ZPJ-WMICG4-HUWireless Microphone System

COBAN DSSS 900MHz Wireless Microphone System for Law Enforcement Owner’s Manual COBAN Technologies, Inc. 11375 West Sam Houston Parkway South Suite # 800 Houston, TX 77031 WWW.CobanTech.COm COBAN Wireless Microphone System Features Frequency: 902 to 925 MHz ; DSSS; Frequency Hopping Range: 1000 ft (Line-of-Sight) Receiver Module: Dual Receivers with Dual Separated Independent Antennas RS-485 communicating to the Host 12 VDC/500mA Transmitter: 1650 mAH/3.7V Rechargeable Li-Ion Battery (Transmitter) 10 Hours Talk Time Built-in microphone with optional Lavaliere external Microphone Optional External Antenna for Extended Distance One On-Air Button with Two Programmable Buttons Weatherproof THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE CONDITION THAT THIS DEVICE DOES NOT CAUSE HARMFUL INTERFERENCE . COBAN Technologies 2 COBAN Wireless Microphone System Overview Wireless Microphone Transmitter Transmitter Top View Transmitter Side View Trasmitter Bottom View Record Button Button 1 External Antenna Mic Button 2 Sync Contact COBAN Technologies 3 Wireless Microphone Receiver Sync Contact 1 Sync Contact 2 COBAN Technologies 4 COBAN Wireless Microphone System Operations 1. Locate the contacts at the bottom of the wireless mic. 2. Press the wireless microphone contacts directly on top of the receiver’s register contacts. NOTE: The receiver is located behind each of the front seats near nearest the door pillar. 3. A confirmation tone will sound to indicate the receiver and the microphone have synchronized their frequencies. 4. The wireless microphone is now on standby mode and ready for use. NOTE: Syncing a second microphone to the same receiver will replace and nullify the first microphone. Patrol Car Installation Diagram Record button COBAN Technologies 5 The large button on the Microphone will always be used to initiate Recording (Default: Front only) Status Indicators Programmable Button Functions 1. Mute – Toggle Audio Mute (does not affect Video) 2. Stop – Stop Video (Not Recommended) 3. Marker – Adds a bookmark to the video 4. AutoZoom – Performs AutoZoom on front camera 5. Partner Alert – Notifies other Microphone of emergency (double microphone units only) 6. Covert interview – Starts Rear Seat recording and black ‐ out monitor Toggle Covert Mode (Vibrate only) 1. Press the Record Button and center Program Button simultaneously for 2 seconds. Repeat action to enable LED and buzzer (normal) mode. Action/Alert Regular mode (Audio, LED & Vibrate) Covert mode (Vibrate Only) Toggle between Regular and Covert modes - hold down REC and Button 1 for two seconds Vibrates and beeps once when active Vibrates twice when active Record Beeps and vibrates Twice GREEN LED (w/o lapel mic) BLUE LED (w/ lapel mic ) Vibrates twice Low Signal / Out of Range YELLOW LED Beeps intermittently Vibrates intermittently Stop recording – press Button 1 or Button 2 Long beep and vibrate once Long vibrate once Mute - press Button 1 or Button 2 GREEN LED BLINKS Beeps and vibrates in interval Button 2 – vibrate once Button 3 – vibrate twice Continues to vibrate once in interval time frames Other Programmable functions- press Button 1 or Button 2 Button 2 – beep once Button 3 – beep twice Button 2 – vibrate once Button 3 – vibrate twice Panic - hold down REC Button for 3 seconds. RED LED On - beeps and vibrates 3 times Off - beeps and vibrates once On - vibrates 3 times Off - vibrates once Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digita l device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonab le protection against harmful interf erence in a reside ntial installation. This equipment generates, uses and can ra diate radio frequency energy and, if not inst alled and used in accordance with the ins tructions, may cause harmful interference to radio communications. However, ther e is no guarantee that interfer ence will not occur in a partic ular installation. If this equipment does cause harmful interferen ce to radio or television reception, which can be determined by turning the equipme nt off and on, the user is encouraged to try to correct th e interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outl et on a circuit different from that to which the receiver is connected. . Consult the dealer or an experien ced radio/TV technician for help. FCC Caution : To assure continued compliance, any cha nges or modifications not ex pressly approved by the party responsible for compliance could void the user's authority to operate th is equipment. (Example - use only shielded interface cables when connecting to com puter or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inte rference, and (2) This device must accept a ny interference received, including interf erence that may cause undesired operation.

