ZY9-D14USmart Speaker

110X110mm，封面封底105克铜版纸彩色印刷，内页80克书写纸彩色印刷 2020-06-03 D14U D14U D14U D14U D14U D14U The warning triangle with exclamation mark indicates important operating and maintenance instructions Warning! This device is designed for use below 2000 metres in altitude. Warning! This product is not intended for use in tropical climates. Safety information 2 3 5 5 6 8 15 17 19 21 22 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body. Safety information Œ Google LED indicator  Next track/ Volume up: click one time to increase volume one level. Double click for next song. Long press to continue increasing volume. Ž Play/Pause button: Press for Play/ Pause.  Bluetooth button: Press for Bluetooth input. At Bluetooth input: Long press 3s for Bluetooth pairing mode  Mic holes:Two Mic located at the left and right side on the top. ‘ Previous track/ Volume down: Click one time to decrease volume one level. Double click for last song. Long press to continue decreasing volume. D14U Speaker Quick Start Guide 3 ’ Function mode indicator WiFi stage: a. WiFi connected > light keep lighting b. WiFi disconnected > the LED flashing (1 time/ 3s) Bluetooth mode: a. At connected mode > light keep lighting b. At pairing mode > the LED flashing (1 time/ 3s) BT stage: a. BT paired > light keep lighting b. BT not paired > sparkling (1 time/ 3s) “ Mute button: Short press for Mute or Un-Mute the Mic (4 system LEDs change to orange in mute mode.) ” DC Power Cable: DC12V, 2.0A max • Software upgrade port l Long press both VOL- and VOL+ buttons for 10s to trigger FDR. l Power on: Connect power cable for power on > Google LED light from left to right (blue, red, orange, green) for around 60s > can hear the warning tone of “Ding” (that means system Initialization completed). D14U Speaker Quick Start Guide 4 1. Download Google Home App (download at App store or Android appliance store) 2. Open Google Home App. Register an account and login 3. Device adding 4. Add device after login. Meantime, please change the device name to user wants. For example “Philips light” Before using D14U AI speaker, please make sure to meet below conditions: a, Access Google Play Store on your phone or your smart device. b, Download the Google Home App. 5 Add D14U speaker at Google Home App 6 Create D14U room 7 Add D14U speaker at Google Home App 1. Plug the power adapter > device open automatically > 4 LED lights color change to blue, red, yellow, green from left to right > device gets into system initialization > after around 30s > can hear the voice of “Ding” (that means the device name can be found at Bluetooth). 2 Make sure that the D14U environment has a WiFi network with smooth access to Google service before Mobile/ iPad can connect with WiFi. Configuring D14U with Home App 8 Configuring D14U with Home App Starting Configuring D14U with Google Home App 9 Configuring D14U with Home App Starting Configuring D14U with Google Home App Choose D14U ... NEXT 10 Configuring D14U with Home App Starting Configuring D14U with Google Home App 11 Configuring D14U with Home App Starting Configuring D14U with Google Home App 12 Configuring D14U with Home App Starting Configuring D14U with Google Home App 13 Configuring D14U with Home App Starting Configuring D14U with Google Home App 14 Give some instructions to D14U speaker Give some instructions to D14U speaker, it will give some feedback Steps: To wake up D14U > speak “OK GOOGLE” > 4 white LED color sparking ( it means D14U speaker is waken up ) Give some instruction as below: “ Hello! ” “ What time is it? ” “ Set alarm time at 6:00pm today. ” “ Play KBS radio. ” Bluetooth connection: Turn on the Bluetooth and find the device with the name of “back garden” (name will be changed per the name that user named). Once paired successfully, you can play music at D14U speaker. 15 Give some instructions to D14U speaker Give some instructions to D14U speaker, it will give some feedback 16 17 18 19 Typing D14U speaker ... Save 20 1. Smart home appliance (eg. Air conditioning), login with the same Google account as D14U speaker. 2. Enable skill, Link ID. 3. Smart home appliance control. D14U setting for the Internet of Things D14U 21 Standard testing environment: 1. Put D14U speaker at appointed testing place 2 .The voice position for waking up with “OK Google” and play music. Refer to female voice pronuncation. Male’s bass pronunciatio…

Text truncated - open the document above for the full version.

