2A4A7-PTM-603smart water dispenser

PTM-603 Instruction Manual Please read the manual carefully before using the product Basic parameters Product name: smart water dispenser Product model: PTM-603 Product color: transparent white Overall storage size: 176*176*141.8mm Capacity: 2L Material: ABS Input:5V/1A product description packing list Water dispenser host * 1 Wireless Water Pump* 1 Filter element* 1 Charging cable* 1 Filter sponge* 1 Instruction Manual* 1 Small brush* 1 Whole machine installation 1， Reverse the wireless charging bottom cover and connect the power cable 2， Remove the top cover and filter grid and adjust the position of the pump 3， The amount of water added refers to the scale line of the machine's large barrel 4， After filling with water, put the filter grid first, then the top cover 5， After installation, it can be placed on the wireless charging base for use Product usage guidelines 1， Take out the machine, after the whole machine is installed, it can be used after placing the wireless charging base (the default green light of the machine is always on when the power is turned on for the first time and continues to water out mode) 2， The single-machine base button switches the light selection (green light is always on - colorful always - no light) the water outlet mode is still continuous water outlet 3， Double-click the base button to switch the light selection (green light breathing - colorful breathing - no light) the water outlet mode becomes intermittent water outlet (3 minutes on and 3 minutes off) 4， After adjusting the mode, it can be used normally. Product Cleaning Guidelines 1， The machine is removed from the base, and the whole machine is washable 2， Take out the machine parts and wash them in sequence Pump Cleaning Guidelines 1， Remove the water pump from the water dispenser bucket and pull out the drainage tube 2， Take out the filter sponge 3， Open the water pump filter box along the gap 4， Remove the water pump impeller cover 5， Use a small tool to remove the water pump impeller 6， Carefully clean every part safety warning 1， Recommended for pets over 3 months old 2， Do not touch the power supply unit of the device with wet hands. 3， recommended to be used indoors, do not place in humid environments such as outdoor and bathroom, avoid direct sunlight , humidity, and keep away from fire sources . 4， Please use the original power adapter, otherwise the equipment will be damaged or unable to work. Do not use damaged power cords or plugs. 5， When unplugging the power supply unit, please hold the adapter with your hand to unplug it, do not drag the power cord. Use a safety low-voltage adapter rated for this equipment. 6， Do not immerse the wireless charging base in water or any other liquid for use. After the base is wet, please wipe the surface dry before continuing to use it. 7， 60 ° in the bucket . 8， To prevent pets from falling over, it is recommended to use against the wall 9， Children under the age of 8 are not allowed to use this equipment, and children are not allowed to clean and maintain the equipment without adult supervision! This device is different from toys, and minors must use this device under parental supervision. Be sure to prevent children from playing with the device as a toy. 10， If the device fails to work properly due to being dropped, bumped, damaged, placed outdoors, or flooded, please stop using it immediately. 11， Except for maintenance personnel, please do not disassemble and repair the product, otherwise all warranty and service rights will be lost 12， Please do not place coins, keys and other metal parts in the wireless base transmitting area, it will cause the machine to malfunction. Device Indicator Description 1， The machine intermittently discharges water (3 minutes off, 3 minutes on): the green light is breathing and flashing 2， The machine continues to water: the green light is always on 3， The machine intermittently discharges water (stop for 3 minutes, open for 3 minutes): the colorful lights are breathing and flashing 4， The machine continuously discharges water: the colorful lights are always on 5， The machine can also turn off the light during intermittent and continuous water discharge. 6， The machine is short of water: the red light flashes 7， The pump is not placed in the position or the position of the pump is shifted: the red light flashes Machine Troubleshooting Guide A:red light flashing 1， Check that the pump is properly seated in the groove of the sink 2， Check whether there are foreign objects between the bottom of the pump and the bucket, and whether there are foreign objects between the bucket and the base 3， Check if the amount of water is sufficient, if not, please add water 4， Check if a compliant adapter is used B : The red light is bad and the green light is always on or the colorful light is always on, but the water pump is not running 1， Please check whether the pump impeller is blocked, if it is blocked, please clean it 2， Check if the amount of water is sufficient, if not, please add water C: The indicator light is off, and the water pump is not running 1， Please check if the power supply is connected 2， Please check whether the pump impeller is blocked, if it is blocked, please clean it 3， Check if the amount of water is sufficient, if not, please add water D: The water volume of the pump is small 1， Please check whether the water outlet of the equipment is installed properly 2， Please check if the sponge is blocked, clean or replace the sponge 3， Check for hair entering the pump, clean the pump impeller E : The water pump has noise 1， Please check whether the water outlet of the equipment is installed properly 2， Check if the amount of water is sufficient, if not, please add water 3， Check for hair entering the pump, clean the pump impeller F : The water pump is sometimes out of water and sometimes out of water 1， Check if the amount of water is sufficient, if not, please add water 2， Please check whether to use intermittent wate…

