2A29L-SMIT002IMMOBILIZER

IMMOBILIZER (SMIT002): IMMOBILIZER User manual: Technical Specifications: 1. Operating voltage shall be 8 V to 18 V. 2. Operating temperature shall be -2 0°C to +60°C. 3. Rated voltage shall be 12V. 4. Authentication between Immo and key transponder shall happen within 250 ms of IGN ON. And maximum up to 1 sec with 5-retries. 5. Immo shall send random number RNimmo of 7 Bytes after receiving RNvcu and retries up to 3-retries. 6. Immo shall send random number R7vcu of 7Bytes after receiving R7immo and retries up to 3-retries. Features and Functions: 1. Mutual Authentication of the genuine Mechanical key embedded with Transponder and Immo. a. IMMOBILIZER shall authenticate the Transponder embedded inside the Mechanical key(PCF7938X) using HITAG-3 encryption. 2. Mutual Authentication of the vehicle EMS. After successful authentication of IMMOBILIZER and Transponder, Immo shall perform authentication between the vehicle EMS using AES- 128 encryption. • IMMOBILIZER that incorporates additional element of security in classic mechanical lock with transponder chip embedded in the Mechanical key. • The IMMOBILIZER will communicate with Key transponder chip through LF coil Antenna embedded in the lockset. • NXP HITAG3 encryption algorithm is used between key transponder chip & IMMOBILIZER for authentication.  Transponder: • Transponder is a wireless communication, monitoring or control device that picks up and automatically responds to an incoming LF signal. • The primary purpose of automotive transponder is to prevent unauthorized access and theft. Working: • Transponder functions on inductive coupling, when the transponder key is near to the LF coil antenna embedded in the mechanical lock set, generates LF field and energise the transponder key which send a unique code to the vehicle IMMOBILIZER. • After successful pairing between transponder and IMMOBILIZER, further vehicle authentication shall be allowed.  IMMOBILIZER: • An IMMOBILIZER is a security device connected to the lock set of a vehicle that prevents the engine from starting unless the correct transponder key is present. • IMMOBILIZER system is an antitheft system significantly enhances vehicle security by making it much more difficult for thieves to start the vehicle without authorization. • IMMOBILIZER shall authenticate the Transponder embedded inside the Mechanical key using HITAG-3 encryption. FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC Caution: This device complies with Innovation, Science, and Economic Development Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. FCC/IC Radiation Exposure Statement: This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. L'appareil est conforme aux limites d'exposition aux rayonnements spécifiées par la FCC/ISED pour les environnements non contrôlés. La distance entre le radiateur et le corps doit être d'au moins 20 cm lors de l'installation et du fonctionnement de l'appareil. Manufacturer Company: Minda Corporation Limited Address: D-6 -11, Sector 59, Noida, U.P.- 201301 For UKCA Frequency/ Power: 125 kHz(28.71dBμA/m@3m)

[ MINDA l MINDA CORPORATION LIMITED ,_______ (SECURITY SYSTEM DIVISION) -----Poweredtrf�tAGENT LETTER OF ATTESTATION Date: Jun 25, 2026 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.91 l(d)(7) Filing FCC ID: 2A29L-SMIT002 Minda Corporation Limited certifies that, as of the date of the filing of the application, EMCTEK. is our designated U.S. agent for service of process for the above referenced FCC ID. Minda Corporation Limited accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. EMCTEK accepts, as of the date of the filing of the application, the obligation of the designat_ed U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name:EMCTEK Address: 11788 Big Canyon Lane San Diego, CA 92131 United States FRN :0037012671 Tel.:8584019073 Email: [email protected] Signed by (printed name):Fang Liu Signature: Applicant: Minda Corporation Limited Address: D6-l 1, Sector-59, Noida, India FRN: 00313 88986 .Tel:+91 8222812333 Email: [email protected] Signed by (printed name)· Fahim Uddin Signatu r e: F o r Min d a Co r orati on Limite d Au MINDA CORPORATION LIMITED (SECURITY SYSTEM DIVISION) CIN: L74899DL 1985PLC020401 Office Address : D-6-11, Sector-59, Noida, Uttar Pradesh - 201301, India. Tel. : +91-120-4787100; Fax : +91-120-4787201 Registered Office : A-15, Ashok Vihar, Phase - I, Delhi - 110052. Website : www.sparkminda.com

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-EXP Page 1 of 4 EUT EXTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-EXP Page 2 of 4 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-EXP Page 3 of 4 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-EXP Page 4 of 4

