ZOQ-PLAX21AVerizon Connect RFID reader

Oct 12, 2022 Page 1 of 10 Installation RFID Reader and Kit guide for pro installer partners 2 Product Overview 2 Important information 3 RFID I/O adapter harness 3 RFID card reader 3 New Vehicle Installation 3 Kit components 3 Mounting the RFID reader 4 Recommended RFID reader mounting locations 4 Installation steps 4 Connect the inline RFID adapter harness 5 Install the RFID reader 6 Download firmware updates 7 Verify installation 7 Hardware identification 8 Xirgo devices 8 RFID card reader 8 RFID I/O adapter harness 9 Webbed locking grommet 9 Disclaimer 10 Oct 12, 2022 Page 2 of 10 Installation RFID Reader and Kit guide for pro installer partners This installation guide provides comprehensive “before you get started” information. It is intended for Verizon Connect professional installer partners who are not yet familiar with installing this specific device or may need a review of such knowledge. Installers already well-versed in the installation of this specific device may opt to proceed to the Reveal Hardware Installer app and follow the process outlined there. Product Overview The Verizon Connect 125kHz PLA-X21RFID card reader device reads data from an HID ISO PROXII RFID card when held within close proximity. Card data is transferred to the connected Xirgo VTU device using 1WIRE/DS1990 Emulation mode. The Verizon Connect125kHz PLA-X21RFID card reader has an operating frequency from 110kHz to 125kHz. The Xirgo XT-6300 series VTU (Vehicle Tracking Unit) is used to collect and transmit vehicle based data (position, speed, heading, acceleration, etc..) as part of our software as a service fleet management product. The Verizon Connect125kHz PLA-X21RFID card readerdevice provides the means to include HID ISO PROXII RFID card data with the transmitted vehicle based data Oct 12, 2022 Page 3 of 10 Important information RFID I/O adapter harness 1. Use the RFID I/O adapter harness when performing 4G RFID card reader upgrades and any 3G migration swap installations. Do not use this adaptor for new vehicle installations. 2. The RFID I/O adapter harness does not replace the existing I/O harness. It installs in-line between the Xirgo and the existing I/O harness, and allows technicians to complete installations without re-making I/O and power connections. ● Technicians must verify the existing device wiring is in good operating condition and perform wire repairs as necessary. This includes all 3 wire and PTO trigger wire connections. RFID card reader 1. RFID reader installation requires increasing the existing Driver ID reader’s pass through hole to 1” in diameter. A 1 in. hole saw may be easier to control than a 1-1/8th inch Unibit or standard drill bit. If you accidentally drill the diameter 1/8” too large the grommet will not seat in the hole. Use a safe method you are comfortable with and always look before you drill. ● If the existing Driver ID reader’s mounting hole cannot be reused due to location or fit, then a new 1” hole must be drilled. ○ You must disconnect the iButton reader’s 2-pin Molex connector from the I/O harness so it doesn’t trip the buzzer after completing the installation. ○ Leave the old iButton reader mounted in place and secure the harness. New Vehicle Installation New vehicle installations will use the recently updated Xirgo I/O accessory harness released in August 2022. This harness has an integrated 6-pin connector that is compatible with the RFID reader. ● Do not use an RFID I/O adapter harness with a new vehicle installation. ● Connect Sensor Input 1 to the PTO trigger wire. The PTO switch is normally found in the center console and is marked AUX1 with a PTO sticker. ● The installation guide for new Xirgo installations including instructions for the RFID reader installation are available at install.verizonconnect.com. Kit components ● RFID Adapter Harness – Part # CBA-US-XIR-002-01-00 ● RFID Card Reader – Part # ● Alcohol wipes x 2 ● Velcro/VHB Tape x 1 ● Adhesive cable tie mount x 1 ● Locking Grommet x 1 A 4G Xirgo device will be shipped separately when a 3G swap is required. Oct 12, 2022 Page 4 of 10 Mounting the RFID reader Determine if you are able to reuse the existing Driver ID reader location. ● To reuse the existing hole, you must increase its diameter from 3/8” to 1”. You must also be able to Velcro/VHB mount the new RFID reader in a location convenient for the driver to reach with their RFID badge. ● If you are unable to reuse the location, leave the existing Driver ID reader mounted in place and choose a location based on the guidelines below. Don’t forget to disconnect the Driver ID reader’s 2 pin connector and secure or cut its cable. Recommended RFID reader mounting locations Location 1: Reuse the existing Driver ID hole to the right of the steering column whenever possible. Location 2: An empty space on a driver’s side hush panel. Location 3: Left side of the steering column if the other locations are not practical or available. Installation steps Refer to the Xirgo OBD-II Powered Y-cable installation guide if you are unfamiliar with installation of Xirgo devices or need a refresher. 1. Locate the existing Xirgo installation and perform the 3G swap if necessary. ● If you are performing a 3G swap, disconnect the 14-pin and 24-pin molex connectors from the 3G Xirgo device. Use snips to cut the mounting zip ties and remove the device. Then mount the 4G device in its place and proceed to the next step. Oct 12, 2022 Page 5 of 10 2. Disconnect the 2-pin iButton reader from the 24-pin I/O harness then disconnect the I/O harness from the Xirgo. Connect the inline RFID adapter harness 1. Connect the male end of the RFID I/O adapter harness to the existing I/O harness. To power the device, connect the female end to the Xirgo. ● The existing power connections, peripheral and sensor input connections are passed through to the Xirgo. Oct 12, 2022 Page 6 of 10 Install the RFID reader 1. Carefully create a 1” hole. - Look before you drill, be careful not to damage ad…