TRFNO.FCC15/APage1of4ReportNo.:ES191115017WVer.1.0 EUTEXTERNALPHOTOGRAPHS TRFNO.FCC15/APage2of4ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage3of4ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage4of4ReportNo.:ES191115017WVer.1.0 ----------------Theend----------------

7 1 . 8 74.3 音箱菲林图 D14U Made in China 3 1 4 4 4 8 0

TRFNO.FCC15/APage1of8ReportNo.:ES191115017WVer.1.0 EUTINTERNALPHOTOGRAPHS TRFNO.FCC15/APage2of8ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage3of8ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage4of8ReportNo.:ES191115017WVer.1.0 Antenna TRFNO.FCC15/APage5of8ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage6of8ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage7of8ReportNo.:ES191115017WVer.1.0 TRFNO.FCC15/APage8of8ReportNo.:ES191115017WVer.1.0 ----------------Theend----------------

FCCID:ZY9-D14U RFEXPOSUREEVALUATION AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeusedtoevaluatetheenvironmentimpactofhumanexposuretoradiofrequency(RF)Radiationasspecifiedin§1.1307(b) LimitsforMaximumPermissibleExposure(MPE) Frequency Range(MHz) ElectricField Strength(V/m) MagneticField Strength(A/m) Power Density(mW/cm 2 ) AverageTime (A)LimitsforOccupational/ControlExposures 300-1500----F/3006 1500-100000----56 (B)LimitsforGeneralPopulation/UncontrolExposures 300-1500----F/15006 1500-100000----130 11.1Friistransmissionformula:Pd=(Pout*G)\(4*pi*R 2 ) Where Pd=PowerdensityinmW/cm 2 Pout=outputpowertoantennainmW G=Numericgainoftheantennarelativetoisotropicantenna Pi=3.1416 R=distancebetweenobservationpointandcenteroftheradiatorin20cm PdthelimitofMPE,1mW/cm 2 .Ifweknowthemaximumgainofthendtotalpowerinputtotheantenna,throughthecalculation,wewillknowthedistancewheretheMPElimitisreached. 11.2MeasurementResult WIFI5G: WIFI2.4G: modulation conductedpower (mW) conducted power (dBm) Tune-uppower(dBm) Max tune-up power (dBm) Max tune-up power (mW) Antenna Gain Numeric Evaluation result (mW/cm2) Powerdensity Limits (mW/cm2) 11b63.1017.1616dBmto18dBm1863.1020.0251<1 11g50.1215.6715dBmto17dBm1750.1220.0199<1 11nHT2031.6214.2413dBmto15dBm1531.6220.0126<1 11nHT4025.1213.2512dBmto14dBm1425.1220.0100<1 BTDSS modulation conducted power (mW) conducted power (dBm) Tune-uppower(dBm) Max tune-up power (dBm) Max tune-up power (mW) Antenna Gain Numeric Evaluation result (mW/cm2) Powerdensity Limits (mW/cm2) GFSK5.015.595dBmto7dBm75.0120.0020<1 pi/4-DQPSK6.316.26dBmto8dBm86.3120.0025<1 8DPSK6.316.616dBmto8dBm86.3120.0025<1 BTDTS Channel Freq. (MHz) modulation conducted power (mW) conducted power (dBm) Tune-uppower(dBm) Max tune-up power (dBm) Max tune-up power (mW) Antenna Gain Numeric Evaluation result (mW/cm2) Powerdensity Limits (mW/cm2) 2402GFSK3.163.753dBmto5dBm53.1620.0013<1 2440GFSK3.163.403dBmto5dBm53.1620.0013<1 2480GFSK2.512.142dBmto4dBm42.5120.0010<1 WIFI5G+WIFI2.4G+BTMAXRFEXPOSUREEVALUATION MaxWIFI2.4Gband Evaluationresult (mW/cm2) MaxWIFI5Gband Evaluationresult (mW/cm2) MaxBTEvaluation result (mW/cm2) Summationof Evaluationresult (mW/cm2) PowerdensityLimits (mW/cm2) 0.01990.02510.00250.0475<1 modulation conducted power (mW) conducted power (dBm) Tune-uppower(dBm) Max tune-up power (dBm) Max tune-up power (mW) Antenna Gain Numeric Evaluation result (mW/cm2) Powerdensity Limits (mW/cm2) 11a50.1215.3115dBmto17dBm1750.1220.0199<1 11n(VHT20)50.1215.2515dBmto17dBm1750.1220.0199<1 11ac(VHT20)39.8114.0914dBmto16dBm1639.8120.0158<1 11n(VHT40)31.6213.3513dBmto15dBm1531.6220.0126<1 11ac(VHT40)31.6213.5013dBmto15dBm1531.6220.0126<1 11ac(VHT80)25.1212.3712dBmto14dBm1425.1220.0100<1

