2A4UPT500MV1000Portable Power Station

制作要求 此页不印刷 物料名称：T500中性（美规）说明书 物料编码：3.06.03.0100 成品尺寸：142x210mm 展开尺寸：284x210mm 钉装：骑马钉 材质：铜版纸 哑光 版本：V1.1 日期：2022-02-21 BRAND USER MANUAL T-500 To make sure your personal safety, property security and user experience, please read this manual carefully before operating,and retain it for future reference. Before using your new Power Station T-500 or after storing it for more than 3 months, plug it into a suitable wall outlet until it is fully charged.Then you can start your exciting journey with it. CHARGE FIRST! Thank you for purchasing T-500 portable power station Safety instructions 1 . Read all the instructions before using the product. To reduce the risk of injury, close supervision is necessary when the product is used near children. Do not put fingers or hands into the product. Use of an attachment not recommended or sold by power pack manufacturer may result in a risk of fire, electric shock, or injury to persons. To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the power pack. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. Do not operate the power pack with a damaged cord or plug, or a damaged output cable. Do not disassemble the power pack, take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock. To reduce the risk of electric shock, unplug the power pack form the outlet before attempting any instructed servicing. WARNING - RISK OF EXPLOSIVE GASES. To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in vicinity of the battery. Review cautionary marking on these products and on engine. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. PERSONAL PRECAUTIONS a. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. b. Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery. c. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately. d. Never smoke or allow a spark or flame in vicinity of battery or engine. e. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical part that may cause explosion. When charging the internal battery, work in a well ventilated area and do not restrict ventilation in any way. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Do not expose a power pack to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion. The temperature of 130°C can be replaced by the temperature of 265°F. Read the following instructions to ensure safety before using. Improper use may result in fire, property damage or personal injury. INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. WARNING - When using this product, basic precautions should always be followed, including the following: 2 1. Do not charge the adapter via power supply systems that operate outside of AC100-240V. 2. Do not charge the unit via solar panel that operate voltage outside of DC12-26V. 3. Always use approved attachment charging cables. we take no responsibility for any damage caused by using other brand charging cable. 4. When charging, please place the product on the ground with no flammable or combustible materials around. To prevent accidents, never leave the machine unattended during charging. 5. Do not charge a product immediately after rated power output for longtime , because it maybe protected by the BMS. 6. DO NOT charge a product until it cools down to room temperature. 7. Once the unit is fully charged, unplug the adapt or charger. 8. Only charge, use the unit within an ambient temperature of 0 to 40 °C (32~104°F). 1. Please keep the product away from children's reach. If a child accidentally swallows certain parts, seek medical attention immediately. 2. If a warning of insufficient battery power appears, please charge the battery before storing. 3. Please store the product in a dry environment. Do not place the product where it may come into contact with water or other liquid. 4. Please ensure that no small metal objects fall on the product or around the product storage. Precautions for product charging Product storage and transportation Product maintenance 1. Do not store the product in an environment below -15°C or above 45°C. 2. If the battery is not used for a long time, the battery life may be shortened. 3. Fully charge and discharge at least once every 3 months to ensure battery life. Feature details Button feature 3 D B C A A: Power ON/OFF Button B: SOS mode & LED light Button C: DC Output Power ON/OFF Button D: USB Output Power ON/OFF Button E: AC Output Power ON/OFF Button E 1 2 3 4 5 6 8 10 13 7 9 11 12 Note: No user-serviceable parts inside. Recommended to fully charge the T-500 before use. 1 2 3 4 Cigarette lighter output LCD Screen display DC 5525 output USB-C output 5 USB-A output 6 7 8 AC output DC Input Photovoltaic input 9 SOS Mode & LED light 10 Anti-collision angle 13 11 Wireless charger Folding handle Air intake vent with cooling fan 12 4 Function buttons Button A: POWER ON/OFF Button A is the main switch. Press button A to turn on or off. Bu…

Text truncated - open the document above for the full version.

ShenZhenIntelligentEnergyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2022-03-23 Subject;RequestforConfidentiality FCCID:2A4UPT500MV1000 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:ZhuJiQuan Title:Manager

ShenZhenIntelligentEnergyCo.,Ltd LetterofAuthorization Company:ShenZhenIntelligentEnergyCo.,Ltd Address:No.3Building,Floor2,LilinIndustrialArea,GuanguangRoad, ShenzhenCity,China ProductName:PortablePowerStation ModelNumber:T500 Trademark:N/A FCCIdentifier:2A4UPT500MV1000 WeauthorizeMiCOMLabsInc,575BoulderCourt,Pleasanton,California94566, USA,toactonourbehalfonallmattersconcerningtheabovenamedequipment. AnyindividualwithinMiCOMLabsisauthorizedtoactonourbehalfandtake actionontheapplication. WedeclarethatMiCOMLabsInc,575BoulderCourt,Pleasanton,California 94566,USA,isallowedtoforwardallinformationrelatedtotheapprovalproject totheFederalCommunicationCommissionandtodiscussanyissues concerningtheapprovalapplication.AnyandallactscarriedoutbyMiCOMLabs onourbehalfshallhavethesameeffectasactsofourown. Name:ZhuJiQuanDate:23.03.2022 Signatureofapplicant:

ShenZhen Intelligent Energy Co., Ltd Company: ShenZhen Intelligent Energy Co., Ltd Address: No.3 Building, Floor 2, Lilin Industrial Area, Guanguang Road, Shenzhen City, China The EUT does comply with item 5.2 of KDB 680106 D01v03 as follows table Requirements of KDB 680106 D01 Yes/No Description (1) Power transfer frequency is less than 1 MHz Yes The EUT frequency range is: 112kHz- 205kHz (2) Output power from each primary coil is less than or equal to 15 watts. Yes The output power is less than 15W (3) The system may consist of more than one source primary coils, charging one or more clients. If more than one primary coil is present, the coil pairs may be powered on at the same time. Yes EUT has only one coil (4) Client device is placed directly in contact with the transmitter. Yes EUT can be directly charged (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes EUT is a mobile device (6) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the surface from all coils that by design can simultaneously transmit, and while those coils are simultaneously energized, are demonstrated to be less than 50% of the applicable MPE limit. Yes Fulfil requirements Name:Zhu Ji Quan Date: 23.03.2022 Signature of applicant:

209,90±0,01 119,90±0,01 PORTABLE POWER STATION Made in China UN38.3 株式会社成洋 Li-ion Type: T-500 Battery capacity: 22.2V,23.4 Ah 519.48Wh DC input: 12V~26V, (max. 8.5A &max. 105W ) PV input: 12V~26V, (max. 8.5A &max. 105W ) DC 5525 output ×2: 12V⎓5A(each), total 10 A Car outlet output: 12V⎓10A (DC 5525output (2) + caroutletoutput: total10A) USB-A output ×3: 5V⎓3.0A, 9V⎓2A, 12V⎓1.5A USB-C output: 5V/ 9V/12V/15V/20V⎓3A (max.60W ) Wireless charger: 9V⎓1.1 A (10W ) AC output ×2: pure sine wave 110V~60Hz, total 500W Discharging temperature: 5 to °F (-15 to 40°C)104 Charging temperature: 32 to 104°F (0 to 40°C) Date Code : 27/12/2021 Shenzhen Intelligent Energy Co.,Ltd. (Dongguan) Branch Serial Numher: Label WARNING! Do not short-circuit the unit. To avoid short-circuiting, keep the unit away from all metal objects (e.g.coins, hair-pins, keys, etc. ) . Do not heat the unit, or dispose of it in fire, water or other liquids. Keep away from high temperatures.Do not expose the unit to direct sunlight. Keep away from high humidity, dusty places. Do not disassemble or reassemble this unit. Do not drop and place heavy objects on, or allow strong impact to this unit. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. The unit may become hot when charging. This is normal. Be careful when handling. Use the unit properly to avoid electronic shock. The product is only used for emergency power station, it can not replace the standard DC or AC power of household appliances or digital products. Do not overcharge the internal battery. See Instruction Manual. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. AVERTISSEMENT! Ne court-circuitez pas l'appareil. Pour éviter tout court-circuit, éloignez l'appareil de tout objet mé tallique (par exemple, pièces de monnaie, épingles à cheveux, clés, etc.). Ne chauffez pas l'appareil et ne le jetez pas dans le feu, l'eau ou d'autres liquides. Tenir à l'écart des températures élevées. N'exposez pas l'appareil à la lumière directe du soleil. Tenir à l'écart des endroits humides et poussiéreux. Ne démontez pas et ne réassemblez pas cet appareil. Ne laissez pas tomber, ne placez pas d'objets lourds dessus et ne laissez pas de chocs violents sur cet appareil. Cet appareil n'est pas destiné à être utilisé par des personnes(y compris des enfants) ayant des capacités physiques, sensorielles ou mentales réduites, ou un manque d'expérience et de connaissances, à moins qu'elles n'aient reçu une supervision ou des instructions concernant. L'utilisation de l'appareil par une personne responsable de leur sécurité. Les enfants doivent être surveillés pour s'assurer qu'ils ne jouent pas avec l'appareil. L'appareil peut devenir chaud pendant la charge. C'est normal. Soyez prudent lors de la manipulation. Utilisez l'appareil correctement pour éviter les chocs électroniques. Le produit n'est utilisé que pour la centrale électrique de secours, il ne peut pas remplacer l'alimentation CC ou CA standard des appareils ménagers ou des produits numériques. Ne pas surcharger la batterie interne. Consulter le manuel d'utilisation. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID : 2A4UPT500MV1000 Label positions

