ZEH04142110 Tag Module

PLUS Limited Module Tag Model 2110 User Manual Manual Model 2110 Limited Module Tag Manual Page 2 of 12 Contents Regulatory & Legal Information .............................................................................................................................. 3 Safety Information .................................................................................................................................................. 4 Revisions to this Document .................................................................................................................................... 5 Introduction ............................................................................................................................................................ 6 Overview ................................................................................................................................................................. 7 Specifications .......................................................................................................................................................... 9 Mounting ............................................................................................................................................................... 10 Identification ......................................................................................................................................................... 10 FCC Section 15.212 Compliance ........................................................................................................................... 11 End Product ID Recommended Format ................................................................................................................ 12 Model 2110 Limited Module Tag Manual Page 3 of 12 Regulatory and Legal Information Copyright © PLUS ® Location Systems. No part of this manual may be copied or reproduced without prior written consent from PLUS ® Location Systems. Disclaimer The information in this document is subject to change without notice. PLUS ® Location Services (“PLUS”) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, contact your local supplier or visit us online at www.pluslocation.com. Trademarks & Patents PLUS and the PLUS logo are trademarks of PLUS ® Location Systems. Other trademarks and trade names used in this manual are the property of the manufacturers or vendors of the respective products. Intended Use This document examines the PLUS 2110 Modular Tag. This document is intended for PLUS Location Systems internal use only. FCC Compliance U.S. Operation: This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (3) Operation on board an aircraft or a satellite is prohibited. (4) Devices operating under this section may not be employed for the operation of toys. (5) Except for operation onboard a ship or a terrestrial transportation vehicle, the use of a fixed outdoor infrastructure is prohibited. A fixed infrastructure includes antennas mounted on outdoor structures, e.g., antennas mounted on the outside of a building or on a telephone pole. This outdoor infrastructure prohibition applies to intentional ultra-wideband (UWB) emitters. Operation in disregard of these conditions is a violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. Disassembling or modifying the unit will void both FCC compliance and PLUS ® Location Systems warranty provisions. Manufacturer Contact Information PLUS Location Systems USA, LLC 6767 Old Madison Pike NW, Suite 310 Huntsville, AL 35806 www.pluslocation.com Model 2110 Limited Module Tag Manual Page 4 of 12 Safety Information Read and follow all instructions before using the Model 2110 Tag when it has been incorporated into a host product. The following are typical safety instructions for a PLUS Tag that would apply to a host product using the 2110 Module.  Do not use the Tag if it has been damaged.  Do not install in environments that exceed temperature and humidity requirements.  Do not leave the Tag on a heat source.  Never open the case on the Tag: There are no user serviceable parts or replaceable parts inside the enclosure. Model 2110 Limited Module Tag Manual Page 5 of 12 Revisions to this Document Version Comments Release Date Rev A Initial release 05/29/2014 Rev B Updates in response to FCC request for clarification 8/18/2014 Model 2110 Limited Module Tag Manual Page 6 of 12 Introduction The Plus Model 2110 Limited Module is a modular design for integration into a host product consisting of, at a minimum, an enclosure and a 3 VDC battery. It has the following features:  Runs from a 3 VDC power source (can operate down to 2 volts DC)  Will transmit a UWB packet at a rate set at time of manufacture. Rate can be set to 1Hz, 6Hz, or 10Hz.  Meets FCC Section 15.212, rules concerning single limited modular transmitters.  Certified to comply with FCC Part 15.519 Model 2110 Limited Module Tag Manual Page 7 of 12 Overview Background Tag tracking is accomplished by analyzing time-differences-of-arrival (TDOAs) of tag transmissions. When a tag transmits a packet, PLUS ® Sensors that successfully receive the packet will send out information concerning the tag packet, including a precise timestamp. The difference in the timestamp between sensors gives the TDOA for that sensor pair/tag combination. At least three sensors must hear a tag in order to determine a valid position for that tag. Model 2110 Limited Modular Tag The 2110 Limited Modular Tag allows the imp…

Text truncated - open the document above for the full version.