RReportNo.ES200117042W04Page1of169Ver.1.0 TEST REPORT Product Name：Smart Speaker Model Number：D14U FCC ID：ZY9-D14U Prepared for:Shenzhen Great Power Innovation and Technology Enterprise Co.,Ltd Address:Building E, Xin Xulong Industrial Area, Kukeng Village, Guanlan Town, Longhua New District, Shenzhen, China Prepared by:EMTEK (SHENZHEN) CO., LTD. Address:Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26954280 Fax: (0755) 26954282 Report Number:ES200117042W04 Date(s) of Tests:January 18, 2020 to April 16, 2020 Date of issue:May 6, 2020 $二维码$ RReportNo.ES200117042W04Page2of169Ver.1.0 1 TEST RESULT CERTIFICATION Applicant:Shenzhen Great Power Innovation and Technology Enterprise Co.,Ltd Address: Building E, Xin Xulong Industrial Area, Kukeng Village, Guanlan Town, Longhua New District, Shenzhen, China Manufacturer:Shenzhen Great Power Innovation and Technology Enterprise Co.,Ltd Address： Building E, Xin Xulong Industrial Area, Kukeng Village, Guanlan Town, Longhua New District, Shenzhen, China EUT:Smart Speaker Model Name:D14U Trademark:KONKA Measurement Procedure Used: APPLICABLE STANDARDS STANDARDTEST RESULT FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart E PASS The above equipment was tested by EMTEK (SHENZHEN) CO., LTD. The test data,data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sampleEUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.407 The test results of this report relate only to the tested sample identifiedin this report. Date of Test :January 18, 2020 to April 16, 2020 Prepared by : Mill Chen /Editor Reviewer : Sewen Guo /Supervisor Approve & Authorized Signer : Lisa Wang/Manager RReportNo.ES200117042W04Page3of169Ver.1.0 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION.............................................................................................................................2 2 EUT TECHNICAL DESCRIPTION............................................................................................................................4 3 SUMMARY OF TEST RESULT..................................................................................................................................6 4 TEST METHODOLOGY..............................................................................................................................................7 4.1 GENERAL DESCRIPTION OF APPLIED STANDARDS.....................................................................................7 4.2 MEASUREMENT EQUIPMENT USED.................................................................................................................7 4.3 DESCRIPTION OF TEST MODES.........................................................................................................................8 5 FACILITIES AND ACCREDITATIONS..................................................................................................................12 5.1 FACILITIES............................................................................................................................................................12 5.2 LABORATORY ACCREDITATIONS AND LISTINGS......................................................................................12 6 TEST SYSTEM UNCERTAINTY..............................................................................................................................13 7 SETUP OF EQUIPMENT UNDER TEST.................................................................................................................14 7.1 RADIO FREQUENCY TEST SETUP....................................................................................................................14 7.2 RADIO FREQUENCY TEST SETUP....................................................................................................................14 7.3 CONDUCTED EMISSION TEST SETUP.............................................................................................................16 7.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM............................................................................17 7.5 SUPPORT EQUIPMENT.......................................................................................................................................17 8 TEST REQUIREMENTS............................................................................................................................................18 8.1 BANDWIDTH MEASUREMENT.........................................................................................................................18 8.2 MAXIMUM CONDUCTED OUTPUT POWER...................................................................................................87 8.3 MAXIMUM PEAK POWER DENSITY................................................................................................................93 8.4 FREQUENCY STABILITY.................................................................................................................................127 8.5 UNDESIRABLE RADIATED SPURIOUS EMISSION......................................................................................136 8.6 POWER LINE CONDUCTED EMISSIONS.......................................................................................................165 8.7 ANTENNA APPLICATION................................................................................................................................ 168 RReportNo.ES200117042W04Page4of169Ver.1.0 2 EUT TECHNICAL DESCRIPTION CharacteristicsDescription ProductSmart Speaker Model NumberD14U Wifi Type UNII-1: 5150MHz-5250MHz Band UNII-2A: with 5250MHz-5350MHz Band UNII-2C: with 5470MHz-5725MHz Band UNII-3 with 5725MHz-5850MHz Band WLAN Supported 802.11a 802.11n(20MHz channel bandwidth) 802.11n(40MHz channel bandwidt…

