2A7IM-SBG01ProRig

ISED Statement This device complies with Innovation, Science and Economic Development licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference; and (2)this device must accept any interference. Including interference that may cause undesired operation of the device. Avis Innovation, Science et développement économique Le présent appareil est conforme aux Innovation, Science et développement économique aux appareils radio exem pt s de licence L'exploitation est autorisée aux deux conditions suivantes: 1)I'appareil ne doit pas produire de brouillage; et 2)I'utillsateur de I'appareil doit accepterbrouillage radioélectrique subi meme si le brouillage est susceptible d'encompromettre le fonctionnement. mauvais fonctionnement de I'appareil. Radiation Exposure Statement: This product complies with the ISED RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as desc ribed in this manual. Déclaration d'exposition aux radiations: Ce produit est conforme à la limite d'exposition ISED RF définie pour un environnement non contrôlé et est sûr pour le fonctionnement prévu comme décrit dans ce manuel. FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules ProRig S-BG01 . Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device mus t accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency ene rgy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer ence by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the part responsib le for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

TCB CALL página 1 File FCC ID: 2A7IM-S-BG01 Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○ We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. On the official register from : https://opencorporates.com/companies/us_il/LLC_12842678 In google: TCB CALL página 2 Bank information TCB CALL página 3 ► CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "C5266091_X23_Ed1_US_Agent_Letter" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "C5266091_X23_Ed1_US_Agent_Letter" >

1/1 FCC US Agent, LLC US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Telephone No: 708-571-3148 Email: [email protected] Applicant: Company name: ShiftCam Limited Product Description: ProRig Grantee code: 2A7IM FCC ID: 2A7IM-SBG01 FRN： 0032565525 Contact Name: Benson Chiu Address: Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Telephone No: (852)26200660 Email: [email protected] [ShiftCam Limited] certifies that, as of the date of this filing of the application with the TCB, [FCC US Agent, LLC] is our designated US agent for service of process for the above referenced FCC ID. [ShiftCam Limited] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2026/08/06 Applicant’s Name: Benson Chiu US Agent’s Name: Tim Payne Title: General Manager Title: Manager Signature Signature

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: ShiftCam Limited Grantee code: 2A7IM FCC ID: 2A7IM-SBG01 FRN: 0032565525 Contact Name: Benson Chiu Address: Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Telephone No: (852)26200660 Fax No: (852)26200660 Email: [email protected] i. [ShiftCam Limited] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [ ShiftCam Limited] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [ ShiftCam Limited] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment . Date: 08/06/2026 Applicant’s Name: Benson Chiu Title: General Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

ShiftCam Limited Code 00018768 Ed. 1 Item 1. The device is able to install software/program installation? ☐Yes, go to Item 2. ☒No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A Device ProRig Company name ShiftCam Limited Grantee code 2A7IM FCC ID 2A7IM-S-BG01 FRN 0032565525 Contact name Benson Chiu Address Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Telephone number (852)26200660 E-mail [email protected] Chipset/module information AC6323A Operating System (if applicable) N/A Storage Capacity (hard drive or other permanent memory storage, if applicable) N/A 2 # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A 3 # General Requirements (For Linux system) Yes / No or N/A Comments 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher 3 RAM: 1 GB 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐Yes, go to Item 3. ☒No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software Item 3. Connectivity Capabilities: N/ A N/ A N/A 4 # Physical Interface Purpose Justification 1 1 # Wireless Interface Purpose Justification 1 1 After the review of this items, the device: ☒Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third- party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature: Name: Benson Chiu Date: 2026-08-06 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications.

ShiftCam Limited Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Product Similarity Declaration Product name: ProRig Model name: S-BG01, SB-BG01-XXX (“XXX" is any combination of 0-9 or A-Z, representing features unrelated to the device's performance, such as the material of the plastic panel, appearance color, pattern, etc.) FCC ID: 2A7IM-SBG01 We (ShiftCam Limited) hereby state that all the models are electrical identical including the same circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc., Their differences are model name, color and the appearance of the accessories due to trading purpose. Please kindly handle on the project. Signature: Name: Benson Chiu Title: General Manager 2026/08/06

C5266091_X10_Ed.1 1/1 ShiftCam Limited Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 08/06 /2026 Subject: Request for Confidentiality FCC ID: 2A7IM-SBG01 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential do cuments and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Benson Chiu Title: General Manager

