2A22Z-V9H-N529-1Dash Cam

1. This product contains a one-year warranty. For details on warranty service, kindly contact local authorized distributors. 2. Non-electronic accessories are not covered by the warranty. After-sales service Safety Warning lntroduction and declaration of after-sales service ̇ Thank you for choosing the botslab dash cam. Please use only the accessories provided by the original manufacturer to avoid unexpected malfunctions or damage. Failure to use the product as outlined here, or connecting it with incompatible accessories, will result in your warranty becoming void. The company assumes no responsibility for any danger or damage caused by such unauthorized uses. If you dismantle or change the product housing, the warranty will also become invalid. ̇Our company is committed to constant improvement and sustainable development. As a result, we may modify and improve the product manual without advance notice to users. ̇Unless otherwise specified by applicable laws, the manual contents are provided based on the product's manufacturing conditions. Therefore, no explicit or tacit warranty of any kind is made for the correctness, reliability, or contents of the files. ̇The product manual is protected by copyright law. Copying, transmitting, distributing, or using it in other forms is forbidden without the written approval of botslab. List of Performance Faults of botslab Dash Cam NamePerformance fault Failure of functions listed in the product manual; No display or incorrect characters displayed on the screen; Failure during start-up or normal recording of image data。 Button control failure; Cracks in the housing caused by structural or material issues. Abnormal status or operation, or failure to charge properly with the designated charger. Mainframe of botslab dash cam Charger & charger cable 封底 封面 Installation 01 Install the car mount Product appearance Car mount Remove the vehicle mount from the accessory box Align the screw rod of the vehicle-mounted bracket with the card nut of the recorder host.Use the appropriate force and angle to tighten the screw. Prompt: After tightening the screws to fix the bracket and the host, please carefully check to ensure that they are securely connected.To prevent the bracket from loosening after installation, affecting the recording quality of the recording equipment As shown in the figure below, connect the power cord from the top of the windshield, passing through the A-pillar, Then, route it through the glove compartment at the co-driver's position, finally positioning it near the cigarette lighter socket, and connect it to the cigarette lighter power source. You can use the installation pry bar provided in the package box to embed the power cord under the sealant strip of the A-pillar. Please note that the position of the cigarette lighter socket may vary depending on the car model, therefore, this image is for reference only. If you need to fine-tune the recording angle of the recorder during use, it is recommended to rotate it in a clockwise direction. Precautions for use of the recorder ̇This product is an auxiliary (vehicle tachograph) product for safe driving. We are not responsible for any damage caused by malfunction, loss of information, or use of this product. ̇This product is an auxiliary device for recording images of the exterior of the vehicle. ̇Some functions may not be supported due to differences in driving and vehicle environments. Firmware upgrades are performed from time to time to further improve the product. ̇Firmware upgrades performed from time to time to further improve the product may result in changes to the product's performance, and sometimes it may not be possible to record video due to the environment in which it is used. ̇The driving images recorded by this product are for reference only, as the product may not be able to record video due to the usage environment.Therefore, the driving images recorded by this product are for reference only. ̇Although this product can record and save vehicle accident images, there is no guarantee that all accident images can be recorded. Minor collisions do not activate the crash sensor, so images may not be recorded in the dedicated folder. ̇Do not install or operate this product while the vehicle is in motion. ̇This product requires direct connection to the vehicle's power supply system, so please have it operated by a professional experienced in installation. ̇Do not use this product for long periods of time without starting the engine. ̇If there is doubt or uncertainty as to whether a medical device can be shielded, this device may interfere with the functioning of improperly protected medical devices. ̇If there is doubt or uncertainty as to whether a medical device can be shielded, this device may interfere with the functioning of improperly protected medical devices. Botslab Dash Cam V9H Quick Start Guide Hanging board Nuts screw rod Universal Ball Joint Product appearance *Battery compartment power interface *Battery Compartment Fastening Clip Recorder Bayonet Nut TF card slot Botslab Dashcam Album/Shutter KeyRecording/Switching Key Loudspeaker lens Setup/Power Key screenPower indicator light MIC 03 Install static cling sticker Please install the electrostatic sticker on the front windshield. Refer to the recommended area (within the dashed line frame) in the figure below for the specific location. Before installation, make sure the glass surface has been thoroughly wiped clean. During the installation process, it is essential to completely eliminate any air bubbles between the electrostatic sticker and the glass. Note: When installing the dashcam, it is recommended to place it at the center position above the front windshield. It can help ensure that the camera's field of view fully covers the line of sight in front of the vehicle. Please adhere the glass static electricity film on the dashed line box. 04 Paste Recorder Tear off the 3M adhesive protective film and stick the recorder b…

Text truncated - open the document above for the full version.