Cummings Research Park 6767 Old Madison Pike, Suite 310 Huntsville AL 35806 P: +1 256-217-4072 M:+1 256-964-7614 www.pluslocation.com May 20, 2014 Request for Confidential Treatment FCC ID ZEH0414 PLUS Location Systems (PLUS) requests that all schematics be withheld from public disclosure in accordance with Section 0.457 and 0.459 of the Commission’s Rules, 47 C.F.R., following grant of the application. In support of this request, PLUS submits the following: (1) identification of the specific information for which confidential treatment is sought: PLUS Location Systems seeks confidentiality for all schematics of the device. These exhibits are segregated from the non-confidential exhibits of the application. (2) identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission: The proceeding is that involving the application for equipment authorization (certification) under FCC ID ZEH0414. (3) explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged: This material includes circuit diagrams and board layout information for the system. As such, this material is treated as highly confidential business information. (4) explanation of the degree to which the information concerns a service that is subject to competition: The material for which confidentiality is sought is employed in the design and manufacture of ultra-wideband tracking systems that are offered on a highly competitive basis. Customers for this equipment have a variety of competing sources of supply. (5) explanation of how disclosure of the information could result in substantial competitive harm: Disclosure would, in effect, give away the fruits of the labors of the engineering department, who have designed the equipment and the manufacturing processes. Disclosure would also offer competitors additional unwarranted insight into the state of product development Cummings Research Park 6767 Old Madison Pike, Suite 310 Huntsville AL 35806 P: +1 256-217-4072 M:+1 256-964-7614 www.pluslocation.com thereby allowing such competitors an advantage that would not be available to them unless they were working with PLUS and had a non-disclosure agreement with PLUS. (6) identification of any measures taken by the submitting party to prevent unauthorized disclosure: The information for which confidential treatment is sought is kept confidential by PLUS and not made available to third parties except pursuant to non-disclosure agreements. (7) identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties: To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. The protection sought is narrowly drawn and pertains to certain specific implementations of ultra-wideband technology. (8) justification of the period during which the submitting party asserts that material should not be available for public disclosure: This material should not be disclosed for at least five years. Disclosure of the design information would lead to insights into both designs and manufacturing techniques and could have an adverse competitive effect for many years to come. (PLUS is aware, for example, of overseas competitors for this application.) As this is industrial equipment, we expect the equipment to be used for more than five years in some cases. (9) any other information that the party seeking confidential treatment believes may be useful in assessing whether its request for confidentiality should be granted: See item 8 above. Note that the equipment for which approval is being sought will be employed in applications that inherently carry a premium on security. Respectfully: Keven Trach Vice President, Projects

6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 2110 Single Limited Modular Transmitter Integration, Usage Limitations, and Grant Comments Scope This document identifies the integration requirements and usage limitations of the 2110 Single Limited Modular Transmitter as required by FCC 15.212 and KDB 996369. Pertinent grant comments as identified in KDB 821551 are also identified Integration Requirements 1. The 2110 Single Limited Modular Transmitter (2110 Module) shall be used PLUS Location Systems USA, LCC (PLUS), for integration into its own host devices. The 2110 Module shall not be sold or otherwise provided to third parties for integration into other devices. Third parties are prohibited from modifying the 2110 Module or integrating the 2110 Module into any host device. 2. Integration requirements provided herein shall be strictly followed by PLUS when incorporating the 2110 Module into any host device. 3. The 2110 Module includes an integrated antenna which shall not be modified as part of the integration into host devices. 4. The 2110 Module circuit board and active hardware components that determine transmitted signal radio parameters (such as output power and frequency) shall not be modified as part of the integration process into host devices. 5. The 2110 Module shall operate from a nominal 3 VDC power source provided by the host device. When integrated into the host product, the 2110 Module shall not be modified to operate at other voltages. 6. The 2110 Module shall be integrated into a host device utilizing an enclosure to provide physical protection for the internal components. The 2110 Module shall not rely on properties of the host device enclosure to meet emission limitations. The host device enclosure may vary in size, thickness and material type provided that all grant limitations are maintained. 7. The 2110 Module transmit signal characteristics shall not be controlled or modified by any external interface or user input mechanism. 8. The 2110 Module transmit signal characteristics shall not be controlled or modified by any autonomous (internally software managed) process. 9. The 2110 Module shall be labelled with its FCC ID number. 10. All 2110 Module host devices shall include a label identifying the FCC ID of the internal 2110 Module. 6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 11. All 2110 Module host devices shall comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion. Grant Comments 1. The 2110 Module and any host device shall comply with transmitted power limits as identified in FCC 15.519 (i.e. in-band EIRP not to exceed -41.3 dBm/MHz). As the 2110 Module has been lab tested for compliance with the 15.519 limits, and no user controls or modifications to the transmitted signal are enabled, compliance with these limits is maintained. 2. The 2110 Module includes an integrated antenna. The host device shall not provide a mechanism for disconnecting, changing, or bypassing the integrated antenna. 3. The 2110 Module and host device duty cycle factor shall be limited by factory firmware settings. 4. The 2110 Module and host devices may not be employed for the operation of toys. 5. Operation onboard an aircraft, a ship or a satellite is prohibited.