Text truncated - open the document above for the full version.

Form: RFT-AMER-TCB-OP-19n Revision: 1 Pa ge 1 of 1 Date: 1/25/2023 5055 North Point Parkway Deepak Kuttin Alpharetta, GA 30022 Tech Mgr-QA Test Automation Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist a nd 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applica nt: Verizon Connect Inc FCC ID: ZOQ-PLAX21A To whom it ma y concern, Verizon Connect Inc, Deepak Kuttin certifies that the equipment for which authoriz a t ion is so u gh t is n o t “covered” equipment prohibited from receiving a n equipment a uthorization pursuant to 47 CFR part §2 .903 of the FCC rules a nd does not origina te directly or indirectly from a ny company named on th e c o vere d list loca ted in the link a bove or a ny subsidiary or affilia te thereof. Applica nt further certifies that, as of the date of the filing of the a pplica tion, the Applicant is not identified on the Covered List a s a n entity producing “covered” equipment a nd is not a subsidiary or a ffilia te of a n y su c h entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I a m authorized to make the representations above on behalf of the Applicant a nd a gree to immediately notify Intertek if there is a ny change in the status identified above. Deepak Kuttin Tech Mgr-QA Test Automation Verizon Connect 08/28/2023

Form: RFT-AMER-TCB-OP-19o Revision: 1 Pa ge 1 of 1 Date: 1/25/2023 5055 North Point Parkway Deepak Kuttin Alpharetta, GA 30022 Tech Mgr-QA Test Automation Attention: Application Examiner Re: Certification designating a U.S. a gent for service of process pursuant to 47 CFR part §2.911(d)(7) of the FCC rules To whom it ma y concern, This letter is to certify that Verizon Connect Inc, Deepak kuttin (“Applicant”) accepts responsibilities t o a c t a s its own a gent pursuant to 47 CFR part §2.911(d)(7) of the FCC rules for service of process. I c o nsen t t o the obliga tion to a ccept service of process on behalf of the Applicant for all certification applicatio ns t o t h e FCC. I HEREBY CERTIFY THAT I a m authorized to make the representations above on behalf of the Applicant. I further a cknowledge the requirement to maintain an agent extends for no less than one year after the termination of a ll marketing and importation or the conclusion of a nd commission-related proceeding involving the equipment a nd agree to immediately notify the FCC a nd Intertek if there is a ny change in the sta tus identified above. Applicant Company Name : Verizon Connect Inc Contact Name : Deepa k kuttin Address : 5055 North Point Pkwy Alpha retta, GA 30328 Telephone No : 404-895-1220 Ema il : Deepa [email protected] Applicant FRN : 0019691732 FCC ID : ZOQ-PLAX21A Signature: Date: 09/21/2023

Form: RFT-AMER-TCB-OP-19o Revision: 1 Pa ge 1 of 1 Date: 1/25/2023 5055 North Point Parkway Deepak Kuttin Alpharetta, GA 30022 Tech Mgr-QA Test Automation Attention: Application Examiner Re: Certification designating a U.S. a gent for service of process pursuant to 47 CFR part §2.911(d)(7) of the FCC rules To whom it ma y concern, This letter is to certify that Verizon Connect Inc, Deepak kuttin (“Applicant”) accepts responsibilities t o a c t a s its own a gent pursuant to 47 CFR part §2.911(d)(7) of the FCC rules for service of process. I c o nsen t t o the obliga tion to a ccept service of process on behalf of the Applicant for all certification applicatio ns t o t h e FCC. I HEREBY CERTIFY THAT I a m authorized to make the representations above on behalf of the Applicant. I further a cknowledge the requirement to maintain an agent extends for no less than one year after the termination of a ll marketing and importation or the conclusion of a nd commission-related proceeding involving the equipment a nd agree to immediately notify the FCC a nd Intertek if there is a ny change in the sta tus identified above. Applicant Company Name : Verizon Connect Inc Contact Name : Deepa k kuttin Address : 5055 North Point Pkwy Alpha retta, GA 30328 Telephone No : 404-895-1220 Ema il : Deepa [email protected] Applicant FRN : 0019691732 FCC ID : ZOQ-PLAX21A Signature: Date: 09/21/2023