Text truncated - open the document above for the full version.

RReportNo.ES200117042W04Page153of169Ver.1.0 Test Model U-NII -2C Undesirable radiated Spurious Emission in Restricted Band (5350-5400MHz) 802.11a802.11n(HT20)802.11 ac (VHT20) 550055805700Ant.PolH Test Model U-NII -2C Undesirable radiated Spurious Emission in Restricted Band (5350-5400MHz) 802.11a802.11n(HT20)802.11 ac (VHT20) 550055805700Ant.PolV RReportNo.ES200117042W04Page154of169Ver.1.0 For Undesirable radiated Spurious Emission in U-NII -3 All the modes 802.11a/n/ac has been tested and the worst result 802.11a recorded as below:  Undesirable radiated Spurious Emission Above 1GHz (1GHz to 40GHz) Test mode:802.11aFrequency(MHz):5745 Freq. (MHz) Ant.Pol. Field Strength (dBuV/m) E.I.R.P (dBm) Limit (dBm)Over(dB) H/V 3924.85V46.19-49.13-27-22.13 11413.35V56.96-38.36-27-11.36 17739.05V60.3-35.02-27-8.02 3897.65H44.83-50.49-27-23.49 11598.65H56.51-38.81-27-11.81 17773.05H60.12-35.2-27-8.2 Test mode:802.11aFrequency(MHz):5785 Freq. (MHz) Ant.Pol. Field Strength (dBuV/m) E.I.R.P (dBm) Limit (dBm)Over(dB) H/V 3924.85V45.19-50.13-27-23.13 11994.75V57.09-38.23-27-11.23 17739.05V59.3-36.02-27-9.02 3788.85H45.62-49.7-27-22.7 12172.4H57.21-38.11-27-11.11 17773.05H59.62-35.7-27-8.7 Test mode:802.11aFrequency(MHz):5825 Freq. (MHz) Ant.Pol. Field Strength (dBuV/m) E.I.R.P (dBm) Limit (dBm)Over(dB) H/V 3924.85V46.19-49.13-27-22.13 11413.35V56.96-38.36-27-11.36 17739.05V59.8-35.52-27-8.52 3806.7H45.49-49.83-27-22.83 12384.05H57.37-37.95-27-10.95 17938.8H59.86-35.46-27-8.46 Note:(1) All Readings are Peak Value (VBW=3MHz) and AV Value (VBW=10Hz). (2) Emission Level= Reading Level+Probe Factor +Cable Loss. (3)EIRP[dBm] = E[dBμV/m] + 20 log(d[meters]) - 104.77 d is the measurement distance in 3 meters (4)The reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. RReportNo.ES200117042W04Page155of169Ver.1.0 Frequency:802.11aFrequency(MHz):5745 Freq. (MHz) Ant.Pol. Emission Level(dBuV/m) Limit 3m(dBuV/m)Margin (dB) H/VPKAVPKAVPKAV 3924.85V46.1933.297454-27.81-20.71 11413.35V56.9642.267454-17.04-11.74 17739.05V60.3044.757454-13.70-9.25 3897.65H44.8331.567454-29.17-22.44 11598.65H56.5142.087454-17.49-11.92 17773.05H60.1244.477454-13.88-9.53 Frequency:802.11aFrequency(MHz):5785 Freq. (MHz) Ant.Pol. Emission Level(dBuV/m) Limit 3m(dBuV/m)Margin (dB) H/VPKAVPKAVPKAV 3924.85V45.1932.517454-28.81-21.49 11994.75V57.0941.527454-16.91-12.48 17739.05V59.3045.067454-14.70-8.94 3788.85H45.6232.047454-28.38-21.96 12172.4H57.2142.227454-16.79-11.78 17773.05H59.6244.267454-14.38-9.74 Frequency:802.11aFrequency(MHz):5825 Freq. (MHz) Ant.Pol. Emission Level(dBuV/m) Limit 3m(dBuV/m)Margin (dB) H/VPKAVPKAVPKAV 3924.85V46.1933.227454-27.81-20.78 11413.35V56.9641.297454-17.04-12.71 17739.05V59.8044.557454-14.20-9.45 3806.7H45.4932.427454-28.51-21.58 12384.05H57.3741.247454-16.63-12.76 17938.8H59.8645.057454-14.14-8.95 Note:(1) All