ANT

ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. RFExposureEvaluation FCCID:2A4UPT500MV1000 MeasuringStandard FCCPart1(1.1310)andPart2(2.1091) KDB680106D01RFExposureWirelessChargingBaseAppv03 TestConfiguration ThetestdistanceisfromthecenteroftheprobetotheedgeoftheEUT. ThetestdistanceofPositionEonthefrontsideis20cm,thetestdistanceofPositionA,B,C,Dis15cmusing theequipmentlistabovefordeterminingcompliancewiththeMPErequirementsofFCCPart1.1310. TheRFpowerdensitywasmeasuredatUndermaximumloadtest. ThetestdistanceofPositionEonthefrontsideis20cm,thetestdistanceofPositionA,B,C,Dis15cm,the fieldprobeswerepositionedatthelocationwherethereismaximumfieldstrength.ThemaximumE-fieldand H-fieldisreportedbelow. Thisdeviceusesawirelesschargingcircuitforpowertransferoperatingatthefrequencyof112KHz-205kHz. Thus,the300kHzlimitswereused:E-fieldLimit=614(V/m);H-fieldlimit=1.63(A/m). TESTSetup ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. TESTLimits MeasurementUncertainty Thedataandresultsreferencedinthisdocumentaretrueandaccurate.Thereaderiscautionedthattheremaybe errorswithinthecalibrationlimitsoftheequipmentandfacilities.Themeasurementuncertaintywascalculatedfor allmeasurementslistedinthistestreportacc.toTR-100028-01”ElectromagneticcompatibilityandRadiospectrum Matters(ERM);Uncertaintiesinthemeasurementofmobileradioequipmentcharacteristics;Part1”and TR-100028-02“ElectromagneticcompatibilityandRadiospectrumMatters(ERM);Uncertaintiesinthemeasurement ofmobileradioequipmentcharacteristics;Part2“andisdocumentedintheKSIGNTestingCo.,Ltd.qualitysystem acc.toDINENISO/IEC17025.Furthermore,componentandprocessvariabilityofdevicessimilartothattested mayresultinadditionaldeviation.Themanufacturerhasthesoleresponsibilityofcontinuedcomplianceofthe device.BelowisthebestmeasurementcapabilityforKSIGNTestingCo.,Ltd. TestItemsMeasurementUncertaintyNotes Allemissions,radiated(<30M)(9kHz-30MHz)2.20dB(1) Note(1):Thisuncertaintyrepresentsanexpandeduncertaintyexpressedatapproximatelythe95%confidence levelusingacoveragefactorofk=1.96. ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. MeasuringDeviceandTestEquipment DescriptionManufacturerModelS/N Cal.Until ProbeFHP(1kHz-400kHz) NardaSafetyTest SolutionsGmbH EHP-50FJ-0015June10,2022 BroadbandFieldMeterNardaNBM-550Q201455Sep10,2022 PHONE1HUAWEIP40N/AN/A TESTMODE MODETESTMODEDESCRIPTION 1Wirelesschargingmode(Fullload) 2Wirelesschargingmode(Halfload) 3Wirelesschargingmode(Nullload) ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. TESTRESULT PassedNotApplicable EUTPortablePowerStationModelName.:T-500 Pressure:1010hPaTestDate:2022-03-20 TestVoltage:Output:10W(Max) E-FieldStrengthat15cmsurroundingtheEUTand20cmabovethetopsurfaceoftheEUT EUT Side Frequency Range (kHz) Probe A (V/m) Probe B (V/m) Probe C (V/m) Probe D (V/m) Probe E (V/m) Limits (V/m) Full load 112~2050.880.910.900.922.91 614 Half load 112~2050.840.860.870.892.88 Null load 112~2050.810.850.880.822.75 H-FieldStrengthat15cmsurroundingtheEUTand20cmabovethetopsurfaceoftheEUT EUT Side Frequency Range (kHz) Probe A (A/m) Probe B (A/m) Probe C (A/m) Probe D (A/m) Probe E (A/m) Limits (A/m) Full load 112~2050.530.570.560.580.73 1.63 Half load 112~2050.470.510.530.560.69 Null load 112~2050.430.500.450.550.67 Remark:ThedevicemeetsthemobileRFexposurelimitata15cmseparationdistanceasspecified in§2.1091oftheFCCRules Note:H-FieldStrengthlessthan50%oftheapplicableMPElimit. ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. PHOTOGRAPHSOFTESTSETUP PositionE PositionA ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. PositionB PositionC ShenzhenCTATestingTechnologyCo.,Ltd. Room106,Building1,YibaolaiIndustrialPark,QiaotouCommunity,Fuhai Street,Bao’anDistrict,Shenzhen,China ShenzhenCTATestingTechnologyCo.,Ltd. PositionD **********************EndofReport**********************

