ZMOL716LALTE Module

L716-LA Hardware Guide V1.5 Contact Information Website: https://www.fibocom.com Address: 10/F-14/F, Block A, Building 6, Shenzhen International Innovation Valley, Dashi First Road, Xili Community, Xili Subdistrict, Nanshan District, Shenzhen Tel: 0755-26733555 Safety Instructions Do not operate wireless communication products in areas where the use of radio is not recommended without proper equipment certification. These areas include environments that may generate radio interference, such as flammable and explosive environments, medical devices, aircraft or any other equipment that may be subject to any form of radio interference. The driver or operator of any vehicle shall not operate wireless communication products while controlling the vehicle. Doing so will reduce the driver's or operator's control and operation of the vehicle, resulting in safety risks. Wireless communication devices do not guarantee effective connection under any circumstances, such as when the (U) SIM card is invalid or the device is in arrears. In an emergency, please use the emergency call function when the device is turned on, and ensure that the device is located in an area with sufficient signal strength. Contents Copyright © Fibocom Wireless Inc. 1 Contents Applicable Models ............................................................................................. 4 Change History .................................................................................................. 5 1 Foreword ......................................................................................................... 6 1.1 Declaration ......................................................................................................................6 1.2 Reference standard .......................................................................................................6 2 Product Overview ........................................................................................... 8 2.1 Product Introduction ....................................................................................................8 2.2 Product Characteristics ................................................................................................8 2.3 Hardware Architecture .............................................................................................. 10 2.4 ADP & EVB Description .............................................................................................. 11 3 Pin Definition ................................................................................................ 12 3.1 Pin Distribution ............................................................................................................ 12 3.2 Pin Details ..................................................................................................................... 13 4 Application Interfaces .................................................................................. 20 4.1 Power supply ................................................................................................................ 20 4.1.1 Electrical Specifications ....................................................................................... 20 4.1.2 Power Input ........................................................................................................... 20 4.1.3 Power Output ........................................................................................................ 22 4.2 Power-on/off ................................................................................................................ 23 4.3 Reset .............................................................................................................................. 25 4.4 USB ................................................................................................................................. 27 4.5 UART ............................................................................................................................... 28 4.6 SPI ................................................................................................................................... 30 4.7 I2C ................................................................................................................................... 31 4.8 SDIO ............................................................................................................................... 31 4.9 RMII ................................................................................................................................ 33 4.10 PCM .............................................................................................................................. 34 4.11 SIM ............................................................................................................................... 35 4.12 ADC .............................................................................................................................. 40 Contents Copyright © Fibocom Wireless Inc. 2 4.13 Status Indicator ......................................................................................................... 41 4.14 Flight Mode ................................................................................................................ 42 4.15 Sleep Mode ................................................................................................................ 43 5 Antenna Interfaces....................................................................................... 45 5.1 Antenna Interface ...................................................................................................... 45 5.2 RF Band ......................................................................................................................... 45 5.3 RF Antenna ................................................................................................................... 46 5.3.1 Antenna …

Text truncated - open the document above for the full version.

Rev 1/26/2023 (APPLICANT’S COMPANY LETTERHEAD) Fibocom Wireless Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 11-20-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: (ZMOL716LA) [Insert applicant name] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Patrick Ma Rev 1/26/2023 (APPLICANT’S COMPANY LETTERHEAD) Fibocom Wireless Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: mm-dd-yyyy Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: (ZMOL716LA) [Insert applicant name] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Patrick Ma

Fibocom Wireless Inc. 1101, Tow er A, Building 6, Shenzhen International, Innovation Valle y, Dashi 1st Rd, Nanshan, ShenZhen, China Tel: +8675526733555 ; Fax: +86-755-26520841 Federal Communications Commission 7435 Oaklan d Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, [Fibocom Wireless Inc. Grantee Code ZMO, FRN:0020891057] (“the applicant”) certifies that, as of the date of the filing of application, [Fibocom Wireless USA] (“the agent”) is designated as the U.S. agent for the purpose of accepting service of process on behalf of the applicant. The information of agent are: U.S. Agent: Fibocom Wireless USA FCC Registration Number (FRN): 0033437914 Physical U.S. address: 5909 Peachtree Dunwoody Rd Ste 910 Atlant a, GA 30328 United States Contact: Lei Yao Phone: +01 (469)463-6983 Email: [email protected] The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The agent accepts the designation by (the applicant) as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Signed by the Applicant Signed by the Agent Name: Patrick Ma Email: [email protected] Date: April 21, 2023 Name: Lei Yao Email: [email protected] Date: April 21, 2023