55 44 33 22 11 D D C C B B A A SEAN MINER BLOCK DIAGRAM SEAN MINER OOK MODULATED 50 Ohm Feed FET POWERCONTROL PIC16F689MICRO-CONTROLLER PROGRAMMING PINS ULPWUTIMER 3 VOLTBATTERY USART DATACLK LOGIC TOCOMBINEDATA & CLK BURST OSCILLATOR TransmitterControl EncodedData/Clk UWBANTENNA 2 MHz Pulse Rate PULSE SHAPING NETWORK 8 MHzCRYSTAL Revision History Date REV Initial Release 04/28/2014 A 04/28/201404/28/2014 Project Size
Document Number Rev Date: Sheet of ORIGINATORENGINEERAPPROVEDRELEASED THIS DESIGN AND PRINT IS THE PROPERTY OF PLUS LOCATION SYSTEMS THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION ANDIS LOANED IN CONFIDENCE. THIS DOCUMENTIS SUBJECT TO RETURN UPON DEMAND ON THE EXPRESSCONDITION THAT IT WILL NOT BE USED IN ANY WAY NOTAUTHORIZED BY PLUS LOCATION SYSTEMS. APPROVALS DATE Sheet Title 20S-0254 A PLUS 2110 UWB TAG MODULE B 1 3 6767 OLD MADISON PIKE SUITE 310 Huntsville, AL 3580 6 Thursday, May 22, 2014 Project Size
Document Number Rev Date: Sheet of ORIGINATORENGINEERAPPROVEDRELEASED THIS DESIGN AND PRINT IS THE PROPERTY OF PLUS LOCATION SYSTEMS THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION ANDIS LOANED IN CONFIDENCE. THIS DOCUMENTIS SUBJECT TO RETURN UPON DEMAND ON THE EXPRESSCONDITION THAT IT WILL NOT BE USED IN ANY WAY NOTAUTHORIZED BY PLUS LOCATION SYSTEMS. APPROVALS DATE Sheet Title 20S-0254 A PLUS 2110 UWB TAG MODULE B 1 3 6767 OLD MADISON PIKE SUITE 310 Huntsville, AL 3580 6 Thursday, May 22, 2014 Project Size
Document Number Rev Date: Sheet of ORIGINATORENGINEERAPPROVEDRELEASED THIS DESIGN AND PRINT IS THE PROPERTY OF PLUS LOCATION SYSTEMS THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION ANDIS LOANED IN CONFIDENCE. THIS DOCUMENTIS SUBJECT TO RETURN UPON DEMAND ON THE EXPRESSCONDITION THAT IT WILL NOT BE USED IN ANY WAY NOTAUTHORIZED BY PLUS LOCATION SYSTEMS. APPROVALS DATE Sheet Title 20S-0254 A PLUS 2110 UWB TAG MODULE B 1 3 6767 OLD MADISON PIKE SUITE 310 Huntsville, AL 3580 6 Thursday, May 22, 2014