Text truncated - open the document above for the full version.

Letter of Declaration Company: Shenzhen Ipetmon Creative Technology Co., Ltd. Address: Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Product Name: smart water dispenser Trade Mark: iPetmon Model Number: PTM-603, PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 FCC Identifier: 2A4A7-PTM-603 Compliant with KDB 680106 D01 RF Exposure Wireless Charging Apps v03 section 5, b: a) Power transfer frequency is less than 1MHz. Yes, the working frequency is 125KHz. b) Output power from each primary coil is less than or equal to 15 watts. Yes, the maximum output power is 15 watts. c) The transfer system includes only single primary coil. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Yes, the transfer system includes only single primary coil. d) Client device is placed directly in contact with the transmitter. Yes, client device is placed directly in contact with the transmitter. e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes, EUT is for mobile exposure conditions only. f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Yes, EUT h-field strengths levels are less than 50% of the MPE limit. Name: Deng Kaiqi Date: Jul. 29, 2022 Title: Manager Signature of applicant:

Date: Jul. 29, 2022 < Shenzhen Ipetmon Creative Technology Co., Ltd. > Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Subject; Request for Long Term Confidentiality FCC ID: 2A4A7-PTM-603 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Deng Kaiqi Title: Manager

Shenzhen Ipetmon Creative Technology Co., Ltd. Letter of Authorization Company: Shenzhen Ipetmon Creative Technology Co., Ltd. Address: Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Product name: smart water dispenser Trade name: iPetmon Model name: PTM-603, PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 FCC Identifier: 2A4A7-PTM-603 We authorize MiCOM LabsInc, 575 Boulder Court, Pleasanton, California94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM LabsInc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Deng Kaiqi Date: Jul. 29, 2022 Title: Manager Signature of applicant:

Model: PTM-603 Model: PTM-603 Model: PTM-603 Model: PTM-603

FCC ID LABEL: Label Location: FCC ID: 2A4A7-PTM-603 Product Name: smart water dispenser Model Name: PTM-603 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Long: 3cm Width: 2cm

Model: PTM-603 Model: PTM-603 Model: PTM-603 Model: PTM-603 Model: PTM-603 Coil Antenna