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: ShiftCam Limited Address: Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Product Name: ProRig Model Number: S-BG01, SB-BG01-XXX (“XXX" is any combination of 0-9 or A-Z, representing features unrelated to the device's performance, such as the material of the plastic panel, appearance color, pattern, etc.) FCC Identifier: 2A7IM-SBG01 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Benson Chiu Date: 08/06/2026 Title: General Manager Signature of applicant:

FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 External photos FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 FCC ID: 2A7IM-SBG01 IC: 30569-SBG01

2A7IM-SBG01 30569-SBG01 CMIIT ID: XXXXX

FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 Internal photos FCC ID: 2A7IM-SBG01 IC: 30569-SBG01 RF Chip RF Antenna FCC ID: 2A7IM-SBG01 IC: 30569-SBG01

Report No.: NTC2607345F01 Dongguan Nore Testing Center Co., Ltd. Address: Room 101, 1101, Building 2, No. 61, Hongmei Section, Wangsha Road, Hongmei Town, Dongguan, Guangdong, People's Republic of China Web: www.ntc-c.com Tel:+86-769-2202 2444 Fax:+86-769-2202 2799 Page 1 of 11 RF EVALUATION TEST REPORT Applicant......................... : ShiftCam Limited Address........................... : Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Manufacturer.................... : Dongguan SCT Technology Co., Ltd. Address.......................... : Room 202, Building C, No.33, Jinfu Road, Liaobu Town, Dongguan City, Guangdong Province Factory ......................... : Dongguan SCT TECHNOLOGY CO., LTD Address ......................... : Room 202, Building C, No.33, Jinfu Road, Liaobu Town, Dongguan City, Guangdong Province Product Name.................. : ProRig Brand Name..................... : SHIFTCAM Model No. ........................ : S-BG01, SB-BG01-XXX (For model difference refer to section 2) FCC ID............................ : 2A7IM-SBG01 Measurement Standard...... : 47 CFR PART 2, Section 2.1093 Receipt Date of Samples.... : July 24, 2026 Date of Tested.................. : July 24, 2026 to July 30, 2026 Date of Report.................. : August 07, 2026 This report shows that above equipment is technically compliant with the requirements of the standards above. All test results in this report apply only to the tested sample(s). Without prior written approval of Dongguan Nore Testing Center Co., Ltd, this report shall not be reproduced except in full. Prepared by Al ina Guo / Project Engineer Approved by Iori Fan / Authorized Signatory Report No.: NTC2607345F01 Page 2 of 11 Table of Contents 1. General Description of EUT ................................................................................................................................ 4 2. Test Facility and Location ................................................................................................................................... 6 3. Applicable Standards and References ................................................................................................................ 7 4. Maximum Permissible Exp osure Limit ................................................................................................................ 8 5. RF Exposure Evaluation Results ...................................................................................................................... 11 Report No.: NTC2607345F01 Page 3 of 11 Revision History Report Number Description Issued Date NTC2607345F01 Initial Issue 2026-08-07 Report No.: NTC2607345F01 Page 4 of 11 1. General Description of EUT Product Information Product Name: ProRig Main Model Name: S-BG01 Additional Model Name: SB-BG01-XXX (“XXX" is any combination of 0-9 or A-Z, representing features unrelated to the device's performance, such as the material of the plastic panel, appearance color, pattern, etc.) Model Difference: These models have the same circuit schematic, construction, PCB Layout and critical components. Their differences are model name, color and the appearance of the accessories due to trading purpose. S/N: 2607-4240 Brand Name: SHIFTCAM Hardware Version: 20260710 Software Version: 20260611-01 Rating: DC Port: DC 5V Battery: DC 3.7V li-ion battery Typical Arrangement: Table-top I/O Port: Refer to the user manual Accessories Information Adapter: N/A Cable: N/A Other: N/A Additional Information Note: 1. The product will be shipped with accessories of different colors. The accessories do not have circuits. 2. According to model differences and the requirements of the manufacturer, all tests were performed on model S-BG01. Remark: All the information above are provided by the manufacturer. More detailed feature of the EUT please refers to the user manual. Report No.: NTC2607345F01 Page 5 of 11 Technical Specification (BLE) Bluetooth Version: V5.4 Frequency Range: 2402-2480MHz Modulation Type: GFSK Number of Channel: 40 (refer to following channel list for details) Channel Space: 2MHz Antenna Type: Chip Antenna Number of Antenna 1 Antenna Gain: 2.7 dBi (Declared by the manufacturer) RF PHY Support: 1Mbps, 2Mbps Note: The EUT supports BLE technology only. Report No.: NTC2607345F01 Page 6 of 11 2. Test Facility and Location Test Site : Dongguan Nore Testing Center Co., Ltd. (Dongguan NTC Co., Ltd.) Accreditations and Authorizations : The Laboratory has been assessed and proved to be in compliance with CNAS/CL01 Listed by CNAS, August 13, 2018 The Certificate Registration Number is L5795. The Certificate is valid until August 13, 2030 The Laboratory has been assessed and proved to be in compliance with ISO17025 Listed by A2LA, November 01, 2017 The Certificate Registration Number is 4429.01 The Certificate is valid until December 31, 2027 Listed by FCC, November 06, 2017 Test Firm Regist ration Number: 907417 Listed by Industry Canada, June 08, 2017 The Certificate Registration Number. Is 46405-9743A Test Site Location : Room 101, 1101, Building 2, No. 61, Hongmei Section, Wangsha Road, Hongmei Town, Dongguan, Guangdong, People's Republic of China Report No.: NTC2607345F01 Page 7 of 11 3. Applicable Standards and References According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: Test Standards: 47 CFR Part 1, 1.1307 47 CFR Part 2, 2.1093 KDB 447498 D04 v01 Report No.: NTC2607345F01 Page 8 of 11 4. Maximum Permissible Exposure Limit According to 47 CFR Part 1, 1.1307, for single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: 47 CFR Part 1, 1.1307 (A) The available maximum time- averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria othe…