Rev 11/20/07 (APPLICANT’S LETTERHEAD) Fibocom Wireless Inc. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: (ZMOL716LA). Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram, Schematics, Operational Description, Parts List, Tune Up Info Block Diagram, Schematics, Operational Description, BOM Tune Up The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Sincerely, (signature) (printed name) Patrick Ma

The letter must be on the applicant’s letterhead and signed by the grantee code contact. D:\CCC,SRRC,NAL_Project\L716-LA-00-00\FCC\FCC 文件\Modular Approval Letter_140225.docx Revision: 140225 Page 1 of 2 Approved By: G Greene MODULAR APPROVAL LETTER Modular Approval Requirement Yes (i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Yes, please see exhibition external photos (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. Yes, the modular has buffer modulation/data inputs (iii) The modular transmitter must have its own power supply regulation. Yes, please see the schematics (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a ‘‘unique’’ antenna coupler (at all connections between the module and the antenna, including the cable). The ‘‘professional installation’’ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Yes, the requirements of antenna connector and spurious emission have been fulfilled. Please refer to the test report. (v) The modular transmitter must be tested in a stand- alone configuration Yes, please refer to the setup photos (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. Yes, the module will be label with it own FCC ID, and the instruction on the labeling rule of the end product has been stated in the user manual of this module. (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Yes, the required FCC rule has been fulfilled and all the instruction for maintaining compliance have been clearly stated in the user manual (viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Yes, please refer exhibition RF exposure of MPE RF exposure rule. The letter must be on the applicant’s letterhead and signed by the grantee code contact. D:\CCC,SRRC,NAL_Project\L716-LA-00-00\FCC\FCC 文件\Modular Approval Letter_140225.docx Revision: 140225 Page 2 of 2 Approved By: G Greene Name and surname of applicant(or authorized representative): Date: 11/20/2023 Name: Patrick Ma Signature:

D:\CCC,SRRC,NAL_Project\L716-LA-00-00\FCC\FCC 文件\POA_Letter.docx (Must be on Company Letter head Stationary) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: SUBJECT: FCC Application for (ZMOL716LA) To Whom It May Concern: We, the undersigned, hereby authorize __Jim Huang____ at _ Sushi TOWE Wireless Testing(Shenzhen)Co.,Ltd.__________________ on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by ___Jim Huang____ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, (Must be signed by the person that is listed on the FCC Website)

Sushi TOWE Wireless Testing (Shenzhen) Co., Ltd. Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Page 1 / 1 External Photos

Sushi TOWE Wireless Testing (Shenzhen) Co., Ltd. Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Page 1 / 1 Internal Photos

Sushi TOWE Wireless Testing (Shenzhen) Co., Ltd. Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. TEST REPORT Applicant: FIBOCOM Wireless Inc EUT Description: LTE Module Model: L716-LA Brand: Fibocom FCC ID: ZMOL716LA Standards: FCC 47 CFR Part 2.1091 Date of Receipt: 2023/10/27 ~ 2023/11/15 Date of Issue: 2023/11/16 TOWE. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. the results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. It is the manufacturer's responsibility to assure that additional production units of the model are manufactured with identical electrical and mechanical components. All sample tested were in good operating condition throughout the entire test program. Measurement Uncertainties are published for informational purposes only and were not taken into account unless noted otherwise. without written approval of TOWE, the test report shall not be reproduced except in full. Approved By: Reviewed By: Page 2 / 8 Report No.: TSWA2023100000703 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Revision History Rev. Issue Date Description Revised by 01 2023/11/16 Original 陈呈福 Page 3 / 8 Report No.: TSWA2023100000703 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Table of Contents 1 General Description .............................................................................................................................. 4 1.1 Lab Information ...................................................................................................................... 4 1.1.1 Testing Location ................................................................................................................ 4 1.1.2 Test Facility / Accreditations ............................................................................................. 4 1.2 Client Information ................................................................................................................... 4 1.2.1 Applicant ............................................................................................................................ 4 1.2.2 Manufacturer ..................................................................................................................... 4 1.3 General Description of EUT................................................................................................... 5 2 Maximum Permissible RF Exposure ................................................................................................... 6 2.1 RF Exposure Limit Introduction ........................................................................................... 6 2.2 Equations ................................................................................................................................ 7 3 RF Exposure Results ............................................................................................................................ 8 3.1 Standalone Exposure Calculations ...................................................................................... 8 Page 4 / 8 Report No.: TSWA2023100000703 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. 1 General Description 1.1 Lab Information 1.1.1 Testing Location These measurements tests were conducted at the Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. facility located at F401 and F101, Building E, Hongwei Industrial Zone, Liuxian 3rd Road, Bao'an District, Shenzhen, China. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014 Tel.: +86-755-27212361 Contact Email: [email protected] 1.1.2 Test Facility / Accreditations A2LA (Certificate Number: 7088.01) This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017). FCC Designation No.: CN1353 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. has been recognized as an accredited testing laboratory. Designation Number: CN1353. ISED CAB identifier: CN0152 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0152 Company Number: 31000 1.2 Client Information 1.2.1 Applicant Applicant: Fibocom Wireless Inc. Address: 1101, Tower A, Building 6, Shenzhen Internatio…

Text truncated - open the document above for the full version.

