. And the EUT doesn’t rely upon the shielding provided by the device into which it’s installed for RF shielding. 2) PN DA 00-1407 Page 2 Item 2: The EUT must have buffered modulation/data inputs. The Module has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over-modulation. 3) PN DA 00-1407 Page 2 Item 3: The EUT must have its own power supply regulation and VCO built-in. The module contains an onboard supply voltage regulator 4) PN DA 00-1407 Page 2 Item 4: The antenna must either be permanently attached or employ a “unique” antenna connector. Any antenna used with module must be approved with the module at time of initial authorization. Professional installation provision may not be applied to modules regarding use of any other antenna other then the one authorized at the time of Certification of the module. The transmitter shall only be used with the tested integral antenna 5) PN DA 00-1407 Page 2 Item 4: Any antenna used with the module must be approved with the module. (The “professional installation” provision (15.203) may not be applied to modules) The transmitter shall only be used with the tested integral antenna 6) PN DA 00-1407 Page 2 Item: The modular transmitter must be tested in a stand-alone configuration. i.e., the module must not be inside another device during testing. (If tested in a Host Device then there must be a specific note on the Certification.) The module was tested in a stand-alone configuration. 7) PN DA 00-1407 Page 2 Item: Unless the module is battery powered, it must comply with the AC line conducted requirements found in Section 15.207. The module was tested to comply with the section 15.207 8) PN DA 00-1407 Page 2 Item: AC, DC, and data input/output lines must not contain ferrites, unless they will be marketed with the module. The AC, DC, and data input/output lines doesn’t contain ferrites. 9) PN DA 00-1407 Page 2 Item: The module must have its own FCC ID and if not visible when installed inside another device, the outside device must display a label referring to the enclosed module. In this case, a copy of the instructions must be included in the application for equipment authorization. The module have its own FCC ID Label. 10) PN DA 00-1407 Page 2 Item: The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and must provide ADEQUATE instructions along with the module to explain any such requirements. The module is compliance with all applicable FCC rules. Detail instructions are given in the user’s manual. 11) PN DA 00-1407 Page 2 Item: The module must comply with RF exposure requirements. See FCC Rules. Spread Spectrum transmitters must comply with RF exposure limits in 15.247. The module complies to FCC Part 15.247 and has a measured maximum measured power output of 14.91 dBm EIRP. The module is compliance with all applicable FCC RF exposure requirements. 12) PN DA 00-1407 Page 2 Item: When approved, the grant of equipment authorization for the transmitter module MUST have the word “module” or “modular” added to the Remarks section of the grant. Add the word “module” to the grant Sincerely, Shenzhen Kingnet Technology Co.,Ltd Commy/Sales Manager

External Photos

FCC ID LABEL

LABEL PLACEMENT

External Photos

FCC Test Report Report No.: AGC00M110101‐1F2B FCC ID : ZDIK2‐364 PRODUCT DESIGNATION : 11N Wireless USB Module BRAND NAME : KINGNET TEST MODEL : K2‐364 CLIENT : Shenzhen Kingnet Technology Co.,Ltd DATE OF ISSUE : February 23, 2011 STANDARD(S) : FCC Part 15 Rules Attestation of Global Compliance Co., Ltd. CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC00M110101-1F2B Page 1 of 38 VERIFICATION OF COMPLIANCE Applicant Shenzhen Kingnet Technology Co.,Ltd 3F,Building 5,Civil Science Industry Zone,Pingshan,Xili,Nanshan,Shenzhen China Manufacturer Shenzhen Kingnet Electronic Co.,Ltd 1-4F,Building 5Civil Science Industry Zone,Pingshan,Xili,Nanshan,Shenzhen China Product Designation 11N Wireless USB Module Brand Name KINGNET Model Name K2-364 FCC ID ZDIK2-364 Report Number AGC00M110101-1F2B Date of Test February 18-February 23, 2011 WE HEREBY CERTIFY THAT: The above equipment was tested by Attestation of Global Compliance Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003) and the energy emitted by the sample EUT tested as described in this report is in compliance with radiated emission limits of FCC Rules Part 15.247. Checked By: Forrest Lei Feb.23, 2011 Authorized By King Zhang Feb.23, 2011 Report No.: AGC00M110101-1F2B Page 2 of 38 TABLE OF CONTENTS 1. GENERAL INFORMATION ........................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION ...................................................................................................................................... 4 1.2 TABLE OF CARRIER FREQUENCYS ................................................................................................................... 4 1.3 IEEE 802.11N MODULATION SCHEME .............................................................................................................. 5 1.4 RELATED SUBMITTAL(S) / GRANT (S) .............................................................................................................. 5 1.5 TEST METHODOLOGY ........................................................................................................................................... 5 1.6 TEST FACILITY ......................................................................................................................................................... 5 1.7 SPECIAL ACCESSORIES ....................................................................................................................................... 5 1.8 EQUIPMENT MODIFICATIONS ............................................................................................................................. 5 1.9 TABLE FOR TEST MODES ..................................................................................................................................... 6 2. SYSTEM TEST CONFIGURATION ............................................................................................................................. 7 2.1 CONFIGURATION OF TESTED SYSTEM ........................................................................................................... 7 2.2 EQUIPMENT USED IN TESTED SYSTEM .......................................................................................................... 7 3. SUMMARY OF TEST RESULTS ................................................................................................................................. 8 4. DESCRIPTION OF TEST MODES .............................................................................................................................. 8 5MAXIMUM OUTPUT POWER ........................................................................................................................................ 9 5.1 MEASUREMENT PROCEDURE ............................................................................................................................ 9 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................................. 9 5.3 MEASUREMENT EQUIPMENT USED ................................................................................................................. 9 5.4 LIMITS AND MEASUREMENT RESULT ............................................................................................................ 10 6 6 DB BANDWIDTH ....................................................................................................................................................... 11 6.1 MEASUREMENT PROCEDURE .......................................................................................................................... 11 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ........................................................................... 11 6.3 MEASUREMENT EQUIPMENT USED ............................................................................................................... 11 6.4 LIMITS AND MEASUREMENT RESULTS ......................................................................................................... 11 7. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ................................................................. 15 7.1 MEASUREMENT PROCEDURE .......................................................................................................................... 15 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ........................................................................... 15 7.3 MEASUREMENT EQUIPMENT USED ............................................................................................................... 15 7.4 LIMITS AND MEASUREMENT RESULT ...........................................................................…

Text truncated - open the document above for the full version.

RADIATED EMISSION TEST SETUP CONDUCTED EMISSION TEST SETUP