5055 North Point Parkway Deepak Kuttin Alpharetta, GA 30022 Tech Mgr-QA Test Automation 9/07/2023 Attention: Applica tion Examiner Re: Request for confidentiality Applica nt: Verizon Connect Inc. FCC ID: ZOQ-PLAX21A To whom it ma y concern, Perma nent Confidentiality Request is hereby submitted by Verizon Connect Inc. to with ho ld p erma ne ntly from public review certain portions of the a pplication for equipment certification f or t h e re f ere nc ed FC C identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) a nd 0.459 of the FCC Rules. In pa rticular, the following sections of the a pplication are to be kept permanently confidential: • Schematics • Deta iled Block dia grams • Deta iled Operational/Functional Description Ra tionale for request for confidentiality: Verizon Connect Inc. has invested considerable time and materials in resea rch a nd development to produce the referenced product. Disclosure of the permanently confidential portions of this a pplica tion to competitors would not only give them significant competitive advantages in developing simila r products, but would a lso disclose successful implementation of unpublished, lea ding edge technology developed by us. Our Schematics, Block Dia gram, a nd Detailed Operational/Functional Description a re designed for internal company use only; along with the use of professional installa tion these documents are very technical a nd are not provided to the consumer since the consumer ca nnot service the device. If you have questions or need further information, please contact the undersigned. Sincerely, Deepak Kuttin Tech Mgr-QA Test Automation Verizon Connect

5055 North Point Parkway Deepak Kuttin Alpharetta, GA 30022 Tech Mgr-QA Test Automation 8/28/2023 Intertek Testing Services NA Ltd. 70 Codman Hill Road Boxborough, MA 01719 Subject: Limited Agency Agreement Verizon Connect Inc. FCC ID: ZOQ-PLAX21 To Whom It May Concern: We, Verizon Connect, Inc., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number ZOQ-PLAX21 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is August 28, 2023. The Limited Agency Agreement expires on August 28, 2024, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Deepak Kuttin Tech Mgr-QA Test Automation Verizon Connect

Verizon Connect 125kHz PLA-X21 RFID card reader images 1 Verizon Connect 125kHz PLA-X21 RFID card reader images Verizon Connect 125kHz PLA-X21 RFID card reader images 2 Version Change Author Date 0.1 Initial draft Larry Kenney 12/02/2022 0.2 Final version Larry Kenney 12/05/2022 Verizon Connect 125kHz PLA-X21 RFID card reader images 3 Contents Revision History 2 Introduction 4 PLA-X21 Images 4-6 Verizon Connect 125kHz PLA-X21 RFID card reader images 4 Introduction This document provides images of the Verizon Connect 125kHz PLA-X21 RFID card reader. PLA-X21 Images VerizonConnect PLA-X21 Front VerizonConnect PLA-X21 Back VerizonConnect PLA-X21 Left Side Verizon Connect 125kHz PLA-X21 RFID card reader images 5 PLA-X21 Images VerizonConnect PLA-X21 Right Side VerizonConnect PLA-X21 Top Verizon Connect 125kHz PLA-X21 RFID card reader images 6 PLA-X21 Images VerizonConnect PLA-X21 Bottom