6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 August 26, 2014 Travil Thul Office of Engineering and Technology Federal Communications Commission Re: FCC ID: ZEH0414 Applicant: PLUS Location Systems USA, LLC Correspondence Reference Number: 46280 Form 731 Confirmation Number: EA470317 Mr. Thul, Please find additional information in response to each of the discrepancies identified in your email on 8/13/2014. 1) The frequency range listed within the technical specification on form 731 shows a low frequency of 6.9274 MHz and a high frequency of 7.7567 MHz. It is understood that these values should be 6927.4 MHz and 7756.7 MHz (i.e. 6.9 GHz and 7.7 GHz). Please verify and update as appropriate. I attempted to correct the values to indicate a low frequency of 6927.4 MHz and a high frequency of 7756.7 MHz. However the website would not allow me to make any changes to form 731 once it has been submitted. 2) The test report and user manual indicates compliance with 15.519(3)(c), 15.519(3)(d), and 15.519(3)(b). It is understood that compliance with 15.519(c), 15.519(d), and 15.519(b) was intended. Please verify and update as appropriate. The test report and user manual have been corrected to indicate compliance with 15.519(c), 15.519(d), and 15.519(b). 3) Section 3 of the EMC test report indicates emission measurements below 1 GHz, applying limits from what is understood to be 15.519(c) (and 15.209 by reference). However, these limits are bound to a high frequency of 960 MHz. Due to variations in limits and measurement techniques above and below 960 MHz, please ensure that the EMC report does not present measurements which are not applicable (i.e. between 960 MHz and 1 GHz using procedures intended for use below 960 MHz). 6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 4) Per 15.519(a)(1), ‘a UWB device operating under the provisions of this section shall transmit only when it is sending information to an associated receiver. The UWB intentional radiator shall cease transmission within 10 seconds unless it receives an acknowledgement from the associated receiver that is transmission is being received’. Please submit supporting documentation describing how this requirement is fulfilled. The UWB transmitter operates as part of a system in which it sends short duration UWB packets to one or more receivers. The transmitter’s cycle of operation is as follows: 1) the transmitter’s microcontroller begins in a non-transmitting sleep state, 2) the transmitter transitions to an active state, in which it sends a short UWB packet of fixed duration of 101 microseconds, 3) the transmitter microcontroller ceases the transmission and returns to a sleep state. An oscilloscope screen capture of the 101 microsecond packet is shown in the figure below. Figure 2. UWB Packet. Each line is a 2 nanosecond pulse. Per the 15.519(a)(1) requirement, the UWB transmitter is allowed to operate up to 10 seconds after which it must cease its transmission if it has not received an acknowledgement from the associated receiver. As demonstrated, the UWB transmitter will automatically cease its transmission after only 101 microseconds, meeting the required behavior in much less than the allowed 10 seconds. 6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 5) Per 15.521(a) and consistent with Draft KDB Publication 821551 DR01, specific restrictions of usage should be reflected within the grant notes. Accordingly, grant notes reflecting that this EUT may not be employed for the operation of toys, operated onboard an aircraft, a ship, or a satellite have been added. No further action is required. 6) It is understood that this grant of authorization is intended to be as a Single Modular transmitter. As such, the pertinent exhibits required under Part I of KDB Publication 996369 D01 must be submitted. A link to this document is below. KDB Publication 996369 D01: http://appsint.fcc.gov/kdb/GetAttachment.html?id=cIpbiLbTdDomywhbMgK6ng%3D%3D Please reference attachment “Transmitter Module Equipment Authorization.pdf” for supporting documentation. 7) Consistent with #6, the 15.212 itemized list information appears to be included with the user manual. This information must be submitted as part of requirements outlined in KDB Publication 996369 D01. The user manual has been updated to be consistent with the attachment referenced above. In the original revision (Rev A), the user manual referenced many requirements that are specific to Single Modular Transmitters. The updated manual clarifies that the module is a Single Limited Modular Transmitter, and addresses the appropriate requirements. Sincerely, Keven Trach Vice President of Projects 6767 Old Madison Pike Suite 310 Huntsville, AL 35806 P: +1 256-217-4072 M:+1 256-428-6388 www.pluslocation.com

6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 August 26, 2014 Office of Engineering and Technology Federal Communications Commission Re: FCC ID: ZEH0414 Applicant: PLUS Location Systems USA, LLC Correspondence Reference Number: 46280 Form 731 Confirmation Number: EA470317 To whom it may concern, This correspondence addresses information required as part of the request for a modular grant of FCC ID ZEH0414, as described in KDB Publication 996369 D01. Scope The approval request is for a Limited Single-Modular Transmitter approval for a device with FCC ID ZEH0414. Limitations for Third Parties As a Limited Single-Modular Transmitter, the integration of the module and qualification of each host device product will be controlled by PLUS Location Systems USA, LLC (PLUS). PLUS will only sell or provide completed host products to third parties. PLUS will not provide modules to third parties or enable third parties to integrate the modules. Note that a contract manufacturer building products according to PLUS’ specifications is considered to be working under the direction of PLUS, not as an independent third party. Software Control and Software Defined Radios For clarification, this device is not a Software Defined Radio (SDR). Additionally, no software parameters are accessible or controllable to set power levels or other characteristics of the device that influence compliance. Host Product Compliance Any host product equipment functions not associated with the transmitter module (such as unintentional radiator elements) will be independently tested for compliance. Testing of the host product will be performed with the module installed and operational. 6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 Module as a Printed Wiring Assembly (PWA) The Limited Module is implemented as a physical Printed Wiring Assembly (PWA) with two electrical connections; a ground connection and 3V DC power. Non-Accessible Module The Limited Module integrated into the host device will not be accessible or replaceable by end users. Integration Instructions PLUS will maintain product assembly documentation for the Limited Module and host products for use by itself and its contract manufacturer. The Limited Module will not be made available to third parties for integration. Sincerely, Keven Trach Vice President of Projects 6767 Old Madison Pike Suite 310 Huntsville, AL 35806 P: +1 256-217-4072 M:+1 256-428-6388 www.pluslocation.com