COBAN DSSS 900MHz Wireless Microphone System for Law Enforcement Owner’s Manual COBAN Technologies, Inc. 11375 West Sam Houston Parkway South Suite # 800 Houston, TX 77031 WWW.CobanTech.COm COBAN Wireless Microphone System Features Frequency: 902 to 925 MHz ; DSSS; Frequency Hopping Range: 1000 ft (Line-of-Sight) Receiver Module: Dual Receivers with Dual Separated Independent Antennas RS-485 communicating to the Host 12 VDC/500mA Transmitter: 1650 mAH/3.7V Rechargeable Li-Ion Battery (Transmitter) 10 Hours Talk Time Built-in microphone with optional Lavaliere external Microphone Optional External Antenna for Extended Distance One On-Air Button with Two Programmable Buttons Weatherproof THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE CONDITION THAT THIS DEVICE DOES NOT CAUSE HARMFUL INTERFERENCE . COBAN Technologies 2 COBAN Wireless Microphone System Overview Wireless Microphone Transmitter Transmitter Top View Transmitter Side View Trasmitter Bottom View Record Button Button 1 External Antenna Mic Button 2 Sync Contact COBAN Technologies 3 Wireless Microphone Receiver Sync Contact 1 Sync Contact 2 COBAN Technologies 4 COBAN Wireless Microphone System Operations 1. Locate the contacts at the bottom of the wireless mic. 2. Press the wireless microphone contacts directly on top of the receiver’s register contacts. NOTE: The receiver is located behind each of the front seats near nearest the door pillar. 3. A confirmation tone will sound to indicate the receiver and the microphone have synchronized their frequencies. 4. The wireless microphone is now on standby mode and ready for use. NOTE: Syncing a second microphone to the same receiver will replace and nullify the first microphone. Patrol Car Installation Diagram Record button COBAN Technologies 5 The large button on the Microphone will always be used to initiate Recording (Default: Front only) Status Indicators Programmable Button Functions 1. Mute – Toggle Audio Mute (does not affect Video) 2. Stop – Stop Video (Not Recommended) 3. Marker – Adds a bookmark to the video 4. AutoZoom – Performs AutoZoom on front camera 5. Partner Alert – Notifies other Microphone of emergency (double microphone units only) 6. Covert interview – Starts Rear Seat recording and black ‐ out monitor Toggle Covert Mode (Vibrate only) 1. Press the Record Button and center Program Button simultaneously for 2 seconds. Repeat action to enable LED and buzzer (normal) mode. Action/Alert Regular mode (Audio, LED & Vibrate) Covert mode (Vibrate Only) Toggle between Regular and Covert modes - hold down REC and Button 1 for two seconds Vibrates and beeps once when active Vibrates twice when active Record Beeps and vibrates Twice GREEN LED (w/o lapel mic) BLUE LED (w/ lapel mic ) Vibrates twice Low Signal / Out of Range YELLOW LED Beeps intermittently Vibrates intermittently Stop recording – press Button 1 or Button 2 Long beep and vibrate once Long vibrate once Mute - press Button 1 or Button 2 GREEN LED BLINKS Beeps and vibrates in interval Button 2 – vibrate once Button 3 – vibrate twice Continues to vibrate once in interval time frames Other Programmable functions- press Button 1 or Button 2 Button 2 – beep once Button 3 – beep twice Button 2 – vibrate once Button 3 – vibrate twice Panic - hold down REC Button for 3 seconds. RED LED On - beeps and vibrates 3 times Off - beeps and vibrates once On - vibrates 3 times Off - vibrates once Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digita l device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonab le protection against harmful interf erence in a reside ntial installation. This equipment generates, uses and can ra diate radio frequency energy and, if not inst alled and used in accordance with the ins tructions, may cause harmful interference to radio communications. However, ther e is no guarantee that interfer ence will not occur in a partic ular installation. If this equipment does cause harmful interferen ce to radio or television reception, which can be determined by turning the equipme nt off and on, the user is encouraged to try to correct th e interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outl et on a circuit different from that to which the receiver is connected. . Consult the dealer or an experien ced radio/TV technician for help. FCC Caution : To assure continued compliance, any cha nges or modifications not ex pressly approved by the party responsible for compliance could void the user's authority to operate th is equipment. (Example - use only shielded interface cables when connecting to com puter or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inte rference, and (2) This device must accept a ny interference received, including interf erence that may cause undesired operation.

Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 2 of 28 External Photos Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 3 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 4 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 5 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 6 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 7 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 8 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 9 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 10 of 28

Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 2 of 28 External Photos Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 3 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 4 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 5 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 6 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 7 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 8 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 9 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 10 of 28

Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 11 of 28 Internal Photos Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 12 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 13 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 14 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 15 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 16 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 17 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 18 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 19 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 20 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 21 of 28

Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 11 of 28 Internal Photos Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 12 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 13 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 14 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 15 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 16 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 17 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 18 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 19 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 20 of 28 Registration number: W6M21304-13152-FCC FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Appendix Page 21 of 28

Report No：139135R-HPUSP10V01 Page: 1 of 23 FCC Test Report Product Name ：Wireless Microphone System Model No. ： WMICG4-HU Applicant ：Coban Technologies, Inc Address ：11375 W. Sam Houston Parkway S. # 800 Houston, TX. 77031 USA Date of Receipt ：2013/09/03 Issued Date ：2013/10/07 Report No. ：139135R-HPUSP10V01 Report Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of Quie Tek Corporation. Report No：139135R-HPUSP10V01 Page: 2 of 23 Test Report Certification Issued Date: 2013/10/07 Report No.: 139135R-HPUSP10V01 Product Name ： Wireless Microphone System Applicant ： Coban Technologies, Inc Address ： 11375 W. Sam Houston Parkway S. # 800 Houston, TX. 77031 USA Manufacturer ： Shenzhen Honmax Technology Limited Model No. ： WMICG4-HU FCC ID ： ZPJ-WMICG4-HU Applicable Standard ： FCC Oet65 Supplement C June 2001 IEEE Std. 1528-2003 47CFR § 2.1093 Measurement procedures ： KDB 447498 D01 & D02 , KDB 941225, KDB 865664 Test Result ： Max. SAR Measurement (1g) 0.626 W/kg Application Type ： Certification The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of Quie Tek Corporation. Documented By ： (Adm. Specialist / April Chen) Tested By ： (Engineer / Wen Lee) Approved By ： (Manager / Vincent Lin) Report No：139135R-HPUSP10V01 Page: 3 of 23 TABLE OF CONTENTS Description Page 1. General Information .............................................................................. 5 1.1 EUT Description ............................................................................................................5 1.2 Maximum output power and tolerance allowed for production units ............................ 5 1.3 Test Environment ...........................................................................................................6 2. SAR Measurement System ................................................................... 7 2.1 DASY5 System Description .......................................................................................... 7 2.1.1 Applications ................................................................................................................ 8 2.1.2 Area Scans................................................................................................................... 8 2.1.3 Zoom Scan (Cube Scan Averaging)............................................................................ 8 2.1.4 Uncertainty of Inter-/Extrapolation and Averaging .................................................... 8 2.2 DASY5 E-Field Probe ................................................................................................... 9 2.2.1 Isotropic E-Field Probe Specification ......................................................................... 9 2.3 Boundary Detection Unit and Probe Mounting Device ............................................... 10 2.4 DATA Acquisition Electronics (DAE) and Measurement Server ............................... 10 2.5 Robot .............................................................................................11 2.6 Light Beam Unit........................................................................................................... 11 2.7 Device Holder ..............................................................................................................12 2.8 SAM Twin Phantom .................................................................................................... 12 3. Tissue Simulating Liquid .................................................................... 13 3.1 The composition of the tissue simulating liquid .......................................................... 13 3.2 Tissue Calibration Result ............................................................................................. 13 3.3 Tissue Dielectric Parameters for Head and Body Phantoms........................................ 14 4. SAR Measurement Procedure ............................................................ 15 4.1 SAR System Check ...................................................................................................... 15 4.1.1 Dipoles ...................................................................................................................... 15 4.1.2 System Check Result ................................................................................................ 15 4.2 SAR Measurement Procedure ...................................................................................... 16 4.2.1 SAR Measurement Procedure ................................................................................... 16 5. SAR Exposure Limits .......................................................................... 17 6. Test Equipment List ............................................................................ 18 7. Measurement Uncertainty................................................................... 19 8. Conducted Power Measurement ........................................................ 20 9. Duty cycle............................................................................................. 20 10 Test Results.......................................................................................... 21 10.1 SAR Test Results Summary ....................................................................................... 21 Report No：139135R-HPUSP10V01 Page: 4 of 23 11. SAR measurement variability ............................................................ 22 Appendix .............................................................................................23 Appendix A. SAR System Check Data Appendix B. SAR measurement Data Appendix C. Test Setup Photographs & EUT Photographs Appendix D. Probe Calibration Data Appendix E. Dipole Calibration Data Report No：139135R-HPUSP10V01 Page: 5 of 23 1. General Information 1.1 EUT Description Prod…

Text truncated - open the document above for the full version.

