2A6X2-880TSM Ghost Embedded Radio

January 30, 2026 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada ATTN.: Reviewing Engineer Subject: Covered Equipment Certification Attestation Letter Applicant: TrellisWare Technologies FCC ID: 2A6X2-880 The applicant certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section §2.903 of the FCC rules. This includes certifying that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current FCC Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. The applicant certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Applicant Signed: Signed: Mike Rudeen Printed name: Mike Rudeen Title: Project Engineer Company Name: TrellisWare Technologies Inc.

Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Appointment of Agent for FCC and ISED Certification Application Dear Director of Certification, This letter formally appoints Spencer Zhong of Nemko Canada, Inc. located at 303 River Road, Ottawa, Ontario, Canada K1V 1H2, as our authorized agent to represent us in the application process for equipment certification. We confirm that the submitted documents accurately depict the device or system seeking certification. Additionally, we guarantee that all units produced, imported, or marketed, as defined by FCC and ISED Canada regulations, will possess a label identical to the one submitted with this application. By signing below, we certify that neither our company nor any party involved in the application is subject to denial of federal benefits, including FCC benefits, as outlined in Section 5301 of the Anti-Drug Abuse Act of 1988 (21 U.S.C. §862) due to a conviction for possession or distribution of a controlled substance. Furthermore, no party involved in the application, as defined in 47 CFR 1.2002 (b), is subject to denial of federal benefits, including FCC benefits. We attest to the truth and accuracy of the information provided to the FCC to the best of our knowledge (47 CFR 2.911 (d)) and acknowledge our responsibilities as a grantee regarding certified equipment (47 CFR 2.909). In instances where our authorized agent signs the application for certification on our behalf, we understand that Nemko North America, Inc. remains solely responsible for adhering to the terms and conditions for certification as specified by Nemko Canada Inc. Sincerely, Dated: January 30, 2026 Agency agreement expiration date: January 30, 2027 *Up to 12 months Signed by: Mike Rudeen Print name: Mike Rudeen Title: Project Engineer Phone: (858) 482-3839 On behalf of: Company name: TrellisWare Technologies Inc.