Readings are Peak Value (VBW=3MHz) and Peak Value (VBW=10Hz). (2) Emission Level= Reading Level+Correct Factor +Cable Loss. (3) Correct Factor= Ant_F + Cab_L - Preamp (4)The reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. RReportNo.ES200117042W04Page156of169Ver.1.0 Undesirable radiated Spurious Emission in band edge Test mode:802.11aFrequency:5745 Freq. (MHz) Ant.Pol. Field Strength (RBW=100KHz) (dBuV/m) E.I.R.P (dBm) Limit (dBm) Verdict H/V 5723.350H66.09-29.2326.31PASS 5723.163V65.89-29.4329.87PASS Test mode:802.11aFrequency:5825 Freq. (MHz) Ant.Pol. Field Strength (RBW=100KHz) (dBuV/m) E.I.R.P (dBm) Limit (dBm) Verdict H/V 5850.813H60.15-35.1727.57PASS 5850.163V59.71-35.6128.47PASS Note:(1) All Readings are Peak Value (VBW=3MHz) and Peak Value (VBW=10Hz). (2) Emission Level= Reading Level+Correct Factor +Cable Loss. (3) Correct Factor= Ant_F + Cab_L - Preamp (4) EIRP[dBm] = E[dBμV/m] + 20 log(d[meters]) - 104.77 d is the measurement distance in 3 meters RReportNo.ES200117042W04Page157of169Ver.1.0 Test Model U-NII -3 Undesirable radiated Undesirable radiated Spurious Emission in Band Edge 802.11a802.11n(HT20)802.11n(HT40) 5745Ant.PolH Test Model U-NII -3 Undesirable radiated Undesirable radiated Spurious Emission in Band Edge 802.11a802.11n(HT20)802.11n(HT40) 5745Ant.PolV RReportNo.ES200117042W04Page158of169Ver.1.0 Test Model U-NII -3 Undesirable radiated Undesirable radiated Spurious Emission in Band Edge 802.11a802.11n(HT20)802.11n(HT40) 5825Ant.PolH Test Model U-NII -3 Undesirable radiated Undesirable radiated Spurious Emission in Band Edge 802.11a802.11n(HT20)802.11n(HT40) 5825Ant.PolV RReportNo.ES200117042W04Page159of169Ver.1.0 Undesirable radiated Spurious Emission below 1GHz (30MHz to 1GHz) All the modes 802.11a/n/ac has been tested and the worst result 802.11a recorded as below: RReportNo.ES200117042W04Page160of169Ver.1.0 RReportNo.ES200117042W04Page161of169Ver.1.0 RReportNo.ES200117042W04Page162of169Ver.1.0 RReportNo.ES200117042W04Page163of169Ver.1.0 RReportNo.ES200117042W04Page164of169Ver.1.0 RReportNo.ES200117042W04Page165of169Ver.1.0 8.6 POWER LINE CONDUCTED EMISSIONS 8.6.1 Applicable Standard According to FCC Part 15.207(a) 8.6.2 Conformance Limit Conducted Emission Limit Frequency(MHz)Quasi-peakAverage 0.15-0.566-5656-46 0.5-5.05646 5.0-30.06050 Note: 1. The lower limit shall apply at the transition frequencies 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 8.6.3 Test Configuration Test according to clause 6.3 conducted emission test setup 8.6.4 Test Procedure The EUT was placed on a table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Repeat above procedures until all frequency measured were complete. 8.6.5 Test Results Pass The 120V &240V voltagehave been tested, and the worst result recorded was report as below: RReportNo.ES200117042W04Page166of169Ver.1.0 RReportNo.ES200117042W04Page167of169Ver.1.0 RRepor…