Report No：139135R-HPUSP10V01 Page: 1 of 23 FCC Test Report Product Name ：Wireless Microphone System Model No. ： WMICG4-HU Applicant ：Coban Technologies, Inc Address ：11375 W. Sam Houston Parkway S. # 800 Houston, TX. 77031 USA Date of Receipt ：2013/09/03 Issued Date ：2013/10/07 Report No. ：139135R-HPUSP10V01 Report Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of Quie Tek Corporation. Report No：139135R-HPUSP10V01 Page: 2 of 23 Test Report Certification Issued Date: 2013/10/07 Report No.: 139135R-HPUSP10V01 Product Name ： Wireless Microphone System Applicant ： Coban Technologies, Inc Address ： 11375 W. Sam Houston Parkway S. # 800 Houston, TX. 77031 USA Manufacturer ： Shenzhen Honmax Technology Limited Model No. ： WMICG4-HU FCC ID ： ZPJ-WMICG4-HU Applicable Standard ： FCC Oet65 Supplement C June 2001 IEEE Std. 1528-2003 47CFR § 2.1093 Measurement procedures ： KDB 447498 D01 & D02 , KDB 941225, KDB 865664 Test Result ： Max. SAR Measurement (1g) 0.626 W/kg Application Type ： Certification The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of Quie Tek Corporation. Documented By ： (Adm. Specialist / April Chen) Tested By ： (Engineer / Wen Lee) Approved By ： (Manager / Vincent Lin) Report No：139135R-HPUSP10V01 Page: 3 of 23 TABLE OF CONTENTS Description Page 1. General Information .............................................................................. 5 1.1 EUT Description ............................................................................................................5 1.2 Maximum output power and tolerance allowed for production units ............................ 5 1.3 Test Environment ...........................................................................................................6 2. SAR Measurement System ................................................................... 7 2.1 DASY5 System Description .......................................................................................... 7 2.1.1 Applications ................................................................................................................ 8 2.1.2 Area Scans................................................................................................................... 8 2.1.3 Zoom Scan (Cube Scan Averaging)............................................................................ 8 2.1.4 Uncertainty of Inter-/Extrapolation and Averaging .................................................... 8 2.2 DASY5 E-Field Probe ................................................................................................... 9 2.2.1 Isotropic E-Field Probe Specification ......................................................................... 9 2.3 Boundary Detection Unit and Probe Mounting Device ............................................... 10 2.4 DATA Acquisition Electronics (DAE) and Measurement Server ............................... 10 2.5 Robot .............................................................................................11 2.6 Light Beam Unit........................................................................................................... 11 2.7 Device Holder ..............................................................................................................12 2.8 SAM Twin Phantom .................................................................................................... 12 3. Tissue Simulating Liquid .................................................................... 13 3.1 The composition of the tissue simulating liquid .......................................................... 13 3.2 Tissue Calibration Result ............................................................................................. 13 3.3 Tissue Dielectric Parameters for Head and Body Phantoms........................................ 14 4. SAR Measurement Procedure ............................................................ 15 4.1 SAR System Check ...................................................................................................... 15 4.1.1 Dipoles ...................................................................................................................... 15 4.1.2 System Check Result ................................................................................................ 15 4.2 SAR Measurement Procedure ...................................................................................... 16 4.2.1 SAR Measurement Procedure ................................................................................... 16 5. SAR Exposure Limits .......................................................................... 17 6. Test Equipment List ............................................................................ 18 7. Measurement Uncertainty................................................................... 19 8. Conducted Power Measurement ........................................................ 20 9. Duty cycle............................................................................................. 20 10 Test Results.......................................................................................... 21 10.1 SAR Test Results Summary ....................................................................................... 21 Report No：139135R-HPUSP10V01 Page: 4 of 23 11. SAR measurement variability ............................................................ 22 Appendix .............................................................................................23 Appendix A. SAR System Check Data Appendix B. SAR measurement Data Appendix C. Test Setup Photographs & EUT Photographs Appendix D. Probe Calibration Data Appendix E. Dipole Calibration Data Report No：139135R-HPUSP10V01 Page: 5 of 23 1. General Information 1.1 EUT Description Prod…

Text truncated - open the document above for the full version.

of Applicant: Coban Technologies, Inc Address: 11375 W. Sam Houston Parkway S. # 800 Houston Texas 77031 United States Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679A-1 A2LA Accredited No.: 2732.01 Report No.: W6M21304-13152-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for Wireless Microphone System Model No.: WMICG4-HU FCC ID: ZPJ-WMICG4-HU Registration number: W6M21304-13152-C-1 FCC ID: ZPJ-WMICG4-HU Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 39 TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................................2 1.1 N OTES.......................................................................................................................................................2 1.2 T ESTING LABORATORY............................................................................................................................3 1.2.1 Location ...............................................................................................................................................3 1.2.2 Details of accreditation status .............................................................................................................3 1.3 D ETAILS OF APPROVAL HOLDER..............................................................................................................3 1.4 A PPLICATION DETAILS.............................................................................................................................4 1.5 G ENERAL INFORMATION OF TEST ITEM...................................................................................................4 1.6 T EST STANDARDS.....................................................................................................................................5 2 TECHNICAL TEST .......................................................................................................................................6 2.1 S UMMARY OF TEST RESULTS....................................................................................................................6 2.2 T EST ENVIRONMENT................................................…

Text truncated - open the document above for the full version.