ZQAT30Wireless Device

Learning Thermostat ™ Installation Guide 064-00011-ES_16_InstallGuideENGLISH.indd 14/10/15 6:36 PM Compatibility Based on Nest’s online compatibility checker data, the Nest Thermostat works with most 24V systems, including gas, electric, oil, forced air, variable speed, heat pump, and radiant. It can control: • Heating: one, two, and three stages (W1, W2, W3) • Cooling: one and two stages (Y1, Y2) • Heat pump: with auxiliary and emergency heat (O/B, AUX, E) • Fan (G) • Power (C, RH, RC) • Humidifier or dehumidifier (HUM, DEHUM) The Nest Thermostat’s * connector can accept only one of these wires: W3, E, HUM or DEHUM. The Nest Thermostat is designed to work even if your home doesn’t have a common (C) wire. Rarely, installing a new C wire may be required. Professional installation recommended for: • Dual fuel systems (heat pump with furnace) • Whole-home humidifiers and dehumidifiers Watch the video To see how it’s done, watch our installation video at support.nest.com/thermostat WE TAKE YOUR PRIVACY SERIOUSLY We’re committed to being open and honest about how we use data. We’ll always ask for permission before sharing personally identifiable information like your email address, and we keep your data safe with industry standard security tools. To learn more about our Privacy Policy, go to nest.com/privacy 064-00011-ES_16_InstallGuideENGLISH.indd 2-34/10/15 6:36 PM Contents Display Optional steel plate screws Screwdriver Optional trim plate Base Optional steel plate Wall screws 1. Switch off power This protects you and avoids blowing a fuse in your equipment. Adjust the temperature on your old thermostat to make sure your system is off. 2. Remove cover Some covers pop off, while others need to be unscrewed. CAUTION: Do not connect Nest to high voltage wires. 4. Remove any jumper wires Jumper wires are short wires between two connectors. You won’t need them. An R wire can go into either RC or RH. 3. Check your system If your old thermostat is labeled 120V or 240V or has thick wires with wire nuts, your system is high voltage. Not sure? Contact support. Breaker box Switch 064-00011-ES_16_InstallGuideENGLISH.indd 4-54/10/15 6:36 PM Remember, the power to your HVAC system must be off to avoid blowing a fuse in your equipment. 6. Disconnect wires and remove base After removing the base, we recommend gently wrapping the wires around a pen or pencil to ensure they don’t fall back into the hole in the wall. 7. Mark where screws will go Use the bubble level to make sure the Nest Thermostat is level. 5. Label wires Peel off the labels below and attach them to the thermostat’s matching wires. Use the white labels for any W3, E, HUM or DEHUM wires. The * connector can only connect to one of these wires. See two names for each connector on your old thermostat’s backplate? Visit nest.com/2labels for help. Two labels Tip: Take a picture of the wires on your old thermostat to help you remember. Use trim plate if needed You can cover up holes or marks left by your old thermostat with the optional trim plate. Snap the base and trim plate together, then screw them to the wall. You’ll find the trim plate in the bottom of the box. Mounting on an electrical box Electrical boxes aren’t common, but if you have one, secure the steel plate to the electrical box with two of the short steel plate screws. Insert the screws into the long slots on the steel plate. Use the other two short screws to attach the Nest base and trim plate to the steel plate. Optional in most homes Optional in most homes 064-00011-ES_16_InstallGuideENGLISH.indd 6-74/10/15 6:36 PM Breaker box Switch 3/8 in The exposed wire should be straight. 8. Attach the Nest base Pull the wires through the center of the base, then attach it to the wall with the screws. 10. Attach the display Press the display onto the base until it clicks. 11. Switch the power back on 9. Connect wires After all the wires are securely connected, push them down to make sure they’re flush with the base. 12. Setup and Nest Account The Nest Thermostat will turn on and walk you through setup. Just turn the ring and press to select. During setup, you can connect the thermostat to Wi-Fi. Go to nest.com/account or download the Nest app to create a Nest Account. The app will show you how to connect your Nest Account and thermostat. Remember, you can download the free Nest app from the iTunes App Store ™ or Google Play ™ . Questions about adding a thermostat to your Nest Account? Visit nest.com/pair 064-00011-ES_16_InstallGuideENGLISH.indd 8-94/10/15 6:36 PM Nest Labs, Inc. Limited Warranty Learning Thermostat ™ THIS LIMITED WARRANTY CONTAINS IMPORTANT INFORMATION ABOUT YOUR RIGHTS AND OBLIGATIONS, AS WELL AS LIMITATIONS AND EXCLUSIONS THAT MAY APPLY TO YOU. 1. WHAT THIS LIMITED WARRANTY COVERS; PERIOD OF COVERAGE Nest Labs, Inc. (“Nest Labs”), 3400 Hillview Avenue, Palo Alto, California USA, warrants to the owner of the enclosed product that the product contained in this box (“Product”) will be free from defects in materials and workmanship for a period of two (2) years from the date of delivery following the original retail purchase (the “Warranty Period”). If the Product fails to conform to this Limited Warranty during the Warranty Period, Nest Labs will, at its sole discretion, either (a) repair or replace any defective Product or component; or (b) accept the return of the Product and refund the money actually paid by the original purchaser for the Product. Repair or replacement may be made with a new or refurbished product or components, at Nest Labs’ sole discretion. If the Product or a component incorporated within it is no longer available, Nest Labs may, at Nest Labs’ sole discretion, replace the Product with a similar product of similar function. This is your sole and exclusive remedy for breach of this Limited Warranty. Any Product that has either been repaired or replaced under this Limited Warranty will be covered by the terms of this Limited Warranty for the longer of (a) …

Text truncated - open the document above for the full version.

Page 1 of 4 Report No.: 150401C19 CONSTRUCTION PHOTOS OF EUT Page 2 of 4 Report No.: 150401C19 Page 3 of 4 Report No.: 150401C19 Page 4 of 4 Report No.: 150401C19

The label is located on the back of the device. FCC ID: ZQAT30 Model: A0013

Page 1 of 10 Report No.: 150401C19 CONSTRUCTION PHOTOS OF EUT Page 2 of 10 Report No.: 150401C19 Page 3 of 10 Report No.: 150401C19 Page 4 of 10 Report No.: 150401C19 Page 5 of 10 Report No.: 150401C19 Page 6 of 10 Report No.: 150401C19 Page 7 of 10 Report No.: 150401C19 Page 8 of 10 Report No.: 150401C19 Page 9 of 10 Report No.: 150401C19 Page 10 of 10 Report No.: 150401C19

FCC MPE Evaluation Report Report Format Version 5.0.0 Page No. : 1 of 8 Report No. : SA150401C19 R1 Issued Date : May 04, 2015 Cancels and replaces the report No.: SA150401C19 dated Apr. 22, 2015. FCC MPE Evaluation Report Report No. : SA150401C19 R1 Applicant : Nest Labs Inc. Address : 3400 Hillview Ave. Palo Alto California, United States 94304 Product : Wireless Device Model No. : A0013 Standards : FCC Part 2 (Section 2.1091) KDB 447498 D01 Sample Received Date : Apr. 01, 2015 Date of Evaluation : Apr. 20, 2015 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Gordon Lin / Assistant Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC MPE Evaluation Report Report Format Version 5.0.0 Page No. : 2 of 8 Report No. : SA150401C19 R1 Issued Date : May 04, 2015 Cancels and replaces the report No.: SA150401C19 dated Apr. 22, 2015. Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Description of Equipment Under Test ................................................................................................................................. 4 2. MPE (Maximum Permissible Exposure) Assessment ......................................................................................................... 5 2.1 Introduction .................................................................................................................................................................. 5 2.2 RF Radiation Exposure Limits ...................................................................................................................................... 5 2.3 MPE Assessment Method ............................................................................................................................................ 6 2.4 MPE Calculation for Standalone Operations ................................................................................................................ 6 2.5 MPE Calculation for Simultaneous Transmission Operations ...................................................................................... 7 3. Information on the Testing Laboratories ............................................................................................................................. 8 FCC MPE Evaluation Report Report Format Version 5.0.0 Page No. : 3 of 8 Report No. : SA150401C19 R1 Issued Date : May 04, 2015 Cancels and replaces the report No.: SA150401C19 dated Apr. 22, 2015. Release Control Record Report No. Reason for Change Date Issued SA150401C19 Initial release Apr. 22, 2015 SA150401C19 R1 Update model name May 04, 2015 FCC MPE Evaluation Report Report Format Version 5.0.0 Page No. : 4 of 8 Report No. : SA150401C19 R1 Issued Date : May 04, 2015 Cancels and replaces the report No.: SA150401C19 dated Apr. 22, 2015. 1. Description of Equipment Under Test EUT Type Wireless Device Model Name A0013 Tx Frequency Bands (Unit: MHz) WLAN : 2412 ~ 2462, 5180 ~ 5240, 5260 ~ 5320, 5500 ~ 5700, 5745 ~ 5825 Bluetooth : 2402 ~ 2480 15.4: 2405 ~ 2475 Uplink Modulations 802.11b : DSSS 802.11a/g/n : OFDM Bluetooth : GFSK 15.4: DSSS Antenna Type WLAN : Loop antenna Bluetooth : Chip antenna 15.4: Loop antenna Antenna Gain WLAN 2.4G: 1.1dBi gain WLAN 5G: 1.9dBi gain Bluetooth : -1.4dBi gain 15.4: -0.3dBi gain EUT Stage Identical Prototype Note: 1. The above EUT information is declared by manufacturer and for more detailed features description please refers to the manufacturer’s specifications or User’s Manual. FCC MPE Evaluation Report Report Format Version 5.0.0 Page No. : 5 of 8 Report No. : SA150401C19 R1 Issued Date : May 04, 2015 Cancels and replaces the report No.: SA150401C19 dated Apr. 22, 2015. 2. MPE (Maximum Permissible Exposure) Assessment 2.1 Introduction According to 47 CFR §2.1091, a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained betwe…

Text truncated - open the document above for the full version.

Report No.: RF150401C19 R1 1 of 41 Report Format Version 5.1.0 Cancels and replaces the report No.: RF150401C19 dated Apr. 22, 2015. FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF150401C19 R1 MODEL NO.: A0013 FCC ID: ZQAT30 RECEIVED: Apr. 01, 2015 TESTED: Mar. 27, 2015 ~ May 09, 2015 ISSUED: May 11, 2015 APPLICANT: Nest Labs Inc. ADDRESS: 3400 Hillview Ave. Palo Alto California, United States 94304 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150401C19 R1 2 of 41 Report Format Version 5.1.0 Cancels and replaces the report No.: RF150401C19 dated Apr. 22, 2015. TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................. 4 1. CERTIFICATION ................................................................................................................................. 5 2. SUMMARY OF TEST RESULTS ........................................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................................. 6 3. GENERAL INFORMATION ................................................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................ 9 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 10 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.4 DUTY CYCLE TEST SIGNAL ................................................................................................... 13 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 13 4. TEST TYPES AND RESULTS (FOR BLUETOOTH LE 4.0) ............................................................. 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 14 4.1.2 TEST INSTRUMENTS ................................................................................................. 15 4.1.3 TEST PROCEDURES ................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 16 4.1.5 TEST SETUP ............................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 17 4.1.7 TEST RESULTS........................................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 24 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 24 4.2.2 T EST INSTRUMENTS ................................................................................................ 24 4.2.3 TEST PROCEDURES ................................................................................................. 25 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 25 4.2.5 TEST SETUP ............................................................................................................... 25 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 25 4.2.7 TEST RESULTS........................................................................................................... 26 4.3 6dB BANDWIDTH MEASUREMENT ....................................................................................... 30 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................................ 30 4.3.2 TEST SETUP ...................................................................…

Text truncated - open the document above for the full version.

Report No.: RF150401C19-1 R1 1 of 55 Report Format Version 5.2.1 Cancels and replaces the report No.: RF150401C19-1 dated Apr. 22, 2015. FCC TEST REPORT (15.247) REPORT NO.: RF150401C19-1 R1 MODEL NO.: A0013 FCC ID: ZQAT30 RECEIVED: Apr. 01, 2015 TESTED: Apr. 07, 2015 ~ May 09, 2015 ISSUED: May 11, 2015 APPLICANT: Nest Labs Inc. ADDRESS: 3400 Hillview Ave. Palo Alto California, United States 94304 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150401C19-1 R1 2 of 55 Report Format Version 5.2.1 Cancels and replaces the report No.: RF150401C19-1 dated Apr. 22, 2015. TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................. 4 1. CERTIFICATION ................................................................................................................................. 5 2. SUMMARY OF TEST RESULTS ........................................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................................. 6 3. GENERAL INFORMATION ................................................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................ 9 3.3 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................... 12 3.4 DUTY CYCLE TEST SIGNAL ................................................................................................... 14 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 14 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ....................................................................... 15 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 15 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 15 4.1.2 TEST INSTRUMENTS ................................................................................................. 16 4.1.3 TEST PROCEDURES ................................................................................................. 17 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 17 4.1.5 TEST SETUP ............................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 18 4.1.7 TEST RESULTS........................................................................................................... 19 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 31 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 31 4.2.2 TEST INSTRUMENTS ................................................................................................. 31 4.2.3 TEST PROCEDURES ................................................................................................. 32 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 32 4.2.5 TEST SETUP ............................................................................................................... 33 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 33 4.2.7 TEST RESULTS........................................................................................................... 34 4.3 6dB BANDWIDTH MEASUREMENT ....................................................................................... 38 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................................ 38 4.3.2 TEST SETUP .......................................................…

Text truncated - open the document above for the full version.

Report No.: RF150401C19-3 R1 1 of 42 Report Format Version 5.2.1 Cancels and replaces the report No.: RF150401C19-3 dated Apr. 22, 2015. FCC TEST REPORT (15.247_15.4) REPORT NO.: RF150401C19-3 R1 MODEL NO.: A0013 FCC ID: ZQAT30 RECEIVED: Apr. 01, 2015 TESTED: Mar. 30, 2015 ~ May 09, 2015 ISSUED: May 11, 2015 APPLICANT: Nest Labs Inc. ADDRESS: 3400 Hillview Ave. Palo Alto California, United States 94304 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150401C19-3 R1 2 of 42 Report Format Version 5.2.1 Cancels and replaces the report No.: RF150401C19-3 dated Apr. 22, 2015. TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 4 1. CERTIFICATION ............................................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ..................................................................... 6 3. GENERAL INFORMATION ............................................................................................................ 7 3.1 GENERAL DESCRIPTION OF EUT .................................................................. 7 3.2 DESCRIPTION OF TEST MODES .................................................................... 7 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................. 8 3.3 DUTY CYCLE OF TEST SIGNAL .................................................................... 10 3.4 DESCRIPTION OF SUPPORT UNITS ............................................................ 10 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 13 4. TEST TYPES AND RESULTS ..................................................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .......................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................... 14 4.1.2 TEST INSTRUMENTS .................................................................................................. 15 4.1.3 TEST PROCEDURES ................................................................................................... 16 4.1.4 DEVIATION FROM TEST STANDARD ......................................................................... 17 4.1.5 TEST SETUP ................................................................................................................ 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................. 18 4.1.7 TEST RESULTS ............................................................................................................ 19 4.2 CONDUCTED EMISSION MEASUREMENT .................................................. 25 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................................. 25 4.2.2 TEST INSTRUMENTS .................................................................................................. 25 4.2.3 TEST PROCEDURES ................................................................................................... 26 4.2.4 DEVIATION FROM TEST STANDARD ......................................................................... 26 4.2.5 TEST SETUP ................................................................................................................ 26 4.2.6 EUT OPERATING CONDITIONS .........................................................................…

Text truncated - open the document above for the full version.