Text truncated - open the document above for the full version.

ReportNo.ES200117042W05Page1of23Ver.1.0 TESTREPORT ProductName：SmartSpeaker ModelNumber：D14U FCCID：ZY9-D14U Preparedfor:ShenzhenGreatPowerInnovationandTechnologyEnterpriseCo.,Ltd Address:BuildingE,XinXulongIndustrialArea,KukengVillage,Guanlan Town,LonghuaNewDistrict,Shenzhen,China Preparedby:EMTEK(SHENZHEN)CO.,LTD. Address:Bldg69,MajialongIndustryZone,NanshanDistrict,Shenzhen, Guangdong,China Tel:(0755)26954280 Fax:(0755)26954282 ReportNumber:ES200117042W05 Date(s)ofTests:January18,2020toApril16,2020 Dateofissue:May6,2020 $二维码$ ReportNo.ES200117042W05Page2of23Ver.1.0 TABLEOFCONTENTS 1.TESTRESULTCERTIFICATION ......................................................................................... 3 2.EUTDESCRIPTION ................................................................................................................ 4 3.SUMMARYOFTESTRESULT ............................................................................................. 5 4.TESTMETHODOLOGY .......................................................................................................... 6 4.1GENERALDESCRIPTIONOFAPPLIEDSTANDARDS ................................................................ 6 4.2MEASUREMENTEQUIPMENTUSED ........................................................................................ 6 4.3DESCRIPTIONOFTESTMODES ............................................................................................. 7 5.FACILITIESANDACCREDITATIONS ................................................................................ 9 5.1FACILITIES .............................................................................................................................. 9 5.2EQUIPMENT ............................................................................................................................ 9 5.3LABORATORYACCREDITATIONSANDLISTINGS .................................................................... 9 6.SETUPOFEQUIPMENTUNDERTEST ........................................................................... 10 6.1SETUPCONFIGURATIONOFEUT ......................................................................................... 10 6.2CALIBRATIONOFDFSDETECTIONTHRESHOLDLEVEL: .................................. 10 6.3SUPPORTEQUIPMENT ......................................................................................................... 11 7.DYNAMICFREQUENCYSELECTIONREQUIREMENTS ............................................ 12 7.1APPLICABLESTANDARD ...................................................................................................... 12 7.2CONFORMANCELIMIT ......................................................................................................... 12 7.3TESTCONFIGURATION ....................................................................................................... 12 7.4TESTPARAMETERSOFDFSTESTSIGNAL ........................................................................ 13 7.5TRANSMITTEROUTPUTPOWER .......................................................................................... 14 7.6OPERATIONMODESANDREQUIREMENTTESTITEMS ........................................................ 