REARFRONT MODEL: PLA-X21 S/N: XXXXXXX FCC ID: ZOQ-PLAX21A Made in Poland RFID Reader PLASTIC MOULDINGS: BLACK MATT TEXTURE. PAGE: 1 OF 2 DOCUMENT: CMF & ARTWORK SPECIFICATION PROJECT: VERIZON CONNECT RFID READER DAT E : 7th SEP 2023 Confidential and proprietary materials for authorized Verizon personnel and outside agencies only. Use, disclosure or distribution of this material is not permitted to any unauthorized persons or third parties except by written agreement. VERSION: 10 REAR MODEL: PLA-X21 S/N: XXXXXXX FCC ID: ZOQ-PLAX21A Made in Poland RFID Reader MODEL: PLA-X21 S/N: XXXXXXX FCC ID: ZOQ-PLAX21A Made in Poland RFID Reader MODEL: PLA-X21 S/N: XXXXXXX FCC ID: ZOQ-PLAX21A Made in Poland RFID Reader 2mm 50mm 14mm LABEL: WHITE GRAPHICS ON BLACK BACKGROUND. 25.4mm 50mm DUO LOCK VELCRO: 2” X 1” STRIP DOUBLE SIDED ONTO CENTRE OF REAR CASE. DUO LOCK VELCRO: SECOND 2” X 1” STRIP PROVID- ED WITH RFID READER FOR VEHICLE INSTALL. PAGE: 2 OF 2 DOCUMENT: CMF & ARTWORK SPECIFICATION PROJECT: VERIZON CONNECT RFID READER DAT E : 7th SEP 2023 Confidential and proprietary materials for authorized Verizon personnel and outside agencies only. Use, disclosure or distribution of this material is not permitted to any unauthorized persons or third parties except by written agreement. VERSION: 10

Interior side A: Interior side B:

RF EXPOSURE TEST REPORT Report Number: 105530563MPK-002 Project Number: G105530563 Report Issue Date: September 07, 2023 Revision Date: September 20, 2023 Equipment Tested: Verizon Connect RFID reader Model Tested: PLA-X21 Standards: ISED SPR-002 Issue 1 September 2016 Supplementary Procedure for Assessing Compliance with RSS-102 Nerve Stimulation Exposure Limits FCC KDB 447498 D04 (Interim General RF Exposure Guidance v01) Tested by: Client: Intertek Testing Services NA, Inc. 1365 Adams Court Menlo Park, CA 92630 USA Report prepared by VERIZON CONNECT, INC. 5055 North Point Parkway ALPHARETTA, GA 30009 USA Report reviewed by Gilberto Gallegos Rangel EMC Project Engineer Minh Ly EMC Team Lead This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Report Number: 105530563MPK-002 Issued: 09/20/2023 Non-Specific EMC Report Shell Rev. August 2015 Page 2 of 19 VERIZON CONNECT, INC. Model PLA-X21 Table of Contents 1 Introduction and Conclusion .............................................................................................................. 3 2 Test Summary ...................................................................................................................................... 3 3 Client Information ................................................................................................................................ 4 4 Description of Equipment Under Test and Variant Models ............................................................. 4 5 System Setup and Method .................................................................................................................. 5 6 Test Results .......................................................................................................................................... 6 7 Revision History ................................................................................................................................. 19 Report Number: 105530563MPK-002 Issued: 09/20/2023 Non-Specific EMC Report Shell Rev. August 2015 Page 3 of 19 VERIZON CONNECT, INC. Model PLA-X21 1 Introduction and Conclusion The tests indicated in section 2.0 were performed on the product constructed as described in section 4.0. The remaining test sections are the verbatim text from the actual d ata sheets used during the investigation. These test sections include the test name, the specified test Method, a list of the actual Test Equipment Used, documentation Photos, Results and raw Data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complies with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. Intertek does not make any claims of compliance for samples or variants which were not tested. 2 Test Summary Section Test full name Result 3 Client Information - 4 Description of Equipment Under Test and Variant Models - 5 System Setup and Method - 6 Test Results Compliant 7 Revision History - Report Number: 105530563MPK-002 Issued: 09/20/2023 Non-Specific EMC Report Shell Rev. August 2015 Page 4 of 19 VERIZON CONNECT, INC. Model PLA-X21 3 Client Information This EUT was tested at the request of: Client: VERIZON CONNECT, INC. 5055 North Point Parkway ALPHARETTA, GA 30009 USA Contact: Deepak Kuttin Email: [email protected] 4 Description of Equipment Under Test and Variant Models Manufacturer: VERIZON CONNECT, INC. 5055 North Point Parkway ALPHARETTA, GA 30009 USA Equipment Under Test Description Manufacturer Model Number Serial Number Verizon Connect RFID reader VERIZON CONNECT, INC. PLA-X21 0000292 Receive Date: 07/28/23 Test Started: 09/07/23 Received Condition: Good Test Completed: 09/07/23 Type: Production Description of Equipment Under Test (provided by client) The PLA-X21 is a 110kHz to 125kHz low power RFID card reader. Operating modes of the EUT: No. Description of EUT Exercising 1 The EUT was configured to continuously transmit and looking for tags. Variant Models: None Report Number: 105530563MPK-002 Issued: 09/20/2023 Non-Specific EMC Report Shell Rev. August 2015 Page 5 of 19 VERIZON CONNECT, INC. Model PLA-X21 5 System Setup and Method 5.1 Method: FCC: The RF device is exempt and compliant to RF exposure limit per FCC 1.1307(b)(3)(i)(A). INDUSTRY CANADA: Configuration as required by Annex E, para E1.1 Passively used Table top device of SPR-002 Supplementary Procedure for Assessing Compliance with RSS-102 Nerve Stimulation Exposure Limits and Radio Standards Specification RSS-102, Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus Radiofrequency radiation exposure evaluation: Measurements were performed on all sides of the device and the worst result is recorded. Measurement Uncertainty: Measurement uncertainty is estimated 2.0 dB for the coverage factor of 2. 5.2 EUT Block Diagram: EUT RFID Tag Air DC Power Supply 120VAC 60Hz Report Number: 105530563MPK-002 Issued: 09/20/2023 Non-Specific EMC Report Shell Rev. August 2015 Page 6 of 19 VERIZON CO…