6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 September 23, 2014 Travil Thul Office of Engineering and Technology Federal Communications Commission Re: FCC ID: ZEH0414 Applicant: PLUS Location Systems USA, LLC Correspondence Reference Number: 46280 Form 731 Confirmation Number: EA470317 Mr. Thul, Please find additional information in response to each of the discrepancies identified in your email on 8/27/2014. 1) Form 731 must be updated to reflect Limited Single Modular approval. This has been completed internally and no further action is required. O.E.T has completed this. 2) Per KDB Publication 996369 D01, detailed and comprehensive integration instructions, which must be provided to the integrator, must also be submitted as a separate exhibit. These instructions must allow for any associated party to clearly understand the conditions and limitations for authorized uses of the module. Please reference exhibit “2110 Single Limited Modular Transmitter Integration, Usage Limitations, and Grant Comments.pdf” for supporting documentation. 3) Per KDB Publication 9963969 D01, the responsible party must demonstrate how it will retain control over the final installation of the device, such that compliance of the product is ensured by limiting the installation to a specific host or hosts. (This content should be more expansive than what is provided in the Transmitter Module Equipment Doc exhibit.) Please reference exhibit “2110 Single Limited Modular Transmitter Integration, Usage Limitations, and Grant Comments.pdf” for supporting documentation. 6767 Old Madison Pike NW, Suite 310, Huntsville AL 35806 Main: 256.217.4072 Fax: 256.964.7614 4) Per KDB Publication 996369 D01, when the grant is issued, it shall state the device description modular type and, if applicable, the limiting conditions of the authorization. Please ensure that grant notes meet these criteria. Examples of pertinent grant notes can be found in KDB Draft Publication 821551 (link below). Please reference exhibit “2110 Single Limited Modular Transmitter Integration, Usage Limitations, and Grant Comments.pdf” for supporting documentation. Sincerely, Keven Trach Vice President of Projects 6767 Old Madison Pike Suite 310 Huntsville, AL 35806 P: +1 256-217-4072 M:+1 256-428-6388 www.pluslocation.com