Page 1 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Effective (Isotropic) Radiated Power Output Data Test Result Band Channel Result(dBm) ERP (dBm) Limit(dBm) Verdict GSM85012832.4031.57 38.45PASS GSM85019032.6131.78 38.45PASS GSM85025133.1532.32 38.45PASS Band Channel Slot Result(dBm) ERP(dBm) Limit(dBm) Verdict EGPRS850128126.4625.63 38.45PASS EGPRS850128226.2325.4 38.45PASS EGPRS850128323.0022.17 38.45PASS EGPRS850128422.8522.02 38.45PASS EGPRS850190126.3125.48 38.45PASS EGPRS850190226.1425.31 38.45PASS EGPRS850190322.8922.06 38.45PASS EGPRS850190422.7221.89 38.45PASS EGPRS850251126.9026.07 38.45PASS EGPRS850251226.7325.9 38.45PASS EGPRS850251323.4722.64 38.45PASS EGPRS850251423.3522.52 38.45PASS Band Channel Result(dBm) EIRP(dBm) Limit(dBm) Verdict GSM190051230.1532.08 33.00PASS GSM190066130.0932.02 33.00PASS GSM190081030.4132.34 33.00PASS Band Channel Slot Result(dBm) EIRP(dBm) Limit(dBm) Verdict EGPRS1900512125.3727.3 33.00PASS EGPRS1900512225.2727.2 33.00PASS EGPRS1900512321.2423.17 33.00PASS EGPRS1900512421.1723.1 33.00PASS EGPRS1900661125.4927.42 33.00PASS EGPRS1900661225.4327.36 33.00PASS EGPRS1900661321.5023.43 33.00PASS EGPRS1900661421.4623.39 33.00PASS EGPRS1900810125.7227.65 33.00PASS EGPRS1900810225.6927.62 33.00PASS EGPRS1900810321.7723.7 33.00PASS EGPRS1900810421.7323.66 33.00PASS Page 2 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Peak-to-Average Ratio(CCDF) Test Result Band Channel Result(dB) Limit(dB) Verdict GSM850 128 2.81 13 PASS GSM850 190 2.79 13 PASS GSM850 251 2.8 13 PASS EGPRS850 128 5.72 13 PASS EGPRS850 190 5.67 13 PASS EGPRS850 251 5.77 13 PASS GSM1900 512 2.8 13 PASS GSM1900 661 2.81 13 PASS GSM1900 810 2.78 13 PASS EGPRS1900 512 5.7 13 PASS EGPRS1900 661 5.67 13 PASS EGPRS1900 810 5.71 13 PASS Page 3 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Test Graphs GSM850-128-5-PASS GSM850-190-5-PASS GSM850-251-5-PASS EGPRS850-128-8-PASS EGPRS850-190-8-PASS EGPRS850-251-8-PASS Page 4 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. GSM1900-512-0-PASS GSM1900-661-0-PASS GSM1900-810-0-PASS EGPRS1900-512-2-PASS EGPRS1900-661-2-PASS EGPRS1900-810-2-PASS Page 5 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Appendix C: 26dB Bandwidth and Occupied Bandwidth Test Result Band Channel Occupied Bandwidth (MHz) 26dB Bandwidth (MHz) Limit (MHz) Verdict GSM850 128 0.24825 0.3155 --- PASS GSM850 190 0.24582 0.3201 --- PASS GSM850 251 0.24627 0.3194 --- PASS EGPRS850 128 0.24728 0.3112 --- PASS EGPRS850 190 0.24675 0.3136 --- PASS EGPRS850 251 0.24542 0.3085 --- PASS GSM1900 512 0.24567 0.3102 --- PASS GSM1900 661 0.24866 0.3204 --- PASS GSM1900 810 0.24498 0.3180 --- PASS EGPRS1900 512 0.24377 0.3086 --- PASS EGPRS1900 661 0.24476 0.3125 --- PASS EGPRS1900 810 0.24853 0.3124 --- PASS Page 6 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Test Graphs GSM850-128-5-PASS GSM850-190-5-PASS GSM850-251-5-PASS EGPRS850-128-8-PASS EGPRS850-190-8-PASS EGPRS850-251-8-PASS Page 7 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. GSM1900-512-0-PASS GSM1900-661-0-PASS GSM1900-810-0-PASS EGPRS1900-512-2-PASS GSM1900-661-0-PASS GSM1900-810-0-PASS Page 8 / 36 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. EGPRS1900-661-2-PASS EGPR…

Text truncated - open the document above for the full version.

