ZJ5BSMBB08Bluetooth Optical Mouse

2. Insert two AAA size batteries. Make sure the polarity is correct. 3. Close the battery box cover, and turn the power switch ON. 1. Press the connect button on the back of the mouse unit. (The status LED lights red) 3. Double-click the icon of this product. If this product is not recognized as a Bluetooth device, check the following items. Is this product able to communicate? Is the Bluetooth adaptor LED lit/flashing? Is it placed in a suitable location? Are there any obstructions between the product and the computer? Check each of the points above, and click [Search Devices] again. Frequency band 2.4GHz ModulationGFSK Assumed interference range 10m or less Advisability of frequency change Entire bandwidth is being used, and use of the same bandwidth as the “in-plant wireless station” or “specified low power wireless station” is unavoidable Follow the instructions below to prevent this product from interfering with the equipment or wireless stations listed above: 1. Make sure there are no in-plant wireless stations or specified low power wireless stations for mobile object identification operating in the vicinity before using this product. 2. Should this product cause radio wave interference with an in-plant wireless station for mobile object identification, immediately change the location where this product is used, or stop radio wave emission to avoid radio wave interference. 3. Please contact our Support Center for any other problems such as radio wave interference with a specified low power wireless station for mobile object identification caused by this product. Non-magnetic material (wooden desk etc) Approx. 10m Magnetic material (Iron desk etc) Approx. 3m Values are obtained via our in-house tests and are not guaranteed values. Radio Wave RangeRadio Wave Range PIN Code (Pass Key)PIN Code (Pass Key) The procedure below is based on Windows 7, but the procedure is the same for other operating systems. The procedure below assumes the use of the iBuffalo BSHSBD04 Bluetooth adaptor. If you are using a different Bluetooth device, consult the manual of that device. The procedure below assumes the use of the specialized driver for the iBuffalo BSHSBD04 Bluetooth adaptor, downloaded from the iBuffalo website. For Bluetooth ver2.0 or earlier, you may be requested a PIN code (pass key). In this case, enter “0000”. Sleep Mode Sleep Mode This product enters sleep mode after approximately 8 minutes. It recovers from sleep mode when moved. Computer Setting ProceduresComputer Setting Procedures This section explains the setting procedure for use with a PS3®. Setting Procedure for PS3®Setting Procedure for PS3® (1) In PS3 menu → [Settings] → [Accessory Settings], press the button. Status LED IndicatorStatus LED Indicator (5) This product is displayed in the [Bluetooth] screen. Quit the [Bluetooth] screen. (2) In [Manage Bluetooth devices], press the button. (5) [Scanning] is displayed for a while. (7) After [Please wait] is displayed, [Pairing complete] is displayed. (6) When the scan is completed, [Buffalo Bluetooth Optical Mouse] is displayed. With [Buffalo Bluetooth Optical Mouse] selected (flashing), press the button. (3) Select [Yes], and press the button. (4) Press the connect button on the back of the mouse unit (the status LED lights red), and then press the button in [Start Scanning]. (8) When the connection is completed normally, a blue mark lights on the left side of [Buffalo Bluetooth Optical Mouse]. This completes the pairing operation. Click the button to exit. (1) Press the button to display the options menu. If the mouse does not operate If the blue mark on the left side of the product name in the PS3® [Manage Bluetooth devices] screen is not lit, the device (mouse) is only registered, but not connected. Configure the connection settings using the procedure below. (4) When the connection is completed normally, a blue mark lights on the left side of [Buffalo Bluetooth Optical Mouse]. This completes the pairing operation. Click the button to exit. (2) Select [Connect] in the options menu, and press the button. (3) [Bluetooth device can connect when operated] is displayed. Click the mouse and press the button. 4. When the following window is displayed, click [Connect]. 5. Check that the [Status] is [Connected], and click [×] to close the window. 6. When this product is connected, the Bluetooth icon in the task tray changes from white to green . 2. Select [Start] – [All Programs] – [Bluetooth] – [My Bluetooth], and the window below is displayed. Click [Search Devices] at the top of the screen to search for this product. ●Instruction manual (this document) 1 ●AAA alkaline batteries 2 For operation check 1. Open the battery box cover on the underside of the mouse unit. Check the Package ContentsCheck the Package Contents How to Use this ProductHow to Use this Product Before using this product, check the package contents, names of parts and supported operating systems, and product specifications on the packaging. If anything is missing from the packaging, contact your vendor. A Bluetooth adaptor (dongle) is not included in this package. Use the Bluetooth function equipped as standard in your computer, or purchase a Buffalo Bluetooth adaptor (BSHSBD04 series etc). Caution When opening the battery box cover, be careful not to damage your fingernails or injure yourself. Caution The provided batteries are for testing operation of the device only, and may have run down since the device was shipped from the factory. You should therefore prepare new batteries as soon as possible, and replace the provided batteries with the new ones. Precautions with Regards to Radio Waves Do not use this product in the following places: Near a microwave oven where magnetic field, static electricity or radio disturbance occurs. In the vicinity of objects using radio waves of approximately 2.4GHz (the radio waves may not reach depending on the environment.) This product uses the same radio channel frequency as th…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT

R33093 ESD-XXXXXXXC NTC ID: Wor Tor XXXX FCC ID: ZJ5BSMBB08 Bluetooth Optical Mouse iDA ID:NXXXX-XX 08669/POSTEL/2008 2347 20421/SDPPI/2011 CCAI11LP1700T0 CMIIT ID: XXXXDJXXXX S&E 8 36MM 18MM