ShenzhenYushengCommunicationEquipmentCo.,LTD 110 V9H-N529-1Projectantennaspecification Customername:360 Customername:V9H-N529-1 Productname:Steelsheet Productspecification:WIFIantenna:Yangbaicopper21.66*8.07*0.3mm Materialcode:18600000012082 ChangeContentCV: order number editionstateStartandend date person liable page number remarks 1editio princeps editio princeps 2024-04-12LiJieyi11 TheSupplieracknowledgesthesignaturethat: Responsibleperson/dateIQC/dateReview/DateApproval/Date MD RF TheDemanderacknowledgesthesignature(pleasesenditbackafterconfirmation): Thedemander'sjudgmentresult:□qualified□unqualified Development&Design Engineer/Date SQEEngineer/DatePurchasingLeader/ Date DevelopmentManager approval/date Manufacturer: Room 411, Building 2, South Taiyun Chuanggu Park, Southeast Of The Intersection Of Guangming Avenue And Dongchang Road, Tangwei Community, Fenghuang Street, Guangming Dist., Shenzhen, Guagndong, China ShenzhenYushengCommunicationEquipmentCo.,LTD 210 catalogue 1.OVERVIEW......................................................................................................................................................3 1.1S COPEOFAPPLICATION......................................................................................................................................3 1.2PROJECTBASICINFORMATION...........................................................................................................................3 2.TECHNICALINDEXREQUIREMENTS.....................................................................................................3 2.1I NTRODUCTIONOFTESTITEMSANDEQUIPMENT.............................................................................................3 2.2ACTIVEREPORTING.............................................................................................................................................3 2.2.1T ESTINSTRUCTIONS........................................................................................................................................3 2.2.2ANTENNAS11PASSIVEPARAMETERS............................................................................................................4 2.2.3ANTENNAENVIRONMENTRECTIFICATION......................................................................................................4 2.2.4T ESTINGSITUATIONOFANTENNAEFFICIENCYPARAMETERS.........................................................................5 2.2.5PASSIVEORIENTATIONDIAGRAM.....................................................................................................................6 2.2.6C ONDUCTIONTEST..........................................................................................................................................6 2.2.7ACTIVEOTATESTING......................................................................................................................................7 3.STRUCTURALDRAWINGS.........................................................................................................................8 3.1S TEELSHEETANTENNA.......................................................................................................................................8 4.LISTOFMATERIALS.....................................................................................................................................9 5.PACKAGINGDIAGRAM............................................................................................................................10 (T HISFIGUREISONLYAPACKAGINGDIAGRAM , SUBJECTTOTHEACTUALMASSPRODUCTION ) ...............................10 ShenzhenYushengCommunicationEquipmentCo.,LTD 310 1.Overview 1.1Scopeofapplication Thisrequirementspecifiestheantennatechnicalrequirementsandmaterialrequirementsspecificationsfor V9H-N529-1 products. ThisrequirementappliestotheV9H-N529-1 Antennatypeselection,test,andacceptance. 1.2Projectbasicinformation Antennaname: V9H-N529-1 Antennafrequency: IEEE802.11b/g/n/ax/BLE Antennamaterial:shrapnel 2.Technicalindexrequirements 2.1Introductionoftestitemsandequipment inventorytestitem equipment ActivetestTRP,TISIntegratedtester,microwavedarkroom 2.2ActiveReporting 2.2.1Testinstructions Testtools:Agilent8960instrument,R&SCMW500,fullwavefarfieldETSdarkroom,highprecision positioningsystemanditscontrollerandcomputerwithautomatictestprogram Testenvironment:temperature22°C±3°C,humidity50%±15% Testmethod:DUTisfixedinthecenteroftheturntablewithHplane,onthesamehorizontallineas thecenterofthehornantenna. ThepositioningsystemenablestheDUTtorotateinthewholespheretosatisfythehigh-precision3D positioning.EachRFinstrumentandturntablecontrollercommunicatewiththePCwithautomatictestsoftware throughtheGPIBinterface. ShenzhenYushengCommunicationEquipmentCo.,LTD 410 2.2.2AntennaS11passiveparameters 2.2.3Antennaenvironmentrectification ShenzhenYushengCommunicationEquipmentCo.,LTD 510 2.2.4Testingsituationofantennaefficiencyparameters frequency point productiven ess% productiven essdb gain 2 4 002 4 .5 - 6.1 - 0.6 2 4 1025. 8- 5. 9- 0. 8 2 4 2026. 4- 5. 8- 0. 8 2 4 3026. 8- 5.70 2 44 027.5 - 5.6 - 0.6 2 4 5027.2 - 5.6 - 0.7 2 4 6026.7 - 5.7 - 0.6 2 4 7025.1 - 5. 8- 0.7 2 48 025.6 - 5. 9- 0. 8 2 49 025.7 - 5. 9- 0. 9 250025.1 - 6.0 - 0.5 ShenzhenYushengCommunicationEquipmentCo.,LTD 610 2.2.5passiveorientationdiagram 2.2.6Conductiontest Trans m issiontestTX（dB m )RXdB m ) CH 116.7 -8 7 2. 4-B m ode CH 716. 8-88 11M bs CH 1316.7 -88 Trans m issiontestTX （ dB m )RXdB m ) CH 116.2 - 72 2. 4-N m ode CH 716.3 - 72 M CS 7 CH 1316. 4- 72 ShenzhenYushengCommunicationEquipmentCo.,LTD 710 The 2. 4G-G m odeof 5 4 M bs Trans m issiontestTXdB m )RXdB m ) CH 016.2 - 75 CH 1 9 16.3 - 75 CH 3 9 16.2 - 75 2.2.7ActiveOTAtesting Trans m issiontestTX（dB m )RXdB m ) CH 111.5 -8 1.25 2. 4-B m ode CH 711.5 -8 1.26 CH 1312.2 -8 2.11 Trans m issiontestTX（dB m )RXdB m ) CH 110. 9- 66.1 2. 4-N m ode CH 711.2 - 66.3 CH 1311.2 - 66.2 The 2. 4G-G m ode Trans m issiontestTXdB m )RXdB m ) CH 011…