15 7.7TESTPROCEDURE ............................................................................................................... 15 8.TESTRESULT ....................................................................................................................... 16 8.1DETAILEDTESTRESULTS ............................................................................................ 16 8.2RADARWAVEFORM ............................................................................................................. 17 8.3IN-SERVICEMONITORING .................................................................................................... 20 8.4NON-OCCUPANCYPERIOD ....................................................................................... 23 ReportNo.ES200117042W05Page3of23Ver.1.0 1.TESTRESULTCERTIFICATION Applicant:ShenzhenGreatPowerInnovationandTechnologyEnterpriseCo.,Ltd Address: BuildingE,XinXulongIndustrialArea,KukengVillage,GuanlanTown,Longhua NewDistrict,Shenzhen,China Manufacturer:ShenzhenGreatPowerInnovationandTechnologyEnterpriseCo.,Ltd Address： BuildingE,XinXulongIndustrialArea,KukengVillage,GuanlanTown,Longhua NewDistrict,Shenzhen,China EUT:SmartSpeaker ModelName:D14U Trademark:KONKA MeasurementProcedureUsed: APPLICABLESTANDARDS STANDARDTESTRESULT FCC47CFRPart2,SubpartJ FCC47CFRPart15,SubpartE PASS TheaboveequipmentwastestedbyEMTEK(SHENZHEN)CO.,LTD.Thetestdata,dataevaluation,test procedures,andequipmentconfigurationsshowninthisreportweremadeinaccordancewiththe proceduresgiveninANSIC63.10(2013)andtheenergyemittedbythesampleEUTtestedasdescribedin thisreportisincompliancewiththerequirementsofFCCRulesPart2andPart15.407. Thetestresultsofthisreportrelateonlytothetestedsampleidentifiedinthisreport. DateofTest:January18,2020toApril16,2020 Preparedby: MillChen/Editor Reviewer: SewenGuo/Supervisor Approve&AuthorizedSigner: LisaWang / Manager ReportNo.ES200117042W05Page4of23Ver.1.0 2.EUTDESCRIPTION Note:formoredetails,pleaserefertotheUser’smanualoftheEUT. CharacteristicsDescription ProductSmartSpeaker ModelNumberD14U WifiType UNII-1:5150MHz-5250MHzBand UNII-2A:with5250MHz-5350MHzBand UNII-2C:with5470MHz-5725MHzBand UNII-3with5725MHz-5850MHzBand WLANSupported 802.11a 802.11n(20MHzchannelbandwidth) 802.11n(40MHzchannelbandwidth) 802.11ac(20MHzchannelbandwidth) 802.11ac(40MHzchannelbandwidth) 802.11ac(80MHzchannelbandwidth) DataRate 802.11a:54/48/36/24/18/12/9/6Mbps 802.11n:upto600Mbps 802.11ac:upto1.733Gbps Modulation OFDMwithBPSK/QPSK/16QAM/64QAMfor802.11a/n; OFDMwithBPSK/QPSK/16QAM/64QAM/256QAMfor802.11ac; FrequencyRange UNII-2A:with5250MHz-5350MHzBand 5260-5320MHzfor802.11a; 5260-5320MHzfor802.11n(HT20); 5260-5320MHzfor802.11ac(HT20); 5270-5310MHzfor802.11n(HT40); 5270-5310MHzfor802.11ac(HT40); 5290MHzfor802.11ac(HT80); UNII-2C:with5470MHz-5725MHzBand 5500-5700…

Text truncated - open the document above for the full version.

TRFNO.FCC15/APage1of2ReportNo.:ES191115017WVer.1.0 TESTSETUPPHOTOGRAPHS 1.1.PhotosofConductedEmissionMeasurement 1.2.PhotosofRadiationEmissionMeasurement SpuriousEmissionTestSetup(Below1GHz) TRFNO.FCC15/APage2of2ReportNo.:ES191115017WVer.1.0 SpuriousEmissionTestSetup(Above1GHz) ----------------Theend----------------