SCALE 2 : 1 USE ZEBRA FINT STYLE "R" USE ZEBRA FINT STYLE "Q" USE ZEBRA FONT STYLE "R" BARCODE 0mm 0.000in 1.8mm 0.07in 4.7mm 0.19in 7.4mm 0.29in 10.4mm 0.41in 6.4mm 0.25in 12.7mm 0.50in 0mm 0.000in 15.9mm 0.63in 31.8mm 1.25in NOTES: DRAWING IS TO PROVIDE A TEMPLATE OF REQUIRED INFORMATION FOR FINAL TAG ASSEMBLIES THAT 1. USE THE 2110 TAG MODULE CIRCUIT. IF THE FINAL TAG REQUIRES A DIFFERENT GRAPHICS OR OUTLINE FORMAT THE INFORMATION LISTED MUST BE INCLUDED. TO BE PRINTED ON A ZEBRA THERMAL TRANSFER PRINTER 105SL 300dpi VERSION (P/N 10500-3001-0000 2. OR EQUIVALENT). USE TDC P/N 044-0017-9 FOR PRINTER RIBBON. BAR-CODE TO BE CODE 128A WITH A MINIMUM BAR HEIGHT OF 0.14 AND A BAR RATIO OF 3:1.3. DUE TO CONSTRAINTS RESULTING FROM THE PWA ASSEMBLY AND SERIALIZATION PROCESS THE TAG 4. UNIT SERIALIZATION DOES NOT FOLLOW THE CONCEPT SPECIFIED IN PLUS DOCUMENT NUMBER 450- 0005 "SERIALIZATION GUIDELINES" WHICH IS TYPICAL FOR PLUS LOCATION ASSEMBLIES. THE PWA IS PROGRAMMED WITH AN 8-DIGIT HEX CHARACTER STRING. THOSE EIGHT CHARACTERS ARE TO PRINTED ON THE SERIAL NUMBER LABEL IN BOTH BAR-CODE AND HUMAN READABLE FORM. PRINTED LABEL IS AN OUTPUT OF SOFTWARE P/N 150-0067 "Software, PLUS TAG Functional Test"5. SPECIFIC INFORMATION FOR MODEL NUMBER ARE LISTED ON THE UNIT ASSEMBLY DRAWING FOR THE 6. FINAL PRODUCT (100 LEVEL DRAWING). SCALE 5:1 APPROXIMATE LOCATION OF TEXT. RoHS COMPLIANCE NOTE: ALL MATERIALS, INKS, ADHESIVES, OVERLAMINATES AND PROCESSES USED TO PRODUCE THIS LABEL SHALL COMPLY WITH THE EU DIRECTIVE 2002/95/EC ON THE RESTRICTION OF THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN ELECTRICAL AND ELECTRONIC EQUIPMENT (RoHS). SUPPLIER SHALL ALSO RETAIN DOCUMENTATION SUPPORTING RoHS COMPLIANCE ACCORDING TO THEIR STANDARD OPERATING PROCEDURES. ANY DEVIATIONS FROM THIS REQUIREMENT MUST BE OBTAINED IN WRITING FROM PLUS LOCATION SYSTEMS. REVISIONS ZONEREV.DESCRIPTIONDATEAPPROVED ~AINITIAL RELEASE2014/5/28JA 6767 OLD MADISON PIKE NW SUITE 310 HUNTSVILLE, AL 35806 USA 320-0305 3rd ANGLE PROJECTION DO NOT SCALE DRAWING THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLUS LOCATION SYSTEMS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF PLUS LOCATION SYSTEMS IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL PRIMARY DIMENSIONS ARE IN MILLIMETERS TOLERANCES: ANGULAR: MACH BEND ONE PLACE DECIMAL TWO PLACE DECIMAL THREE PLACE DECIMAL MATERIAL FINISH MAKE FROM P/N 044-0037-9 COMMENTS: DATE NAME TITLE: SIZE B PART NUMBER REV SCALE: 5:1 UNLESS OTHERWISE SPECIFIED JOE ANDERSON5/28/2014 Label, PLUS TAG S/N SHEET 1 OF 1 A .01 .005 .0005 SECONDARY DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: TWO PLACE DECIMAL THREE PLACE DECIMAL FOUR PLACE DECIMAL 0.3 0.15 0.015 1.0 0.50.5 A-05 DRAWN BY DESIGNED BY JOE ANDERSON5-28-2014

Cummings Research Park 6767 Old Madison Pike, Suite 310 Huntsville AL 35806 P: +1 256-217-4072 M:+1 256-964-7614 www.pluslocation.com May 20, 2014 Theory of Operation / Technical Description The PLUS tracking system is a Real-Time Location System (RTLS) based on Ultra Wideband (UWB) technology. Its primary use is for the location and identification of people or objects. The system operates using active tags, a network of sensors (receivers), and one or more Synchronization Distribution Panels (SDPs). Sensor: The PLUS sensors are receive-only devices that are permanently mounted in the area of coverage. The sensors listen for and decode data packets from the tag, and also ascertain the time of arrival of the packet. Synchronization Distribution Panel: The synchronization distribution panel (SDP) distributes a timing signal to the multiple sensors in order that the times of arrival measured by each have a common time base. The SDP additionally powers the sensors over Ethernet cable, and passes the decoded data and measured times of arrival to other Ethernet devices. Tag, PLUS Model Number 2110 (FCC ID: ZEH0414): The Tag is a small, transmit-only device with an active transmit duty cycle of less than 0.0026%. The Tag has one integrated antenna optimized for vertical applications. The data packets include a tag identification code, status information, and time of arrival data.

Test Report Number: 3477563EMC01 Rev:2 PLUS Location Systems / UWB Tag Page: 1 of 24 Remarks: This report details the results of the testing carried out on one sample, the results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or Testing done by SGS International Electrical Approvals in connection with…

Text truncated - open the document above for the full version.