Text truncated - open the document above for the full version.

Page 1 of 13 Report No.: LGT24G018 Appendix - External Photographs of EUT Constructional Details Model: V9H-N529-1 Photo 1 Photo 2 Page 2 of 13 Report No.: LGT24G018 Photo 3 Photo 4 Page 3 of 13 Report No.: LGT24G018 Photo 5 Photo 6 Page 4 of 13 Report No.: LGT24G018 Photo 7 Photo 8 Page 5 of 13 Report No.: LGT24G018 Photo 9 Photo 10 Page 6 of 13 Report No.: LGT24G018 Photo 11 Photo 12 Page 7 of 13 Report No.: LGT24G018 Photo 13 Photo 14 Page 8 of 13 Report No.: LGT24G018 Photo 15 Photo 16 Page 9 of 13 Report No.: LGT24G018 Photo 17 Photo 18 Page 10 of 13 Report No.: LGT24G018 Photo 19 Photo 20 Page 11 of 13 Report No.: LGT24G018 Photo 21 Photo 22 Page 12 of 13 Report No.: LGT24G018 Photo 23 Photo 24 Page 13 of 13 Report No.: LGT24G018 Photo 25

Size: 2.1*5.2mm Dash Cam Model: V9H-N529-1 FCC ID: 2A22Z-V9H-N529-1

Page 1 of 8 Report No.: LGT24G018 Appendix - Internal Photographs of EUT Constructional Details Model: V9H-N529-1 Photo 1 Photo 2 Page 2 of 8 Report No.: LGT24G018 Photo 3 Photo 4 MAIN ANT Page 3 of 8 Report No.: LGT24G018 Photo 5 Photo 6 Page 4 of 8 Report No.: LGT24G018 Photo 7 Photo 8 Page 5 of 8 Report No.: LGT24G018 Photo 9 Photo 10 Page 6 of 8 Report No.: LGT24G018 Photo 11 Photo 12 Page 7 of 8 Report No.: LGT24G018 Photo 13 Photo 14 Page 8 of 8 Report No.: LGT24G018 Photo 15

