ZMOSC208GLLTE Module

Rev 1/26/2023 Fibocom Wireless Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date:23-08-2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: ZMOSC208GL Fibocom Wireless Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) Patrick Ma Rev 1/26/2023 Fibocom Wireless Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 08-23-2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: ZMOSC208GL Fibocom Wireless Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) Patrick Ma

Fibocom Wireless Inc. 1101, Tow er A, Building 6, Shenzhen International, Innovation Valle y, Dashi 1st Rd, Nanshan, ShenZhen, China Tel: +8675526733555 ; Fax: +86-755-26520841 Federal Communications Commission 7435 Oaklan d Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, [Fibocom Wireless Inc. Grantee Code ZMO, FRN:0020891057] (“the applicant”) certifies that, as of the date of the filing of application, [Fibocom Wireless USA] (“the agent”) is designated as the U.S. agent for the purpose of accepting service of process on behalf of the applicant. The information of agent are: U.S. Agent: Fibocom Wireless USA FCC Registration Number (FRN): 0033437914 Physical U.S. address: 5909 Peachtree Dunwoody Rd Ste 910 Atlant a, GA 30328 United States Contact: Lei Yao Phone: +01 (469)463-6983 Email: [email protected] The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The agent accepts the designation by (the applicant) as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Signed by the Applicant Signed by the Agent Name: Patrick Ma Email: [email protected] Date: April 21, 2023 Name: Lei Yao Email: [email protected] Date: April 21, 2023

Fibocom Wireless Inc. Date: 2024.09.04 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: ZMOSC208GL Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operational Description 4. Schematics 5. Block Diagram 6. Operational Description Tune-up Procedure 17. Tune-up Procedure Bill(s) of Material 18. BOM The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature Patrick Ma

Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: ZMOSC208GL Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. YES, Please refer to External Photos. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. YES, SC208-GL is used for the function. 3. The modular transmitter must have its own power supply regulation. YES, the modular has its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). YES, it is Printed antenna. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, the module is tested in a stand-alone configuration as the test photos show. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). YES, please refer to the exhibition label sample for this module. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. YES, please refer to the user manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. YES, RF exposure statement is attached in the user manual. Items to be covered by Split modular transmitters. Answer from applicant 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Patrick Ma Date: 2024-08-23 Signature:

Fibocom Wireless Inc. Wi-Fi Channel 12 and 13 Declaration Letter Date: 2024-08-23 We, the undersigned company Company Name: Fibocom Wireless Inc. Address: 1101, Tower A, Building 6, Shenzhen International Innovation Valley, Dashi 1st Rd, Nanshan, Shenzhen, China Declare that: Product description: LTE Module Type designation: SC208-GL Brand: Fibocom FCC ID: ZMOSC208GL Only channels 1~11 will be used in USA. Country code selection is disabled. If you have any questions regarding the authorization, please do not hesitate to contact us, thank you~ Sincerely, Signature: ___ _____ Name: Patrick Ma Function: Certification Director

Fibocom Wireless Inc. Ad Hoc Mode Declaration Date: 2024-08-23 We, the undersigned company Company Name: Fibocom Wireless Inc. Address: 1101,Tower A, Building 6, Shenzhen International,Innovation Valley, Dashi 1st Rd, Nanshan, ShenZhen, China Declare that: Product description: LTE Module Type designation: SC208-GL Brand: Fibocom FCC ID: ZMOSC208GL 1. The EUT doesn’t have Ad Hoc Mode function on “non-US frequencies”. 802.11a/n Ad Hoc mode should not be supported even on US DFS frequencies (5.25 ~5.35GHz/5.47 ~5.725GHz). 2. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US. The product meets all other requirements specified in Part 15E Section 15.407 and no configuration controls are provided to change the frequency of operations outside the grant of certification for US operation. 3. Only channels 1~11 will be used in USA. Country code selection is disabled. If you have any questions regarding the authorization, please do not hesitate to contact us, thank you~ Sincerely, Signature: ____ ______ Name: Patrick Ma Tel: +8675526733555 Email: [email protected]

Fibocom Wireless Inc. Declaration of Authorization We Name: Fibocom Wireless Inc. Address: 1101,Tower A, Building 6, Shenzhen International Innovation Valley, Dashi 1st Rd, Nanshan City: ShenZhen Country: China Declare that: Name Representative of agent: Ms. Rose Liu Agent Company name: BTL Inc. Address: No.3 Jinshagang 1 st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s): Product description: LTE Module Type designation: SC208-GL Trademark: Fibocom FCC ID: ZMOSC208GL on our behalf. Date: 2024-08-23 City: ShenZhen Name: Patrick Ma Function: Certification Director Signature: ...... .........

Project No.: 2405G016 Page 2 of 4