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn FCC PART 15 SUBPART C TEST REPORT Report Reference No. ..................... : FCC ID. ............................................ : CTA22030901501 2A4UPT500MV1000 Compiled by ( position+printed name+signature) .. : File administrators Kevin Liu Supervised by ( position+printed name+signature) .. : Project Engineer Kevin Liu Approved by ( position+printed name+signature) .. : RF Manager Eric Wang Date of issue ..................................... : Mar. 22, 2022 Representative Laboratory Name .: Shenzhen CTA Testing Technology Co., Ltd. Address ............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : ShenZhen Intelligent Energy Co., Ltd Address ............................................ : No.3 Building, Floor 2, Lilin Industrial Area, Guanguang Road, Shenzhen City, China Test specification ...........................: Standard ........................................... : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10: 2013 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purpses as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Portable Power Station Trade Mark ....................................... : N/A Manufacturer .................................... : ShenZhen Intelligent Energy Co.,Ltd (Dongguan) Branch Model/Type reference....................... : T-500 Listed Models .................................. : N/A Modulation Type ............................... : ASK Operation Frequency ........................ : From 112KHz~205KHz Rating ............................................... : Input:AC 110-240V 50/60Hz Output: Wireless Charging: 10W(Max) Result................................................ : PASS Report No.: CTA22030901501 Page 2 of 23 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : Portable Power Station Model /Type : T-500 Listed Models : N/A Model Declaration : N/A Applicant : ShenZhen Intelligent Energy Co., Ltd Address : No.3 Building, Floor 2, Lilin Industrial Area, Guanguang Road, Shenzhen City, China Manufacturer : ShenZhen Intelligent Energy Co.,Ltd (Dongguan) Branch Address : Building 1, Zone7, No.1 Longxi Road, Tangxia Town, Dongguan City, Guangdong Province, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA22030901501 Page 3 of 23 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 T E S T S T A N D A R D S ........................................................................ 4 2 S U M M A R Y ................................................................................... 5 2.1 General Remarks .......................................................................................................................................... 5 2.2 Product Description ..................................................................................................................................... 5 2.3 Description of the test mode ....................................................................................................................... 5 2.4 Special Accessories ..................................................................................................................................... 5 2.5 Modifications ................................................................................................................................................ 5 3 T E S T E N V I R O N M E N T .................................................................... 6 3.1 Address of the test laboratory .................................................................................................................... 6 3.2 Test Facility ................................................................................................................................................... 6 3.3 Environmental conditions ........................................................................................................................... 6 3.4 Summary of measurement results ............................................................................................................. 7 3.5 Statement of the measurement uncertainty .............................................................................................. 7 3.6 Equipments Used during the Test .............................................................................................................. 8 4 T E S T C O N D I T I O N S A N D R E S U L T S ................................................... 9 4.1 AC Power Conducted Emission ........................................…

Text truncated - open the document above for the full version.