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China RF TEST REPORT Product Name: Dash Cam Model Name: V9H-N529-1 FCC ID: 2A22Z-V9H-N529-1 Issued For : Botslab, Inc. 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT24G018HA02 Sample Received Date: Jul. 03, 2024 Date of Test: Jul. 03, 2024 – Jul. 22, 2024 Date of Issue: Jul. 22, 2024 Report No.: LGT24G018HA02 Page 2 of 8 TEST REPORT CERTIFICATION Applicant: Botslab, Inc. Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Manufacture: Botslab, Inc. Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Product Name: Dash Cam Trademark: Botslab Model Name: V9H-N529-1 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR §2.1091 KDB 447498 D01 General RF Exposure Guidance v06 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT24G018HA02 Page 3 of 8 TABLE OF CONTENTS 1 . GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST LABORATORY 5 2 . FCC 47CFR §2.1091 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 EUT OPERATION CONDITION 6 2.4 CLASSIFICATION 6 2.5 TEST RESULT 7 APPENDIX I - PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS 8 Report No.: LGT24G018HA02 Page 4 of 8 Revision History Rev. Issue Date Revisions 00 Jul. 22, 2024 Initial Issue Report No.: LGT24G018HA02 Page 5 of 8 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name: Dash Cam Trademark: Botslab Model Name: V9H-N529-1 Series Model: N/A Model Difference: N/A Frequency Bands: Bluetooth 2402~2480 MHz 2.4G WLAN 802.11b/g/n/ax(20MHz): 2412~2462MHz 802.11n/ax(40MHz):2422~2452MHz Adapter: Input: DC 12-24V Output: DC 5V 2.4A Battery: Rated Capacity: 1700mAh Rated Voltage: 3.8V Hardware Version: 2.0 Software Version: N/A 1.2 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate A2LA Certificate No.: 6727.01 FCC Registration No.: 746540 CAB ID: CN0136 Report No.: LGT24G018HA02 Page 6 of 8 2. FCC 47CFR §2.1091 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm²) Limits for Occupational / controlled Exposures 300 - 1500 -- -- F/300 1500 – 100000 -- -- 5.0 Limits for General population / Uncontrolled Exposure 300 - 1500 -- -- F/1500 1500 – 100000 -- -- 1.0 F= Frequency in MHz Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation, we will know MPE value at distance 20cm. 2.3 EUT OPERATION CONDITION EUT was enabled to transmit and receive at lowest, middle and highest channels. 2.4 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device. Report No.: LGT24G018HA02 Page 7 of 8 2.5 TEST RESULT Turn up Result Mode Turn up Power BLE-GFSK -2±1dBm 2.4G WIFI-802.11b 16±1dBm 2.4G WIFI-802.11g 15±1dBm 2.4G WIFI-802.11n(HT20) 13±1dBm 2.4G WIFI-802.11n(HT40) 12.5±1dBm 2.4G WIFI-802.11ax(HE20) 12.5±1dBm 2.4G WIFI-802.11ax(HE40) 11.5±1dBm The MPE result of worst mode: RF Function Frequenc y (MHz) Max Turn up Power (dBm) Max Turn up Power (mW) ANT Gain (dBi) ANT Gain (gain of antenna in linear scale) Power Density (mW/cm ²) Limit (mW/cm²) Ratio Resul t BT 2480 -1.00 0.79 0 1.00 0.0002 1 0.0002 Pass 2.4G WIFI 2462 17.00 50.12 0 1.00 0.0100 1 0.0100 Pass Note: 1. The Bluetooth and WLAN can’t simultaneous transmission at the same time. 2. The Maximum Power Density is less than the limit, complies with the exemption requirements. Report No.: LGT24G018HA02 Page 8 of 8 APPENDIX I - PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Note: Please see the attached V9H-N529-1_EUT Photos. ※※※※※END OF THE REPORT※※※※※

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China RF TEST REPORT Product Name: Dash Cam Model Name: V9H-N529-1 FCC ID: 2A22Z-V9H-N529-1 Issued For : Botslab, Inc. 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT24G018RF03 Sample Received Date: Jul. 03, 2024 Date of Test: Jul. 03, 2024 – Jul. 22, 2024 Date of Issue: Jul. 22, 2024 Report No.: LGT24G018RF03 Page 2 of 48 TEST REPORT CERTIFICATION Applicant: Botslab, Inc. Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Manufacturer: Botslab, Inc. Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Product Name: Dash Cam Trademark: Botslab Model Name: V9H-N529-1 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2013 KDB558074 D01 15.247 Meas Guidance v05r02 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT24G018RF03 Page 3 of 48 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 9 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 10 2.5 EQUIPMENTS LIST 11 3. EMC EMISSION TEST 12 3.1 CONDUCTED EMISSION MEASUREMENT 12 3.2 TEST PROCEDURE 13 3.3 TEST SETUP 13 3.4 EUT OPERATING CONDITIONS 13 3.5 TEST RESULTS 14 4. RADIATED EMISSION MEASUREMENT 16 4.1 RADIATED EMISSION LIMITS 16 4.2 TEST PROCEDURE 18 4.3 TEST SETUP 18 4.4 EUT OPERATING CONDITIONS 19 4.5 FIELD STRENGTH CALCULATION 19 4.6 TEST RESULTS (BAND EDGE REQUIREMENTS) 25 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 27 5.1 LIMIT 27 5.2 TEST PROCEDURE 27 5.3 TEST SETUP 27 5.4 EUT OPERATION CONDITIONS 27 5.5 TEST RESULTS 27 6. POWER SPECTRAL DENSITY TEST 28 6.1 LIMIT 28 6.2 TEST PROCEDURE 28 6.3 TEST SETUP 28 6.4 EUT OPERATION CONDITIONS 28 Report No.: LGT24G018RF03 Page 4 of 48 6.5 TEST RESULTS 28 7. BANDWIDTH TEST 29 7.1 LIMIT 29 7.2 TEST PROCEDURE 29 7.3 TEST SETUP 29 7.4 EUT OPERATION CONDITIONS 29 7.5 TEST RESULTS 29 8. PEAK OUTPUT POWER TEST 30 8.1 LIMIT 30 8.2 TEST PROCEDURE 30 8.3 TEST SETUP 30 8.4 EUT OPERATION CONDITIONS 30 8.5 TEST RESULTS 30 9. ANTENNA REQUIREMENT 31 9.1 STANDARD REQUIREMENT 31 9.2 EUT ANTENNA 31 APPENDIX I - TEST RESULTS 32 DUTY CYCLE 32 MAXIMUM PEAK CONDUCTED OUTPUT POWER 34 -6DB BANDWIDTH 35 OCCUPIED CHANNEL BANDWIDTH 37 MAXIMUM POWER SPECTRAL DENSITY LEVEL 39 BAND EDGE 41 CONDUCTED RF SPURIOUS EMISSION 44 APPENDIX II - MEASUREMENT PHOTOS 47 APPENDIX III - PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS 48 Report No.: LGT24G018RF03 Page 5 of 48 Revision History Rev. Issue Date Revisions 00 Jul. 22, 2024 Initial Issue Report No.: LGT24G018RF03 Page 6 of 48 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 Part 15.247 Meas Guidance v05r02. FCC Part 15.247, Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2013. Report No.: LGT24G018RF03 Page 7 of 48 1.1 TEST FACTORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate A2LA Certificate No.: 6727.01 FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.68dB 2 Unwanted Emissions, conducted ±2.988dB 3 All emissions, radiated 9K-30MHz ±2.84dB 4 All emissions, radiated 30M-1GHz ±4.39dB 5 All emissions, radiated 1G-6GHz ±5.10dB 6 All emissions, radiated>6G ±5.48dB 7 Conducted Emission (9KHz-150KHz) ±2.79dB 8 Conducted Emission (150KHz-30MHz) ±2.80dB Note: The measurement uncertainty is not included in the test result. Report No.: LGT24G018RF03 Page 8 of 48 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Dash Cam Trademark: Botslab Model Name: V9H-N529-1 Series Model: N/A Model Difference: N/A Product Description: Operation Frequency: 2402~2480 MHz Modulation Type: GFSK Radio Technology: BLE Bluetooth Configuration: BLE (1M PHY) Number Of Channel: 40 Antenna Designation: Metal Antenna Antenna Gain (dBi) 0dBi Channel List: Please refer to the Note 3. Adapter: Input: DC 12-24V Output: DC 5V 2.4A Battery: Rated Capacity: 1700mAh Rated Voltage: 3.8V Hardware Version: 2.0 Software Version: N/A Connecting I/O Port(s): Please refer to the Note 1. Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User Manual. 2. The antenna information refers to the man…