1 NON-DISCLOSURE AGREEMENT Non-Disclosure Agreement # CON-001344-N Parties and Points of Contact: Name: TrellisWare Technologies, Inc. (“TrellisWare”) Name: XYZ (“Company”) Address: 10641 Scripps Summit Court, Suite Address: 100 City/St/Zip: San Diego, CA 92131 Agreement POC: Email: Phone: PI POC: Email: Phone: City/St/Zip: Agreement POC: Email: Phone: PI POC: Email: Phone: THIS NON-DISCLOSURE AGREEMENT (the "Agreement") is made and entered into by and between TrellisWare and Company to protect certain proprietary and confidential information of TrellisWare or of Company which may be disclosed under this Agreement solely for the Purpose (as defined below). In consideration of the mutual promises contained herein and for other good and valuable consideration, the receipt and sufficiency of which are hereby acknowledged, TrellisWare and Company agree as follows: 1. THE PARTIES TrellisWare and Company shall each be referred to herein as a “Party” or collectively as the “Parties.” A Party disclosing information under this Agreement shall be referred to as the “Disclosing Party.” A Party receiving information under this Agreement shall be referred to as the “Receiving Party.” 2. PURPOSE (A) The purpose of this Agreement is to enable the Parties to exchange proprietary financial, business, and/or technical data (possibly including, but not limited to designs, processes, performance specifics and other sensitive data) relating to [insert purpose] to support discussions concerning an actual or contemplated business relationship between the Parties (hereinafter referred to as the “Purpose”). 3. PROPRIETARY INFORMATION (“Proprietary Information”) (A) For purposes of this Agreement, the term “Proprietary Information” shall mean all information disclosed hereunder by the Disclosing Party to the Receiving Party, which is marked as “Proprietary”, “Confidential” or a similar marking. Proprietary Information shall also include information disclosed orally or visually, provided: (i) the information is identified as confidential or proprietary at the time of disclosure, (ii) a written summary of the disclosed information is delivered by the Disclosing Party to the Receiving Party within twenty (20) calendar days after the initial disclosure, and (iii) the written summary is marked as “Proprietary”, “Confidential” or a similar marking. For the avoidance of doubt, during such twenty (20) day period, the Receiving Party shall treat all information disclosed orally or visually as Proprietary Information in accordance with the terms of this Agreement. (B) Notwithstanding the foregoing, Proprietary Information shall not include information which the Receiving Party can demonstrate by reasonable evidence: (i) is publicly available prior to the Effective Date (as defined below) or becomes publicly available after the Effective Date through no breach of this Agreement or other act or omission by the Receiving Party or any individual or entity to whom the Receiving Party discloses such information in accordance with the terms of this Agreement; (ii) is already in the possession of the Receiving Party on a non- confidential basis at the time of disclosure by the Disclosing Party; (iii) is obtained by the Receiving Party from a third party which, to the best of the Receiving Party's knowledge, was free to disclose REF0000031, Rev B Revision Date: 9/18/2019 TrellisWare Proprietary Information Page 1 of 6 2 such information without restriction, unless the Receiving Party is notified by the Disclosing Party of misappropriation by said third party promptly after the Disclosing Party knew of such misappropriation; (iv) is independently developed by or for the Receiving Party without use of or reference to the Disclosing Party’s Proprietary Information, as shown by documents and other competent evidence in the Receiving Party’s possession; or (v) is approved for release in writing by the Disclosing Party. (C) Notwithstanding anything to the contrary herein, if the Disclosing Party discloses any Proprietary Information hereunder that is subject to a security classification by the U.S. Government, the Disclosing Party shall identify such classification at the time of disclosure and the Parties agree to handle such Proprietary Information in accordance with applicable U.S. Government requirements. (D) Notwithstanding anything to the contrary herein and subject to the requirements and exceptions stated below, if the purpose of this Agreement encompasses the submission of a proposal to a third party, then a Receiving Party submitting such proposal may disclose any Proprietary Information disclosed to it under this Agreement to such third party to the extent that such Receiving Party includes the Proprietary Information in the contemplated proposal, with the prior written consent of the Disclosing Party. The Disclosing Party may constrain the use or disclosure of its Proprietary Information pursuant to this Section 3(D) by providing written instruction to the Receiving Party. Any such disclosure pursuant to this Section 3(D) shall require that the Proprietary Information be indicated as such with its original “Proprietary”, “Confidential” or similar markings, to the extent practical, and with any other restrictive legends necessary to preserve its confidentiality as specified by U.S. Government regulation or the regulations or procedures of any other customer, as applicable. Notwithstanding anything to the contrary herein or the termination of this Agreement, the Receiving Party may retain the Proprietary Information included in such proposal, as described in this Section 3(D), in accordance with its record keeping policies and subject to a continuing obligation to protect the Proprietary Information in accordance with Section 4 of this Agreement. 4. CONFIDENTIALITY OBLIGATIONS (A) Receiving Party Responsibilities. With respect to Proprietary Information transmitted hereunder, unless otherwise provided in this Agreement, the Rec…

Text truncated - open the document above for the full version.

January 30, 2026 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: 2A6X2-880, Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. We request the exhibits selected below as long term confidential (LTC) be withheld from public view permanently: Selection of exhibits for LTC - general Exhibit name ☒ Permanent (Long Term) Block Diagrams ☒ Permanent (Long Term) Operation Description / Theory of Operation ☒ Permanent (Long Term) Parts List & Placement / BOM ☒ Permanent (Long Term) Schematics ☒ Permanent (Long Term) Internal photos* ☒ Permanent (Long Term) User Guide** Selection of exhibits for LTC - specific 1 Exhibit name ☐ Permanent (Long Term) Tune-Up Procedure ☐ Permanent (Long Term) SDR 2 Software / Security Info The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed: Mike Rudeen Printed name: Mike Rudeen Title: Project Engineer Phone: 858-229-6369 Company Name: TrellisWare Technologies Inc. Address: 10641 Scripps Summit Ct #100, San Diego, CA 92131, United States 1 - Tune up procedure is applicable only for licensed equipment. 2 - The FCC rules require that any radio, in which the software is designed or expected to be modified by a party other than the manufacturer that would affect the operating parameters of frequency range, modulation type, maximum output power or other radio frequency parameters outside the range under which the transmitter has been approved in accordance with the FCC rules, must be certified as a software-defined radio (SDR).

January 30, 2026 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Request for Special Confidentiality – FCC FCC ID: 2A6X2-880 Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. We request the exhibits selected below as long term confidential (LTC) be withheld from public view permanently: Selection 1 Exhibit name ☒ User’s Manual ☒ Internal Photos Our user manual contains proprietary technical content intended exclusively for professional technicians operating under a Non-Disclosure Agreement (NDA). Distribution or sale of the manual must be contingent upon the recipient’s agreement to an NDA that strictly prohibits the disclosure of its contents. Furthermore, the device’s internal circuitry and components are not accessible to end users and are designed to be serviced solely by authorized technicians under NDA. All product sales must be governed by an NDA that protects proprietary information, including internal photographs. A sample NDA is included with this application. Our company has made substantial investments in the development of this innovative product, which represents a first-of-its-kind solution in the industry. Public disclosure of the technical details would compromise our competitive edge and could result in significant financial harm. Safeguarding the confidentiality of our design is critical to protecting our intellectual property. The information provided includes trade secrets and proprietary data not customarily disclosed to the public. Unauthorized disclosure could adversely impact our business and provide competitors with an unfair advantage. Sincerely, Signed: Mike Rudeen Printed name: Mike Rudeen Title: Project Engineer Phone: 858-229-6369 Company Name: TrellisWare Technologies Inc. Address: 10641 Scripps Summit Ct #100, San Diego, CA 92131, United States 1 - These items require further information to be provided to TCB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and review section II, 3) regarding specific information (NDA) that must accompany these requests.

Dated: 18 February 2026 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Single Modular Modular Approval FCC ID: 2A6X2-880 The following attestation addresses the requirements to support modular approval: Modular approval requirement Yes (provide brief statement) No * (1) The radio elements must have its own radio frequency circuitry shielded. The physical crystal and tuning capacitor(s) may be located external to the shield, but must be on the module assembly Yes, The module contains a metal shield which covers all RF components and circuitry. – (2) The module must have buffered modulation/data inputs (if provided) to ensure that the device will comply with FCC requirements under conditions of excessive data rates or over-modulation. Yes, data to the modulation circuit is buffered as described in the operational description provided with the application – (3) The module must contain its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. Yes, the module contains its own power supply regulation. Please refer to schematic filed with this application – (4) The module must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a ‘‘unique’’ antenna coupler (at all connections between the module and the antenna, including the cable). The ‘‘professional installation’’ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv) Yes, the module connects to its antenna using an SMP connector which is considered a non-standard connector. A list of antennas tested and approved with this device may be found in user’s manual provided with the application – (5) The module must demonstrate compliance in a stand-alone configuration, the module must not be inside another device during testing. This is intended to demonstrate that the module can comply with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, the module was tested stand- alone as shown in test setup photographs filed with this application – (6) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements) Yes, there is a label on the module as shown in the labeling exhibit filed with this application. Host specific labeling instructions are shown in the installation manual filed with this – application. (7) The module must comply with all specific rule or operating requirements applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. A copy of these instructions must be included in the application for equipment authorization. Yes, the module complies with FCC Part 15C requirements. Instructions to the OEM installer are provided in the installation manual filed with this application – (8) The module must comply with any applicable RF exposure requirements Yes, the module meets Mobile exclusion levels as shown in the RF exposure information filed with this application. – Sincerly, Signed: Mike Rudeen Printed name: Mike Rudeen Title: Project Engineer Phone: 858-753-1600 Company Name: TrellisWare Technologies Inc. Address: 10641 Scripps Summit Ct #100, San Diego, CA 92131, United States

