2A6KA-AB202TRIPOD SELFIE STICK

oth-AB202 Mannual Power on: Press and hold the button for 2 seconds to power on, the green indicator light stays on for 3 seconds and then enters the pairing state, the pairing state green indicator flashes for 1 second/time. Pairing connection: Turn on the device and enter the pairing state, use the Bluetooth device to search for the Bluetooth name "SEAJIC", and click to connect. Taking pictures/videos: After the mobile phone enters the camera interface, short press the button to take a picture; after the mobile phone enters the video recording interface, short press the button to take a video. Power off： In the power-on and sleep state, press and hold the camera button for 3 seconds to turn off the power, and the indicator light will turn off. Charging：During the charging process, the red indicator light is always on, and automatically turns off when fully charged. The charging current is 50MA. 1 Automatic shutdown after charging: 2 Low voltage indication：When the battery is low (less than or equal to 3.4V), the red indicator light will automatically start flashing until it starts charging. 3 low power shutdown：When the battery voltage is lower than 3.0V, the remote control automatically shuts down. Button MICRO USB connector Electrical parameters Power on current ＜18mA momentary peak pairing current 0.5mA – 5mA pairing status stand-by current 0.5mA–1.5mA connection without working Working current 0.5mA – 2.5mA When pressing the key continuously Power off current 小于5uA Power off status Main configuration: Bluetooth chip TLSR8232 crystal oscillator 24MHZ,3.2X2.5mm EEPROMM built-in Button 5*5*1.5mm Battery capaity 50MAh Bluetooth distance ≤10 meter Dimensions Safety precautions: This product contains a built-in battery. It is not suitable to expose the product to strong sunlight or fire or Water spray . Do not place the device in an environment where the temperature is too high (more than 50 degrees Celsius) because This can cause serious damage to the equipment. FCC Regulatory Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Thank you for using this product, I wish you a happy life.

Dongguan OSM Digital Co., Ltd Date: 05/16/2022 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2A6KA-AB202 To whom it may concern: We, the undersigned, hereby authorize Compliance Certification Services (Kunshan) Inc and Kidd Yang in Compliance Certification Services (Kunshan) Inc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own.. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Dongguan OSM Digital Co., Ltd This authorization is valid until further written notice from the applicant. Print Name: Anmy cheng Title: Purchase Signature: On behalf of Company: Dongguan OSM Digital Co., Ltd Telephone: 0769-38820219 E-mail: [email protected]

Dongguan OSM Digital Co., Ltd Date: 05/16/2022 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 From: Beyerdynamic Regarding: Confidentiality Request regarding application for FCC ID: 2A6KA-AB202 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby requests confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY（Remark：如下资料需要短期保密请选择天数0，45,90或者180天，短期保密期间产品不能在美国市场上售卖。Additionally, the applicant requests the following documents be held confidential until the device is marketed or 0 days from the grant date, whichever is less. If the device is marketed within 0 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. Delete any document that is NOT included in your application External Photos Internal Photos Test Setup Photos User manual(s) Print Name: Anmy cheng Title: Purchase Signature: On behalf of Company: Dongguan OSM Digital Co., Ltd Telephone: 0769-38820219 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Dongguan OSM Digital Co., Ltd Address 501, Building 2, No.6 Tiansha Road Keyuan City Tangxia Town Dong guan Ctiy, China Grantee Code 2A6KA FCC ID 2A6KA-AB202 Authorized Contact Name Anmy Cheng Contact Email [email protected] Contact Phone 0769-38820219 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 2022/05/17 Print Name: Anmy cheng Title: Purchase *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 5 External Photos for FYCR2204000091AT FCC ID: 2A6KA-AB202 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 5 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 3 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 4 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 5 of 5

四周居中 背面正面 31.2mm 7.8mm FCC ID: 2A6KA-AB202 215-JUK024 Model No: Oth-AB202Product name: Tripod Selfie Stick FCC ID: 2A6KA-AB202 215-JUK024 Model No: Oth-AB202 Product name: Tripod Selfie Stick

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 5 Internal Photos for FYCR2204000091AT FCC ID: 2A6KA-AB202 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 5 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 3 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 4 of 5 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 5 of 5