Page 1 / 10 FCC MPE TEST REPORT FCC ID: 2A4A7-PTM-603 Sample： smart water dispenser Trade Name： iPetmon Main Model： PTM-603 Additional Model： PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 Report No.： UNIA22072004ER-62 Prepared for Shenzhen Ipetmon Creative Technology Co., Ltd. Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China Page 2 / 10 TEST RESULT CERTIFICATION Applicant ............................... : Shenzhen Ipetmon Creative Technology Co., Ltd. Address .................................. : Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Manufacturer ........................ : Shenzhen Ipetmon Creative Technology Co., Ltd. Address .................................. : Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Product description Product ....................................... : smart water dispenser Trade Name ........................... : iPetmon Model Name ........................... : PTM-603, PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 Standards ......................... : FCC KDB 680106 D01 RF Exposure Wireless Charging Apps v03 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test ........................................... : Date (s) of performance of tests ............ : Jul. 20, 2022 ~ Jul. 23, 2022 Date of Issue ......................................... : Jul. 29, 2022 Test Result ............................................. : Pass Prepared by: Kahn yang/Supervisor Reviewer: Kelly Cheng/Supervisor Approved & Authorized Signer: Liuze/Manager Page 3 / 10 Note: For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Channel List Channel Frequency(KHz) Channel Frequency(MHz) 01 125 The EUT antenna is Coil Antenna. No antenna other than that furnished by the responsible party shall be used with the device. 1. SUMMARY OF TEST RESULTS 1.1 Test procedures according to the technical standards: FCC KDB 680106 D01 RF Exposure Wireless Charging Apps v03 FCC CFR 47 Standard Section Test Item Judgment Remark FCC CFR 47 part1, 1.1310 KDB680106 D01 v03(3)(3) Electric Field Strength (E) (V/m) PASS Magnetic Field Strength (H) (A/m) PASS Compliant with KDB680106 D01 RF Exposure Wireless Charging Apps v03 section 5, b: a) Power transfer frequency is less than 1MHz. Yes, the working frequency is 125KHz. b) Output power from each primary coil is less than or equal to 15 watts. Yes, the maximum output power is 15 watts. c) The transfer system includes only single primary coil. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Yes, the transfer system includes only single primary coil. d) Client device is placed directly in contact with the transmitter. Yes, client device is placed directly in contact with the transmitter. e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes, EUT is for mobile exposure conditions only. f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Yes, EUT h-field strengths levels are less than 50% of the MPE limit. Page 4 / 10 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Radiated Measurement (9KHz-30MHz) ±2.50dB 2 Temperature ±0.5°C 3 Humidity ±2% 1.3 Test Instruments Description Brand Model No. Frequency Range Calibrated Until Broadband Field Meter NARDA NBM-550 –– Jan. 01, 2023 Magnetic Field Meter NARDA ELT-400 1–400kHz Jan. 01, 2023 Magnetic Probe NARDA HF-3061 300kHz–30MHz Jan. 01, 2023 Magnetic Probe NARDA HF-0191 27–1000MHz Jan. 01, 2023 Broadband Field Meter NARDA NBM-550 –– Jan. 01, 2023 Electric Field Meter COMBINOVA EFM 200 5Hz–400kHz Jan. 01, 2023 E-Field Probe NARDA EF-0391 100kHz–3GHz Jan. 01, 2023 E-Field Probe NARDA EF-6091 100MHz–60GHz Jan. 01, 2023 NOTE: The calibration interval of the above test instruments is 12 months. Page 5 / 10 2. MAXIMUM PERMISSIBLE EXPOSURE 2.1 MAXIMUM PERMISSIBLE EXPOSURE Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180 / f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1 30 Note 1: f = frequency in MHz ; *Plane-w…

Text truncated - open the document above for the full version.