FCC 15.203 Declaration Letter to Clarify the connector type Product: Modular Radio (Model TW-880, HVIN TW-880) FCC ID: 2A6X2-880 IC / ISED ID: 28565-880 Attestation Date: March 4, 2026 1. Applicability of Section 15.203 This device employs a standard female SMP connector that is externally accessible. Under normal consumer operation, Section 15.203 prohibits such user-accessible standard connectors. However, the professional-installation exemption in KDB 353028 D01 §II.A.2.c is invoked because: • The equipment is sold exclusively to trained personnel, military or authorized agencies, not to the general public. • Installation, calibration, and antenna attachment must be performed by trained professionals contracted by the licensee. • Users are explicitly prohibited from changing the antenna; the connector is only accessible by trained service personnel. 2. Professional Installation Justification Per KDB 353028 D01 guidance, justify as follows: 1. Controlled distribution o The radio module is not sold via retail or mail-order; it is issued exclusively through authorised channels to military or trained agency personnel. 2. Sophisticated installation requirements o Installation includes verifying field strength, configuring power levels, applying antenna- specific calibration, and ensuring RF exposure compliance in mission-specific configurations—tasks that require technical training and are not performed by end users. 3. Connector access limitation o Although externally located, the connector is ruggedized and access for user swap-out is prohibited by the user manual and physical design to prevent unauthorized antenna attachment. 3. Compliance Measures To meet KDB 353028 and §15.203: • Exhibit list of approved antennas including part numbers, vendor, type, maximum gain, feed-line specs, and matching cable length (only these antennas may be used). • Manual statement: “This device must be professionally installed. Unauthorized antenna attachment or connector access by end users is strictly prohibited.” 4. Grant Condition Statement (FCC Label/User Manual) The following verbiage is stated in the user manual: “This device must be professionally installed. Only approved antennas listed in this manual are permitted. End-users must not disconnect or replace the antenna connector.” Summary Table Requirement Compliance via Declaration FCC §15.203 standard connector Exempted via professional-installation justification KDB 353028 D01 guidance Met through controlled distribution, training requirements, connector access limitations Approved Antenna Listing required Exhibit included listing allowed antennas User/manual statement required Included clear prohibition on end-user antenna change Sincerely, Dated: March 4, 2026 Signed by: Print name: Mike Rudeen Mike Rudeen Title: Project Engineer Phone: (858) 753-1600 On behalf of: Company name: TrellisWare Technologies Inc.

External Photographs of the TrellisWare TW-880 Radio Marketing Name: TW-880 HVIN: ASY0750352

Label Design and Location Model (HVIN): ASY0750352 Name (PMN): TW-880

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The test results included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. FCC and ISED RSS-102– MPE Calculation; Date: January 2026 RF Exposure Compliance – MPE Calculation Report C h o o s e S c a n d i n a v i a n t r u s t Applicant company: TrellisWare Technologies Model number (HVIN): ASY0750352 Model name (PMN): TW-880 FCC Identification: FCC ID: 2A6X2-880 ISED certification number: IC: 28565-880 Product type: Mobile or Fixed Device Device category Professional Device for Occupational/Controlled Exposure Date of issue: March 4, 2026 Compliance Specifications: FCC 47 CFR Part 1 Subpart I, §§1.1307, 1.1310 FCC 47 CFR Part 2 Subpart J, §§2.1091, 2.1093 FCC KDB 447498 D01 General RF Exposure Guidance v06 FCC KDB 865664 D01 RF Exposure Procedures and Equipment Authorization Policies ISED Canada RSS-102 Issue 6 December 15, 2023 MPE calculation report Product info: FCC ID: 2A6X2-880 IC: 28565-880 Model: TW-880 Page 2 of 7 Test locations of Nemko Canada Inc. Ottawa site Montréal site GTA Cambridge site Facility address 303 River Road Ottawa, Ontario Canada K1V 1H2 Tel: +1 613 737 9680 Fax: +1 613 737 9691 292 Labrosse Avenue Pointe-Claire, Québec Canada H9R 5L8 Tel: +1 514 694 2684 Fax: +1 514 694 3528 1-130 Saltsman Drive Cambridge, Ontario Canada N3E 0B2 Tel: +1 519 650 4811 Test site identifier - FCC CA2040 CA2041 CA0101 Test site identifier – ISED Canada 2040A-4 2040G-5 24676 ANAB File Number AT-3195 AT-3193 AT-3194 Andrey Adelberg Senior EMC/Wireless Specialist Prepared by Signature Limits of responsibility The results presented in this report apply solely to the specific device model tested and are valid only for the operating conditions and installation requirements specified herein. Testing was conducted in accordance with ISO/IEC 17025:2017 requirements, and all results fall within the scope of Nemko Canada's accreditation. This MPE evaluation is based on the maximum power levels and operating conditions specified. Any modifications to the device hardware, software, or installation that could affect RF output power or antenna characteristics may invalidate this compliance demonstration. Copyright notification This report may be reproduced by the applicant in its entirety for regulatory submission and internal use. Any use of this report by third parties, including reliance on its contents or decisions made based on it, is solely at the risk of those third parties. Nemko Canada Inc. assumes no responsibility for any damages incurred by third parties as a result of actions taken based on this report. © Nemko Canada Inc. All rights reserved. MPE calculation report Product info: FCC ID: 2A6X2-880 IC: 28565-880 Model: TW-880 Page 3 of 7 1. Executive Summary This report presents the Maximum Permissible Exposure (MPE) analysis to demonstrate compliance with FCC and ISED RF exposure requirements. The evaluation considers both single transmitter operation and simultaneous multi-transmitter scenarios where applicable. 2. Key Findings Compliance status Complies Critical separation distances 20 cm Special conditions or limitations N/A MPE calculation report Product info: FCC ID: 2A6X2-880 IC: 28565-880 Model: TW-880 Page 4 of 7 MPE calculations for simultaneous transmission Device Classification Requirements Portable Device Definition (§2.1093) Devices designed for use by a person where the radiating structure is within 20 cm of the user's body require SAR evaluation rather than MPE calculation. Mobile Device Definition Devices installed in vehicles or with permanently installed antennas may use MPE calculations if minimum separation distances can be established. Fixed/Base Station Definition Stationary transmitters with controlled access to antenna locations may use MPE calculations for both occupational and general population exposure scenarios. 3. References, definitions and limits for FCC FCC §2.1091(d) (2) For operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in Table 1 in paragraph (e)(1) of this section, may be used instead of whole-body SAR limits as set forth in paragraphs (a) through (c) of this section to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b) of this part, except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. Table 1: §1.1310(e)(1)—Power Density Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3–3.0 *(100) ≤6 3.0–30 *(900 / f 2 ) <6 30–300 1.0 <6 300–1500 f / 300 <6 1500–100000 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3–1.34 *(100) <30 1.34–30 *(180 / f 2 ) <30 30–300 0.2 <30 300–1500 f / 1500 <30 1500–100000 1.0 <30 Notes: f = frequency in MHz. * = Plane-wave equivalent power density. MPE calculation report Product info: FCC ID: 2A6X2-880 IC: 28565-880 Model: TW-880 Page 5 of 7 4. References, definitions and limits for ISED RSS-102 Section 5.3.2 The power density reference levels, and associated reference period for devices employed by the general public (uncontrolled environment) and controlled-use devices (controlled environment) are specified in table below. Note that the power density limits specified in this table apply to whole body exposure conditions. Table 2: RSS-102— Power density limits Frequency range (MHz) Power density (W/m 2 ) Power density (mW/cm 2 ) Reference Period (minutes) Limits for controlled-use devices (controlled environment) 10–20 10 1 6 20–48 44.72 / ƒ 0.5 4.472 / ƒ 0.5 6 48–100 6.455 0.6455 6 100–6000 0.6455 ƒ 0.5 0.06455 ƒ 0…