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2601T23244E-RF FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-INP Page 1 of 3 EUT INTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-INP Page 2 of 3 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-INP Page 3 of 3 ANT

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF TR-EM-RF314 Page 11 of 28 Version 3.0 FCC §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.346141.63*(100)30 1.34–30824/f2.19/f*(180/f²)30 30–30027.50.0730.230 300–1500//f/150030 1500–100,000//1.030 f = frequency in MHz; * = Plane-wave equivalent power density; Block Diagram of Test Setup Test Procedures 1) Perform H-field and E-field measurements for each all sides of the EUT at 20cm, along all the principal axes defined with respect to the orientation of the transmitting element (e.g., coil or antenna). 20cm Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF TR-EM-RF314 Page 12 of 28 Version 3.0 Test Data Environmental Conditions Temperature: 25.7 °C Relative Humidity: 51 % ATM Pressure: 100.9 kPa The testing was performed by Zane Zhou on 2026-08-12. Test mode: Transmitting H-Field Strength Test Frequency (kHz) Position A (A/m) Position B (A/m) Position C (A/m) Position D (A/m) Position E (A/m) Position F (A/m) Limit (A/m) 1250.010.010.010.01 0.05 0.021.63 E-Field Strength Test Frequency (kHz) Position A (V/m) Position B (V/m) Position C (V/m) Position D (V/m) Position E (V/m) Position F (V/m) Limit (V/m) 1252.121.661.391.671.761.39614 Note: Test with 20cm distance from all the sides.

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF314 Page 1 of 28 Version 3.0 TEST REPORT Applicant Name:Minda Corporation Limited Address:FCC: D6-11, Sector-59, Noida, India IC: D6-11, Sector-59 Distt. G.B. Nagar U.P. 201301 India Report Number:2601T23244E-RF FCC ID:2A29L-SMIT002 IC:23641-SMIT002 Test Standard (s) FCC Part 15C; RSS-GEN ISSUE 5, FEBRUARY 2021 AMENDMENT 2; RSS-210, ISSUE 11, JUNE 25, 2024 Sample Description Product Type:IMMOBILIZER Model No.:SMIT002 Multiple Model(s) No.:N/A Trade Mark:Spark RE Date Received:2026/05/26 Issue Date:2026/08/13 Test Result:Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By:Approved By: Cheeb HuangJimmy Xiao RF EngineerEMC Manager Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF TR-EM-RF314 Page 2 of 28 Version 3.0 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ..........................................................................................................................3 GENERAL INFORMATION ........................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)......................................................................................4 OBJECTIVE ....................................................................................................................................................................4 TEST METHODOLOGY....................................................................................................................................................4 MEASUREMENT UNCERTAINTY .....................................................................................................................................5 TEST FACILITY ..............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ...........................................................................................................................6 DESCRIPTION OF TEST CONFIGURATION .......................................................................................................................6 EUT EXERCISE SOFTWARE ...........................................................................................................................................6 LOCAL SUPPORT EQUIPMENT ........................................................................................................................................6 EXTERNAL I/O CABLE...................................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................................6 SUMMARY OF TEST RESULTS ................................................................................................................................7 TEST EQUIPMENT LIST ............................................................................................................................................8 FCC §15.203 & RSS-GEN §6.8 - ANTENNA REQUIREMENT ...............................................................................9 APPLICABLE STANDARD ...............................................................................................................................................9 ANTENNA CONNECTED CONSTRUCTION .....................................................................................................................10 FCC §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE (MPE)..........................................................................11 APPLICABLE STANDARD .............................................................................................................................................11 BLOCK DIAGRAM OF TEST SETUP ...............................................................................................................................11 TEST PROCEDURES ......................................................................................................................................................11 TEST DATA..................................................................................................................................................................12 FCC §15.205, §15.209, RSS-GEN §8.9 & RSS-210 §8.3 - RADIATED EMISSIONS TEST .................................13 APPLICABLE STANDARD .............................................................................................................................................13 EUT SETUP ...........................................................................................................................................................…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-TSP Page 1 of 5 EXHIBIT D - TEST SETUP PHOTOGRAPHS Radiated Emissions View (9 kHz-30 MHz) - Perpendicular Radiated Emissions View (9 kHz-30 MHz) - Parallel Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-TSP Page 2 of 5 Radiated Emissions View (9 kHz-30 MHz) - Ground-parallel Radiated Emissions View (30 MHz- 1 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-TSP Page 3 of 5 A Side B Side Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-TSP Page 4 of 5 C Side D Side Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601T23244E-RF-TSP Page 5 of 5 E Side F Side