ZGBPMNA-02PT-PEN (Dongle)

1 PT-PEN Installation Guide All contents of this publication are subject to change. 2011.06 2 Information to user : This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause unacceptable interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. ᆞReorient or relocate the receiving antenna. ᆞIncrease the separation between the equipment and receiver. ᆞConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. ᆞConsult the dealer or an experienced Radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 3 INDEX 1. Check contents inside ---- 3 2. Install receiver station on laptop ---- 3 3. Product Specification ---- 6 4. Install driver software(MINT Control) ---- 7 4 Hardware Installation Guide 1. Check contents inside Please check to see if entire contents are included in package. If not, please contact customer service nearby or store. Station Pen Install CD Deco Fixture Both-side adhesive tapes 2. Install receiver station on laptop (1) <Place deco fixture underneath the receiver> Deco fixture – magnetic Place deco fixture underneath the receiver and check attaching position Deco fixture ※Station has a magnet. Keep away from magnetic sensitive objects such as credit card (2) < Placed the station in the middle > • Install in the middle section of laptop screen • Make sure station position with screen without tilting. • When right and left section of screen is not activated, place station a little higher than present position. • If there is a knob in the middle, place station on either right or left side. 5 (3) < Install on laptop screen > • Take off the masking tape on the back side of deco fixture. Attach deco fixture on top, right or left side of laptop cover. ※ please confirm station position setting in option menu of driver software (MINT Control). (4) < Connect USB > • Plug USB connector to USB port of PC. • When PC is on after installation, blue light will show on station and PC will automatically recognize device. (5) < Store separated from computer > Keep separate from PC when not being used. When being used, you can attach station to deco fixture. You can keep station attached for a while after use. 6 If S/W is not installed, proper operation may not occur even device is successfully installed. Please refer to “Software Installation” section of installation guide and install driver software. < How to confirm whether pen is active > • Upon inserting batteries, press pen tip or pen button in order to activate. • The pen is properly activated, small beep sound created from ultrasonic wave will occur in very close distance to ear. (Some may be insensitive to the sound since beep is significantly small) • When the pen does not operate properly, or pen cursor jitters terribly. - Please check whether dirt or stain is on pen battery or not. If it is so, remove it completely and operate again. - Insert new battery in case of discharge or inferiority (Discharged or inferior battery might be contained white power or deformed bulgy). < Auto Power-off (Sleep) mode > • When pen does not click within 30 seconds after last click, pen will be automatically initiated economical power-off mode. < Pen tip and Pen button functions > • Pen tip operates same as left button of mouse. • Lower pen button operates same as left button of mouse/upper pen button operates same as right button of mouse. • Change the Mint Control to Table Mode if you are using the product on a flat surface. (It can be used on normal flat surface. You can change the tip to ball pen to write on the paper.) 7 3. Product Specification Operating size 170mm ~ 358mm diagonal ( 16 inch ) Te c h n o l o g y Ultrasonic and infrared Sampling rate Over 70Hz Device standard HID pen device Resolution About 600 DPI (Sampling) / Valid with 0.2mm CPU Over 1 GHz RAM Over 512 MB WINDOWS OS Wondows XP / Vista (32bit) Interface USB port / CD-ROM driver Operating Temperature / Humidity 0~40 C / 20~ 80 % RH Storage Temperature / Humidity -20~60°C / 20~90% RH Station Power source DC 5V (USB) Power consumption 320mW Station Size / Weight (W)77mm X (D)58mm X (H)8.5mm / about 17g Pen Power source Li-Polymerl battery (55mAh) Power consumption 11mW Pen Size / Weight (W)130 X (D)16.5 / App. 17.5g(including pen tip, batteries) Pen Lifetime Lifetime in does not work – App.7 months Lifetime in normal usage – App. 1 months (1 hours continuous use per day) 8 Software Installation Guide 1. Install driver software (MINT Control) (1) Insert installation CD into CD-ROM. (2) Installation menu (picture below) will be appeared automatically. Start software installation by selecting “Install” MINT Control. <Old version> Launch You can use MINT Interactive without installing on your computer. Install Install MINT software on your computer Permanently. <New version> Install Install MINT software on your computer permanently. ; ※ when installation menu is not appeared automatically,…

Text truncated - open the document above for the full version.