Page 2 Page 3 Page 4 Page 5 Page 6

FCC ID: ZJ5BSMBB08 Report No.: RF110804C19 Operational Description The transmitter of the EUT (Wireless Mouse) is powered from 3Vdc from batteries. The antenna is copper trace antenna without antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: SA990712C17A Report Format Version 4.0.0 Reference No.: 110804C19 1 RF EXPOSURE REPORT REPORT NO.: SA990712C17A MODEL NO.: BSMBB08 FCC ID: ZJ5BSMBB08 APPLICANT: Buffalo Kokuyo Supply Inc. ADDRESS: AKAMONDORI Bldg., 30-20, Ohsu 3-chome, Naka-ku, Nagoya. Aichi, 460-8315, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 5 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA990712C17A Report Format Version 4.0.0 Reference No.: 110804C19 2 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................. 3 1. CERTIFICATION.................................................................................................................. 4 2. REDUCED CONDITION FOR SAR ..................................................................................... 5 3. MAXIMUM MEASURED POWER OF EUT.......................................................................... 5 4. CONCLUSION ..................................................................................................................... 5 Report No.: SA990712C17A Report Format Version 4.0.0 Reference No.: 110804C19 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Sep. 02, 2011 Report No.: SA990712C17A Report Format Version 4.0.0 Reference No.: 110804C19 4 1. CERTIFICATION PRODUCT: Bluetooth Optical Mouse MODEL NO.: BSMBB08 BRAND: iBUFFALO APPLICANT: Buffalo Kokuyo Supply Inc. TESTED: Aug. 27 ~ Aug. 30, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: BSMBB08) have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Sep. 02, 2011 Polly Chien / Specialist APPROVED BY : , DATE :Sep. 02, 2011 Gary Chang / Technical Manager Report No.: SA990712C17A Report Format Version 4.0.0 Reference No.: 110804C19 5 2. REDUCED CONDITION FOR SAR When output power is ≤ 60/f(GHz) mW, SAR evaluation is not required. 3. MAXIMUM MEASURED POWER OF EUT Conducted power (dBm) Antenna Gain (dBi) EIRP (dBm) Threshold for SAR (dBm) 2.95 1.07 4.02 13.84 4. CONCLUSION No SAR evaluation is required since output power of EUT is less than threshold of SAR.

Report No.: RF990712C17A 1 Report Format Version 4.0.0 Reference No.: 110804C19 FCC TEST REPORT REPORT NO.: RF990712C17A MODEL NO.: BSMBB08 FCC ID: ZJ5BSMBB08 RECEIVED: Aug. 04, 2011 TESTED: Aug. 27 ~ Aug. 30, 2011 ISSUED: Sep. 02, 2011 APPLICANT: Buffalo Kokuyo Supply Inc. ADDRESS: AKAMONDORI Bldg., 30-20, Ohsu 3-chome, Naka-ku, Nagoya. Aichi, 460-8315, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 55 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF990712C17A 2 Report Format Version 4.0.0 Reference No.: 110804C19 Table of Contents RELEASE CONTROL RECORD................................................................................................ 4 1. CERTIFICATION............................................................................................................. 5 2. SUMMARY OF TEST RESULTS .................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY.................................................................................. 6 3. GENERAL INFORMATION ............................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................... 7 3.2 DESCRIPTION OF TEST MODES ................................................................................. 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................................ 8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................. 9 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................. 10 3.4 DESCRIPTION OF SUPPORT UNITS ......................................................................... 10 4. TEST TYPES AND RESULTS .......................................................................................11 4.1 RADIATED EMISSION MEASUREMENT .....................................................................11 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT...................................................11 4.1.2 TEST INSTRUMENTS.................................................................................................. 12 4.1.3 TEST PROCEDURES .................................................................................................. 13 4.1.4 DEVIATION FROM TEST STANDARD......................................................................... 13 4.1.5 TEST SETUP................................................................................................................ 14 4.1.6 EUT OPERATING CONDITIONS ................................................................................. 14 4.1.7 TEST RESULTS ........................................................................................................... 15 4.2 NUMBER OF HOPPING FREQUENCY USED ............................................................ 24 4.2.1 LIMIT OF HOPPING FREQUENCY USED................................................................... 24 4.2.2 TEST INSTRUMENTS.................................................................................................. 24 4.2.3 TEST PROCEDURES .................................................................................................. 24 4.2.4 DEVIATION FROM TEST STANDARD......................................................................... 25 4.2.5 TEST SETUP................................................................................................................ 25 4.2.6 TEST RESULTS ........................................................................................................... 25 4.3 DWELL TIME ON EACH CHANNEL ............................................................................ 28 4.3.1 LIMIT OF DWELL TIME USED ..................................................................................... 28 4.3.2 TEST INSTRUMENTS.................................................................................................. 28 4.3.3 TEST PROCEDURES .................................................................................................. 28 4.3.4 DEVIATION FROM TEST STANDARD......................................................................... 28 4.3.5 TEST SETUP................................................................................................................ 29 4.3.6 TEST RESULTS ........................................................................................................... 29 4.4 CHANNEL BANDWIDTH .............................................................................................. 37 Report No.: RF990712C17A 3 Report Format Version 4.0.0 Reference No.: 110804C19 4.4.1 LIMITS OF CHANNEL BANDWIDTH ........................................................................... 37 4.4.2 TEST INSTRUMENTS.................................................................................................. 37 4.4.3 TEST PROCEDURE..................................................................................................... 37 4.4.4 DEVIATION FROM TEST STANDARD......................................................................... 37 4.4.5 TEST SETUP................................................................................................................ 37 4.4.6 EUT OPERATING CONDITION.......................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST