ZSYJXD76499973Remote Control Flying Saucer

User Manual Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment such modifications could void the user authority to operate the equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Block Diagram BK 2423 2.4GHz Radio Chip Oscillator Y1 16MHz Encoder CPU Ant Control key IC1 N79E815A20 IC2 Power Amplifier 2417MHz~2458MHz

FCC ID: ZSYJXD76499973 External Photo FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973

FCC ID: ZSYJXD76499973 Internal Photo FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973

Operation Description: This device is the controller of the 2.4GHz remote control helicopter. The controller is operating from 2417MHz - 2458MHz and powered by DC 9V (six AA batteries). When the Controller is switch on, the remote controller will transmit a RF signal on the channel which is pre-selected during factory aligned with the receiver within 2417 – 2548MHz to control the helicopter. When the receiver is receiving the RF signal under the aligned channel, the receiver will control the four blades to move the helicopter The pre-selected channels of the device are 2417MHz, 2421MHz, 2425MHz, 2429MHz, 2432MHz, 2437MHz, 2441MHz, 2445MHz, 2449MHz, 2453MHz, 2458MHz. The device has two control levers to control moving forward backward and turn around respectively. The control signals from the two levers are encoded by IC, N79E815A20 and send the code to the 2.4 GHz RF modules L0G2425. About RF module L0G2425, The main IC chip IC1 BK2423 cooperated with 16MHz oscillator, which will transmit RF channels within the frequency range from 2417MHz~2458MHz with GFSK modulation, and pass through RF filter (C10, L3 & C19) to amplifier, IC2, RFX2402C to amplifier the signal to TX antenna.

123456 A B C D 654321 D C B A 标题 图号修订尺寸 B 日期:5-Sep-2013 第 张 共 张 文件:F:\LG.DDB制图人: CE 1 CSN 2 SCK 3 MOSI 4 MISO 5 IRQ 6 VDD 7 V SS 8 X T A LP 9 X T A LN 10 VDDPA 11 RFP 12 RFN 13 VSS 14 VDD 15 IREF 16 V SS 17 VDD 18 C DVDD 19 V SS 20 IC1 BK2423 C1 10UF C3 820NF R1 0R R3 22K R13 1M CE CSN SCK MOSI MISO IRQ L1 6.8NH L4 33nH L2 4.7nH L5 10NH C16 36P C17 36P Y1 16MHz C10 2.2P C18 4.7P C7 2.2P C8 NC C6 33NF E1 ANTENNA RX 1 GND 2 GND 3 4 TXEN 5 RXEN 6 DET 7 GND 8 9 10 GND 11 GND 12 DNC 13 VCCPA 14 GND 15 VCCLNA 16 C15 IC2 R6 0R R4 NC R10 10K R8 1K R7 1K R5 0R R2 0R R9 0R R12 0R R11 0R C19 1.2P C2 10UF C14 1p C12 4p C4 220P C9 NC C5 220P C13 1p C11 NC L3 4.7nH 3.3V 3.3V RXEN R3 10K PDF pdfFactory www.fineprint.cn GND GND OUT IN 1 2 3 4 LH1 BF2520 GND ANT TX DEZIGN: CHECKED: APPROVED: MODEL NO: MODEL NAME: PCB NO: DRAWING NO: REV: CODE: SIZE: SHEET: VDD /*;7; C2103 C5103 C3103C6103








 VDD
    4 5 6 1 2 3 7 8 9 J1 CON9A 2.4G_SO 2.4G_SCLK 2.4G_SI 2.4G_CSN R31K D1LED LV  RW1POT2-2 RW2POT2-2 S7MUNE S11CH4- S6DOWN S8CH3- S2CH1+ S3CH1- S10CH4+ S9CH3+ S4CH2+ S5CH2- VDD CH1CH2 R16 1K R17 1K R15 1K R13 1K R14 1K VDD R23 1K R18 1K R22 1K R20 1K R21 1K R1968KR2668K C14103C13103 CH1 CH2 /CS VDD R110 C1104 4561237 J2 CON7A /CS R4 2.2K VCC+ R2100R LED3 DATA VDD R7 2.2K R5 2.2K VDD 45123 J3CON5 R6 100K C4104 ISP_VPP CLK VDD ISP_DTA ISP_CLK U1 BUZZER BUZZ R92.2K VCC+ BUZZ 2.4G_SO 2.4G_SCLK 2.4G_SI 2.4G_CSN ISP_VPPISP_DTAISP_CLK CLKDATA Q28050 R8 100R VDD2 Q1 8050 PA2/AD2/BZ1 PA3/AD3/PWM1 RTCC/AD4 RESB/PA5 VSS PC0/AD5 PB0/INT PB7 PB6 PB5PB4 PB3/PWM2 PB2/BZ2 PB1/IR VREF VDD PA7/XOUT PA6/XIN PA0AD0 PA1/AD1 IC1N79E815A20 S12CH5+ R24 1K R251K S13CH5- LED4 LED3 LED4 AD0 C8104 VDD GND IN OUT IC46204 VDD2 C11 475 C12104 C7475 C10100U CHRGGNDBAT VCC PROG IC2 6204 BT1 S1 VCC+7.4V GND IN OUT IC3 1117 R1110 C9100U VCC R1210KR1022K 

Report No.: HKEM131000024601 Page: 1 of 20 Authorized Signature: LOKE Sai Kit, Wilson Senior Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS IECC Limited or testing done by SGS IECC Limited in connection with, distribution or use of the product described in this report must be approved by SGS IECC Limited in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. FCC ID: ZSYJXD76499973 Member of the SGS Group (SGS SA) FCC Test Report Application No.: HKES13100024601 Applicant: SHANTOU CHENGHAI JIN XING DA PLASTIC TOYS FACTORY Address: Linghai Industrial Area, Batou, Chenghai District Shantou City China Product Information: Product Description: Remote Control Flying Saucer Model No.(EUT): JD385, 335, 339, 349, 351, 356, 352W, 365, 366, 380, 381, 382, 383, 386, 387, 388, 389, 390, 391, 392, 393, 395, 396, 397, 398, 399 ♣ ♣ Please refer to section 2 of this report which indicates which item was actually tested and which were electrically identical. Product Class : Low Power Communication Device – Transmitter (2.4 GHz) FCC ID: ZSYJXD76499973 Requirement: CFR 47 FCC PART 15 SUBPART C, 2012 - Intentional Radiators. Date of Receipt: 2013-10-22 Date of Test: 2013-11-01 Date of Issue: 2013-11-04 Test Result : PASS* * In the configuration tested, the EUT complied with the requirements for the relevant clauses of Federal Communications Commission Rules as specified above. Report No.: HKEM131000024601 Page: 2 of 20 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. FCC ID: ZSYJXD76499973 Member of the SGS Group (SGS SA) 2 Test Summary Test Test Requirement Test Method Result Conducted Emission (150KHz to 30MHz) FCC PART 15, SUBPART C: 2012 ANSI C63.4:2003 N/A 1) Radiated Emission (9kMHz to 1GHz) FCC PART 15, SUBPART C: 2012 ANSI C63.4:2003 PASS Radiated Emission above 1 GHz FCC PART 15, SUBPART C: 2012 ANSI C63.4:2003 PASS Band edge / 20 dB Bandwidth FCC PART 15, SUBPART C: 2012 ANSI C63.4:2003 Marker-Detla measurement PASS Remark : 1) Please refer to section 6.1 of this report for explanation Item no.: JD385, 335, 339, 349, 351, 356, 352W, 365, 366, 380, 381, 382, 383, 386, 387, 388, 389, 390, 391, 392, 393, 395, 396, 397, 398, 399 According to the confirmation from the applicant, the above models are identical in all electrical aspects in relating to the circuit design, PCB layout, electrical components used, internal wiring and function. The differences are only the model and color. Therefore only the model JD385 was tested in this report. Report No.: HKEM131000024601 Page: 3 of 20 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This do…

Text truncated - open the document above for the full version.

FCC ID: ZSYJXD76499973 Setup Photo Radiated emission FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973 FCC ID: ZSYJXD76499973