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009103 Page: 1 of 10 Kidd Yang EMC Laboratory Manager 1 Cover Page RF Exposure Report Application No.: FYCR2204000091AT Applicant: Dongguan OSM Digital Co., Ltd Address of Applicant: 501, Building 2, No.6 Tiansha Road, Keyuan City, Tangxia Town, Dong guan City Manufacturer: Dongguan OSM Digital Co., Ltd Address of Manufacturer: 501, Building 2, No.6 Tiansha Road, Keyuan City, Tangxia Town, Dong guan City Factory: Dongguan OSM Digital Co., Ltd Address of Factory: 501, Building 2, No.6 Tiansha Road, Keyuan City, Tangxia Town, Dong guan City Equipment Under Test (EUT): EUT Name: TRIPOD SELFIE STICK Model No.: Oth-AB202, Oth-AB202B/Oth-AB202PRO, Oth-AB202M B0057, Ailun Selfie Tripod 01   Please refer to section 3 of this report which indicates which model was actual tested and which were electrically identical. FCC ID: 2A6KA-AB202 Standard(s) : FCC Rules 47 CFR §2.1093 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2022-04-21 Date of Test: 2022-04-25 to 2022-05-11 Date of Issue: 2022-05-13 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009103 Page: 2 of 10 Revision Record Version Chapter Date Modifier Remark 01 2022-05-13 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009103 Page: 3 of 10 2 Contents Page 1 COVER PAGE .................................................................................................................................... 1 2 CONTENTS ........................................................................................................................................ 3 3 GENERAL INFORMATION ................................................................................................................ 4 3.1 GENERAL DESCRIPTION OF E.U.T. ................................................................................................ 4 3.2 DETAILS OF E.U.T. ....................................................................................................................... 4 3.3 SEPARATION DISTANCE ................................................................................................................ 5 3.4 TEST LOCATION ............................................................................................................................ 5 3.5 TEST FACILITY .............................................................................................................................. 5 4 FCC RADIOFREQUENCY RADIATION EXPOSURE LIMITS .......................................................... 6 4.1 BLANKET 1 MW BLANKET EXEMPTION ........................................................................................... 6 4.2 MPE-BASED EXEMPTION .............................................................................................................. 6 4.3 SAR-BASED EXEMPTION ............................................................................................................... 7 5 MEASUREMENT AND CALCULATION .......................................................................................... 10 5.1 MAXIMUM TRANSMIT POWER ....................................................................................................... 10 5.2 RF EXPOSURE CALCULATION ...................................................................................................... 10 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009103 Page: 4 of 10 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. Power supply: Lithium Ion Battery: 3.7V 50mAh rechargeable battery which charged by USB port Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V4.2 LE Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: PCB Antenna Antenna Gain: 2.3dBi Declaration of EUT Family Grouping: Model No.: Oth-AB202, Oth-AB202B/Oth-AB202PRO, Oth-AB202M B0057, Ailun Selfie Tripod 01 Only the model Oth-AB202 was tested, since according to the declaration from the applicant, the electrical circuit design, PCB layout, components used and internal wiring and functions were identical for the above models, with only difference on appearance and model No.. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009103 Page: 5 of 10 3.3 Separation Distance Minimum test separation distance: 5mm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. 3.4 Test Location All tests were performed at: Compliance Certification Services（Kunshan）Inc. Shenzhen branch. Fuyong lab. Xinlong TechnoPark,Fengtang Road, Fuyong Subdistrict, Bao’an, Shenzhen, China Tel: +86 755 8866 3988 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 6606.01) Compliance Certification Services（Kunshan）Inc. Shenzhen branch is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 6606.01. • FCC –Designation Number: CN1322 Compliance Certification Services（Kunshan）Inc. Shenzhen branch has been recognized as an accredited testing laboratory. Designation Number: CN1322. Test Firm Registration Number: 718073 • Innovation, Science and Economic Development Canada Compliance Certification Services（Kunshan）Inc. Shenzhen branch has been recognized by ISED as an accredited te…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009102 Page: 1 of 59 Kidd Yang EMC Laboratory Manager TEST REPORT Application No.: FYCR2204000091AT Applicant: Dongguan OSM Digital Co., Ltd Address of Applicant: 501, Building 2, No.6 Tiansha Road, Keyuan City, Tangxia Town, Dong guan City Manufacturer: Dongguan OSM Digital Co., Ltd Address of Manufacturer: 501, Building 2, No.6 Tiansha Road, Keyuan City, Tangxia Town, Dong guan City Factory: Dongguan OSM Digital Co., Ltd Address of Factory: 501, Building 2, No.6 Tiansha Road, Keyuan City, Tangxia Town, Dong guan City Equipment Under Test (EUT): EUT Name: TRIPOD SELFIE STICK Model No.: Oth-AB202, Oth-AB202B/Oth-AB202PRO, Oth-AB202M B0057, Ailun Selfie Tripod 01 ♣ ♣ Please refer to section 2 of this report which indicates which model was actual tested and which were electrically identical. FCC ID: 2A6KA-AB202 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2022-04-21 Date of Test: 2022-04-25 to 2022-05-11 Date of Issue: 2022-05-13 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009102 Page: 2 of 59 Revision Record Version Chapter Date Modifier Remark 01 2022-05-13 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009102 Page: 3 of 59 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Declaration of EUT Family Grouping: Model No.: Oth-AB202, Oth-AB202B/Oth-AB202PRO, Oth-AB202M B0057, Ailun Selfie Tripod 01 Only the model Oth-AB202 was tested, since according to the declaration from the applicant, the electrical circuit design, PCB layout, components used and internal wiring and functions were identical for the above models, with only difference on appearance and model No.. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220400009102 Page: 4 of 59 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................. 6 4.1 DETAILS OF E.U.T. ......................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 6 4.4 TEST LOCATION ............................................................................................................................. 7 4.5 TEST FACILITY ............................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 7 5 EQUIPMENT LIST ............................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................14 6.1 ANTENNA REQUIREMENT ................................................................................................................14 6.1.1 Test Requirement: ..................................................................................................................14 6.1.2 Conclusion ..............................................................................................................................14 7 RADIO SPECTRUM MATTER TEST RESULTS .................................................................................15 7.1 CONDUCTED PEAK OUTPUT POWER ................................................................................................15 7.1.1 E.U.T. Operation .....................................................................................................................15 7.1.2 Test Mode Description ................................................................................................…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 3 Setup Photos for FYCR2204000091AT FCC ID: 2A6KA-AB202 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 3 Test Setup Photos Radiated Emissions which fall in the restricted bands Radiated Spurious Emissions Below 1GHz Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 3 of 3 Radiated Spurious Emissions Above 1GHz