Text truncated - open the document above for the full version.

EMC Verizon Connect, Inc. on Verizon Connect RFID Reader File: 105530563MPK-001 Page 1 of 28 TEST REPORT Report Number: 105530563MPK-001 Project Number: G105530563 Original Issued Date: August 15, 2023 Revised Date: September 15, 2023 Testing performed on the Verizon Connect RFID Reader Model Number: PLA-X21 to FCC Part 15 Subpart C (15.209) FCC Part 15, Subpart B Industry Canada RSS-210 Issue 10 Industry Canada ICES-003 For Verizon Connect, Inc. Test Performed by: Test Authorized by: Intertek 1365 Adams Court Menlo Park, CA 94025 USA Verizon Connect, Inc. 5055 North Point Parkway Alpharetta, GA 30009 USA Prepared by: Date: September 15, 2023 Kenneth Roque Reviewed by: Date: September 15, 2023 Minh Ly This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. This report must not be used to claim product endorsement by A2LA, NIST nor any other agency of the U.S. Government. EMC Verizon Connect, Inc. on Verizon Connect RFID Reader File: 105530563MPK-001 Page 2 of 28 Report No. 105530563MPK-001 Equipment Under Test: Verizon Connect RFID readers Model Number: PLA-X21 Serial Number: 0000292 Applicant: Verizon Connect, Inc. Contact: Deepak Kuttin Address: 5055 North Point Parkway Alpharetta, GA 30009 Country USA Email [email protected] Applicable Regulation: FCC Part 15 Subpart C (15.209) FCC Part 15, Subpart B Industry Canada RSS-210 Issue 10 Industry Canada ICES-003 Issue 7 Test Site Location: ITS – Site 1 1365 Adams Drive Menlo Park, CA 94025 Date of Test: July 28, 2023 We attest to the accuracy of this report: Kenneth Roque EMC Project Engineer Minh Ly EMC Team Lead EMC Verizon Connect, Inc. on Verizon Connect RFID Reader File: 105530563MPK-001 Page 3 of 28 TABLE OF CONTENTS 1.0 Summary of Tests .......................................................................................................................... 4 2.0 General Description ....................................................................................................................... 5 2.1 Product Description ............................................................................................................ 5 2.2 Related Submittal(s) Grants ................................................................................................ 6 2.3 Test Methodology ............................................................................................................... 6 2.4 Test Facility ........................................................................................................................ 6 2.5 Measurement Uncertainty ................................................................................................... 6 3.0 System Test Configuration ............................................................................................................ 7 3.1 EUT Photo .......................................................................................................................... 7 3.2 Block Diagram of Test Setup .............................................................................................. 8 3.3 Justification ......................................................................................................................... 9 3.4 Software Exercise Program................................................................................................. 9 3.5 Mode of Operation during test ............................................................................................ 9 3.6 Modifications required for Compliance .............................................................................. 9 3.7 Additions, deviations and exclusions from standards ......................................................... 9 4.0 Measurement Results................................................................................................................... 10 4.1 Field Strength of Fundamental and Radiated Emissions Outside the band ...................... 10 4.1.1 Requirements .................................................................................................... 10 4.1.2 Procedure .......................................................................................................... 11 4.1.3 Test Result ........................................................................................................ 12 4.1.5 Test Configuration Photographs ....................................................................... 14 4.2 Occupied Bandwidth ......................................................................................................... 16 4.2.1 Requirements .................................................................................................... 16 4.2.2 Procedure .......................................................................................................... 16 4.2.3 Test Results ....................................................................................................... 17 4.3 AC Line Conducted Emission .......................................................................................... 18 4.3.1 Requirement ........................................................…

Text truncated - open the document above for the full version.