PT-PEN(PMNA-02) Block diagram PNF Station MIC_R SPM0204UD5-6 MIC_L SPM0204UD5-6 IrDA module Thermistor STATION 7pin Connector MCU ARGOS X-Tal 4.8MHz EEPROM AT24C02B USB 7pin Connector USB connector LDO 3.3V PC

(PLEASE TYPE THIS LETTER ON YOUR COMPANY(applicant) LETTERHEAD) Date: September 20, 2011 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize J.H. Lee / Senior Engineer of IST Co., Ltd. and hereafter referred to as IST Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by J.H. Lee / Senior Engineer of IST Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing IST Co., Ltd. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, (Choon-Gu. Kim / Deputy Manager) (Penandfree) REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 1 of 2 IST(02) 029 A4 모(101025) The Photos of Equipment Under Test Front View Rear View IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 2 of 2 IST(02) 029 A4 모(101025) The Photos of Equipment Under Test Inner View

IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 1 of 2 IST(02) 029 A4 모(101025) Label Information Label Location

IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 1 of 3 IST(02) 029 A4 모(101025) The Photos of Equipment Under Test Inner View Inner View IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 2 of 3 IST(02) 029 A4 모(101025) Inner View Inner View IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 3 of 3 IST(02) 029 A4 모(101025) Inner View Inner View

IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 2 of 14 IST(02) 029 A4 모(101025) TABLE OF CONTENTS Table of contents 2 Information of test laboratory, Environmental conditions, Power supply system used, Product information 3 Descriptions of test 4-5 Conducted Emission 4 Radiated Emission 5 Equipment Under Test 6-7 Summary 8 ■ Test Conditions and Data - Emissions ◆ Conducted Emissions 0.15 MHz - 30 MHz Applicable Test Conditions / Data and Plots 9-11 ◆ Radiated Emissions 30 MHz - 1 GHz Applicable Test Conditions / Data and Plots 12-14 Note: IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 3 of 14 IST(02) 029 A4 모(101025) INFORMATIONS OF TEST LABORATORY IST Co., Ltd. 400-19, Singal-dong, Giheung-gu, Yongin-si, Kyonggi-Do, 446-599, Korea TEL : +82 31 326 6700 FAX : +82 31 326 6797 KOLAS Testing No. : 118 RRA Designation No. : KR0018 FCC Registration No. : 400603 FCC(DoC) Registration No. : 801060 VCCI Member No. : 1739 POWER SUPPLY SYSTEM USED Power supply system 120 V, 60 Hz (Refer to the product information) PRODUCT INFORMATION Station size 77 mm x 59 mm Sampling rate Over 70 Hz Windows OS Windows XP/Vista(32 bit) Interface USB port Pen Optional Power consumption 320 mW(Station) Power source DC 5 V for USB(Station) * Internal clock frequency is less than 108 MHz. - EMC suppression device is not used during the test . - Please refer to user’s manual. IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 4 of 14 IST(02) 029 A4 모(101025) < Concept Drawing > 215 >150 >40 80 Receiver EUT LISN 80  80 80 40  80 Measuring apparatus Mains Filter Mains Front side Equipment under test Coaxial cable Artificial mains network Screened room Non-metallic support 80 DESCRIPTIONS OF TEST Conducted Emissions: The measurement were performed over the frequency range of 0.15 MHz to 30 MHz using a 50 Ω /50uH LISN as the input transducer to a Spectrum Analyzer or a Field Intensity Meter. The measurements were made with the detector set for "Peak" amplitude within a bandwidth of 10KHz or for "quasi-peak" & “Average” within a bandwidth of 9 KHz. - Procedure of Test The line-conducted facility is located inside a shielded room No.1. A 1 m X 1.5 m wooden table 80 cm height is placed 40 cm away from the vertical wall and 1.5 m away from the other wall of the shielded room. The R/S ESH3-Z5 and Hyup-Rip KNW-407 LISN are bonded to bottom of the shielded room. The EUT is located on the wooden table with distance more than 80 cm from the LISN and powered from the Hyup-Rip LISN. The peripheral equipment is powered from the other LISN. Power to the LISNs are filtered by a noise cut power line filters. All electrical cables are shielded by braided tinned steel tubing with inner  1.2 cm. If the EUT is a DC-powered device, power will be derived from the source power supply it normally will be powered from and this supply lines will be connected to the Hyup-Rip LISN. All interconnected cables more than 1 m were shortened by non-inductive bundling to a 1 m length. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating conditions. The RF output of the LISN was connected to the R/S receiver to determine the frequency producing the maximum emission from the EUT. The frequency producing the maximum level was reexamined using Quasi-Peak mode by manual measurement, after scanned by automatic Peak mode for frequency range from 0.15 to 30 MHz. The bandwidth of the receiver was set to 10 kHz. The EUT, peripheral equipment, and interconnecting cables were arranged and manipulated to maximize each EME emission. < Side View > IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 5 of 14 IST(02) 029 A4 모(101025) DESCRIPTION OF TEST Radiated Emissions: The measurement was performed over the frequency range of 30 MHz to 1 GHz using antenna as the input transducer to a Spectrum analyzer or a Field Intensity Meter. The measurement was made with the detector set for "quasi-peak" within a bandwidth of 120 KHz. - Procedure of Test Preliminary measurements were made at 3 meter using bi-conical and log-periodic antennas, and spectrum analyzer to determine the frequency producing the max. emission in anechoic chamber. Appropriate precaution was taken to ensure that all emission from the EUT were maximized and investigated. The system configuration, mode of operation, turn-table azimuth and height with respect to the antenna were noted for each frequency found. The spectrum was scanned from 30 MHz to 300 MHz using S/B bi-conical antenna and 300 to 1000 MHz using S/B log-periodic antenna. Above 1 GHz, linearly polarized double ridge horn antennas were used. Final measurements were made at open site with 10- meters test distance using S/B bi-log antenna or horn antenna. The OATS have been verified in regular for its normalized site attenuation. The test equipment was placed on a wooden table. Sufficient time for the EUT, peripheral equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. Each frequency found during pre-scan measurements was re-examined by manual. The detector function was set to CISPR quasi-peak mode and the bandwidth of the receiver was set to 120 kHz or 1 MHz depending on the frequency of type of signal. The EUT, peripheral equipment and interconnecting cables were re-configured to the set-up producing the max. emission for the frequency and were placed on top of a 0.8-meter high nonmetallic 1 x 1.5 meter table. The EUT, peripheral equipment, and interconnecting cables were re-arranged and manipulated to maximize each emission. The turntable containing the system was rotated; the antenna height was varied 1 to 4 meters and stopped at the azimuth or height producing the maximum emission. Each emission was maximized by: varying the mode of operation to the EUT and/or peripheral equipment and changing the polarity of the antenna, whichever determined the worst-case emission. Control Room Receiver Control Room Receive r EUT 3 m 3 m IST C…

Text truncated - open the document above for the full version.

IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 1 of 2 IST(02) 029 A4 모(101025) Appendix A. The Photos of Test Setup Conducted Emissions – Front View Conducted Emissions – Rear View IST Co., Ltd. TEST REPORT NO. : 11-IST-0554 2 of 2 IST(02) 029 A4 모(101025) Appendix A. The Photos of Test Setup Radiated Emissions –Front View Radiated Emissions –Rear View