Page 1 / 28 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Effective (Isotropic) Radiated Power Output Data Test Result Band Bandwidth Modulation Channel RB Configuration Result(dBm) EIRP(dBm) Limit(dBm) Verdict Band2 1.4MHz QPSK 18607 1RB#0 23.91 25.84 33.00 PASS Band2 1.4MHz QPSK 18607 1RB#2 24.17 26.1 33.00 PASS Band2 1.4MHz QPSK 18607 1RB#5 24.09 26.02 33.00 PASS Band2 1.4MHz QPSK 18607 6RB#0 23.87 25.8 33.00 PASS Band2 1.4MHz QPSK 18900 1RB#0 24.16 26.09 33.00 PASS Band2 1.4MHz QPSK 18900 1RB#2 23.98 25.91 33.00 PASS Band2 1.4MHz QPSK 18900 1RB#5 24.06 25.99 33.00 PASS Band2 1.4MHz QPSK 18900 6RB#0 23.54 25.47 33.00 PASS Band2 1.4MHz QPSK 19193 1RB#0 24.49 26.42 33.00 PASS Band2 1.4MHz QPSK 19193 1RB#2 24.26 26.19 33.00 PASS Band2 1.4MHz QPSK 19193 1RB#5 24.22 26.15 33.00 PASS Band2 1.4MHz QPSK 19193 6RB#0 23.78 25.71 33.00 PASS Band2 1.4MHz 16QAM 18607 1RB#0 23.78 25.71 33.00 PASS Band2 1.4MHz 16QAM 18607 1RB#2 24.08 26.01 33.00 PASS Band2 1.4MHz 16QAM 18607 1RB#5 23.64 25.57 33.00 PASS Band2 1.4MHz 16QAM 18607 6RB#0 23.34 25.27 33.00 PASS Band2 1.4MHz 16QAM 18900 1RB#0 23.71 25.64 33.00 PASS Band2 1.4MHz 16QAM 18900 1RB#2 23.66 25.59 33.00 PASS Band2 1.4MHz 16QAM 18900 1RB#5 23.6 25.53 33.00 PASS Band2 1.4MHz 16QAM 18900 6RB#0 23.06 24.99 33.00 PASS Band2 1.4MHz 16QAM 19193 1RB#0 24.12 26.05 33.00 PASS Band2 1.4MHz 16QAM 19193 1RB#2 23.88 25.81 33.00 PASS Band2 1.4MHz 16QAM 19193 1RB#5 24.03 25.96 33.00 PASS Band2 1.4MHz 16QAM 19193 6RB#0 23.2 25.13 33.00 PASS Band2 3MHz QPSK 18615 1RB#0 24.56 26.49 33.00 PASS Band2 3MHz QPSK 18615 1RB#8 23.76 25.69 33.00 PASS Band2 3MHz QPSK 18615 1RB#14 23.81 25.74 33.00 PASS Band2 3MHz QPSK 18615 15RB#0 23.55 25.48 33.00 PASS Band2 3MHz QPSK 18900 1RB#0 23.89 25.82 33.00 PASS Band2 3MHz QPSK 18900 1RB#8 23.34 25.27 33.00 PASS Band2 3MHz QPSK 18900 1RB#14 23.42 25.35 33.00 PASS Band2 3MHz QPSK 18900 15RB#0 23.06 24.99 33.00 PASS Band2 3MHz QPSK 19185 1RB#0 24.77 26.7 33.00 PASS Band2 3MHz QPSK 19185 1RB#8 23.84 25.77 33.00 PASS Band2 3MHz QPSK 19185 1RB#14 24.82 26.75 33.00 PASS Band2 3MHz QPSK 19185 15RB#0 23.6 25.53 33.00 PASS Band2 3MHz 16QAM 18615 1RB#0 24.03 25.96 33.00 PASS Band2 3MHz 16QAM 18615 1RB#8 23.24 25.17 33.00 PASS Page 2 / 28 Report No.: TSWA2023100000701 Sushi TOWE Wireless Testing(Shenzhen) Co., Ltd. Email: [email protected] Tel.: +86-755-27212361 TOWE-QP-15-F05 Rev.1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from TOWE. Band2 3MHz 16QAM 18615 1RB#14 24.13 26.06 33.…

Text truncated - open the document above for the full version.