Page 1 of 22 Report No.: UNIA22072004ER-61 FCC RADIO TEST REPORT FCC ID: 2A4A7-PTM-603 Sample： smart water dispenser Trade Name： iPetmon Main Model： PTM-603 Additional Model： PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 Report No.： UNIA22072004ER-61 Prepared for Shenzhen Ipetmon Creative Technology Co., Ltd. Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China Page 2 of 22 Report No.: UNIA22072004ER-61 TEST RESULT CERTIFICATION Applicant .............................. : Shenzhen Ipetmon Creative Technology Co., Ltd. Address ................................. : Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Manufacturer ........................ : Shenzhen Ipetmon Creative Technology Co., Ltd. Address ................................. : Complete set of Building 10,Meibao Industrial Zone, Liantang Industrial Zone, Shangcun Community, Gongming Street, Guangming District, Shenzhen, China Product description Product ....................................... : smart water dispenser Trade Name ........................... : iPetmon Model Name .......................... : PTM-603, PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 Test Methods ........................ : FCC Rules and Regulations Part 15 Subpart C Section 15.209 ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test ........................................... : Date (s) of performance of tests ............. : Jul. 20, 2022 ~ Jul. 23, 2022 Date of Issue .......................................... : Jul. 29, 2022 Test Result.............................................. : Pass Prepared by: Kahn yang/Supervisor Reviewer: Kelly Cheng/Supervisor Approved & Authorized Signer: Liuze/Manager Page 3 of 22 Report No.: UNIA22072004ER-61 Table of Contents Page 1 TEST SUMMARY 4 2 GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 CARRIER FREQUENCY OF CHANNELS 7 2.3 TEST MODE 7 2.4 TEST SETUP 7 2.5 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 8 2.6 MEASUREMENT INSTRUMENTS LIST 9 3 CONDUCTED EMISSION 10 3.1 TEST LIMIT 10 3.2 TEST SETUP 10 3.3 TEST PROCEDURE 11 3.4 TEST RESULT 11 4 RADIATED EMISSION 14 4.1 TEST LIMIT 14 4.2 TEST SETUP 16 4.3 TEST PROCEDURE 17 4.4 TEST RESULT 17 5 ANTENNA REQUIREMENT 20 6 PHOTO OF TEST 21 6.1 RADIATED EMISSION 21 6.2 CONDUCTED EMISSION 22 Page 4 of 22 Report No.: UNIA22072004ER-61 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS ITEM STANGARD RESULT CONDUCTED EMISSION FCC Part 15.207 COMPLIANT RADIATED EMISSION FCC Part 15.209 COMPLIANT ANTENNA REQUIREMENT FCC Part 15.203 COMPLIANT 1.2 TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address : 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: A2LA Certificate Number: 4747.01 The EMC Laboratory has been accredited by A2LA, and in compliance with ISO/IEC 17025:2017 General Requirements for testing Laboratories. FCC Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. IC Registration Number: 21947 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. Page 5 of 22 Report No.: UNIA22072004ER-61 1.3 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. A. Conducted Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 150KHz 2.96 150KHz ~ 30MHz 2.44 B. Radiated Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 30MHz 2.50 30MHz ~ 1000MHz 4.80 1000MHz ~ 6000MHz 4.13 Page 6 of 22 Report No.: UNIA22072004ER-61 2 GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product: smart water dispenser Trade Name: iPetmon Main Model: PTM-603 Additional Model: PTM-613, PTM-623, PTM-633, PTM-643, PTM-653, PWF-01 Model Difference: All model’s the function, software and electric circuit are the same, only with a product color and model named different. Test sample model: PTM-603. FCC ID: 2A4A7-PTM-603 Operation Frequency: 125KHz Number of Channels: 1CH Modulation Type: ASK Antenna Type: Coil Antenna Antenna Gain: 0dBi Battery: N/A Adapter: M/N: QL010-0501000UU Input: AC 100-240V, 50/60Hz, 0.45A Output: DC 5.0V, 1.0A Power Source: DC 5V from adapter with AC 120(240)V/60Hz Page 7 of 22 Report No.: UNIA22072004ER-61 2.2 CARRIER FREQUENCY OF CHANNELS Channel List Channel Frequency (KHz) Channel Frequency (KHz) Channel Frequency (KHz) Channel Frequency (KHz) 01 125 2.3 TEST MODE The EUT was programmed to be in transmitting mode. Channel List Test Channel Test Frequency (KHz) 01 125 2.4 TEST SETUP Operation…

Text truncated - open the document above for the full version.

Model: PTM-603 Radiated Emission test Model: PTM-603 Conducted Emission test