Text truncated - open the document above for the full version.

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The tests included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. ANAB File Number: AT-3195 (Ottawa); AT-3193 (Pointe-Claire); AT-3194 (Cambridge) FCC 15.247 and RSS-247; Date: October 21, 2025 C h o o s e S c a n d i n a v i a n t r u s t RADIO TEST REPORT Report ID: Project number: REP124673 PRJ0088969 Type of assessment: Final product testing Type of radio equipment: Spread Spectrum/Digital Device (902–928 MHz) Spread Spectrum/Digital Device (2400–2483.5 MHz) Equipment class: DTS - digital transmission systems Applicant: Model name (PMN) TrellisWare Technologies, Inc TW-880 Description of product: Model number (HVIN): TSM Ghost Embedded Radio ASY0750352 FCC identifier: ISED certification number: FCC ID: 2A6X2-880 IC: 28565-880 Specifications:  FCC 47 CFR Part 15 Subpart C, §15.247  RSS-247, Issue 4, July 2025, Section 6 Date of issue: March 4, 2026 Sagarkumar Patel, EMC/RF Specialist Tested by Signature Andrey Adelberg, Senior EMC/RF Specialist Reviewed by Signature Report reference ID: REP124673 Page 2 of 69 Lab locations Company name Nemko Canada Inc. Facilities Ottawa site: 303 River Road, Ottawa, ON, Canada, K1V 1H2 Tel: +1 613 737 9680 Test site registration number: CA2040 Montréal site: 292 Labrosse Avenue, Pointe-Claire, QC, Canada, H9R 5L8 Tel: +1 514 694 2684 Test site registration number: CA2041 Cambridge site: 1-130 Saltsman Drive, Cambridge, ON, Canada, N3E 0B2 Tel: +1 519 650 4811 Test site registration number: CA0101 Website www.nemko.com Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contained in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: REP124673 Page 3 of 69 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Report summary ................................................................................................................................................................................. 4 1.1 Test specifications .................................................................................................................................................................................................... 4 1.2 Test methods ............................................................................................................................................................................................................ 4 1.3 Exclusions ..............................................................…

Text truncated - open the document above for the full version.