Text truncated - open the document above for the full version.

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China RF TEST REPORT Product Name: Dash Cam Model Name: V9H-N529-1 FCC ID: 2A22Z-V9H-N529-1 Issued For : Botslab, Inc. 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT24G018RF04 Sample Received Date: Jul. 03, 2024 Date of Test: Jul. 03, 2024 – Jul. 22, 2024 Date of Issue: Jul. 22, 2024 Report No.: LGT24G018RF04 Page 2 of 85 TEST REPORT CERTIFICATION Applicant: Botslab, Inc. Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Manufacturer: Botslab, Inc. Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA Product Name: Dash Cam Trademark: Botslab Model Name: V9H-N529-1 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2013 KDB558074 D01 15.247 Meas Guidance v05r02 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT24G018RF04 Page 3 of 85 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 10 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 RADIATED EMISSION MEASUREMENT 17 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 28 4.1 LIMIT 28 4.2 TEST PROCEDURE 28 4.3 DEVIATION FROM STANDARD 28 4.4 TEST SETUP 28 4.5 EUT OPERATION CONDITIONS 28 4.6 TEST RESULTS 28 5. POWER SPECTRAL DENSITY TEST 29 5.1 LIMIT 29 5.2 TEST PROCEDURE 29 5.3 DEVIATION FROM STANDARD 29 5.4 TEST SETUP 29 5.5 EUT OPERATION CONDITIONS 29 5.6 TEST RESULTS 29 6. BANDWIDTH TEST 30 6.1 LIMIT 30 6.2 TEST PROCEDURE 30 6.3 DEVIATION FROM STANDARD 30 6.4 TEST SETUP 30 6.5 EUT OPERATION CONDITIONS 30 6.6 TEST RESULTS 30 Report No.: LGT24G018RF04 Page 4 of 85 7. PEAK OUTPUT POWER TEST 31 7.1 LIMIT 31 7.2 TEST PROCEDURE 31 7.3 DEVIATION FROM STANDARD 31 7.4 TEST SETUP 31 7.5 EUT OPERATION CONDITIONS 31 7.6 TEST RESULTS 31 8. ANTENNA REQUIREMENT 32 8.1 STANDARD REQUIREMENT 32 8.2 EUT ANTENNA 32 APPENDIX I - TEST RESULTS 33 DUTY CYCLE 33 MAXIMUM PEAK CONDUCTED OUTPUT POWER 40 -6DB BANDWIDTH 41 OCCUPIED CHANNEL BANDWIDTH 48 MAXIMUM POWER SPECTRAL DENSITY LEVEL 55 BAND EDGE 62 CONDUCTED RF SPURIOUS EMISSION 71 APPENDIX II - MEASUREMENT PHOTOS 84 APPENDIX III - PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS 85 Report No.: LGT24G018RF04 Page 5 of 85 Revision History Rev. Issue Date Revisions 00 Jul. 22, 2024 Initial Issue Report No.: LGT24G018RF04 Page 6 of 85 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2013. Report No.: LGT24G018RF04 Page 7 of 85 1.1 TEST FACTORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate A2LA Certificate No.: 6727.01 FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF Output Power, Conducted ±0.71dB 2 Power Spectral Density, Conducted ±1.57 dB 3 Unwanted Emission, Conducted ±0.63dB 4 Conducted emission ±2.80dB 5 All Emi…

Text truncated - open the document above for the full version.