Text truncated - open the document above for the full version.

Report No.: NTC2607345FV00 Dongguan Nore Testing Center Co., Ltd. Address: Room 101, 1101, Building 2, No. 61, Hongmei Section, Wangsha Road, Hongmei Town, Dongguan, Guangdong, People's Republic of China Web: www.ntc-c.com Tel:+86-769-2202 2444 Fax:+86-769-2202 2799 Page 1 of 61 FCC RADIO TEST REPORT Applicant.......................... : ShiftCam Limited Address............................ : Unit 4A, 4/F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, ShaTin, NT Hong Kong Manufacturer..................... : Dongguan SCT Technology Co., Ltd. Address............................ : Room 202, Building C, No.33, Jinfu Road, Liaobu Town, Dongguan City, Guangdong Province Factory............................ : Dongguan SCT TECHNOLOGY CO., LTD Address........................... : Room 202, Building C, No.33, Jinfu Road, Liaobu Town, Dongguan City, Guangdong Province Product Name................... : ProRig Brand Name...................... : SHIFTCAM Model No. ........................ : S-BG01, SB-BG01-XXX (For model difference refer to section 2) FCC ID............................ : 2A7IM-SBG01 Measurement Standard....... : 47 CFR FCC Part 15, Subpart C (Section 15.247) Receipt Date of Samples..... : July 24, 2026 Date of Tested................... : July 24, 2026 to July 30, 2026 Date of Report................... : August 07, 2026 This report shows that above equipment is technically compliant with the requirements of the standards above. All test results in this report apply only to the tested sample(s). Without prior written approval of Dongguan Nore Testing Center Co., Ltd, this report shall not be reproduced except in full. Prepared by Al ina Guo / Project Engineer Approved by Iori Fan / Authorized Signatory Report No.: NTC2607345FV00 Page 2 of 61 Table of Contents 1. Summary of Test Result ...................................................................................................................................... 4 2. General Description of EUT ................................................................................................................................ 5 3. Test Channels and Modes Detail ........................................................................................................................ 8 4. Configuration of EUT ........................................................................................................................................... 8 5. Modification of EUT ............................................................................................................................................. 8 6. Description of Support Device ............................................................................................................................. 9 7. Test Facility and Location ................................................................................................................................. 10 8. Applicable Standards and References .............................................................................................................. 11 9. Deviations and Abnormalities from Standard Conditions ................................................................................. 11 10. Test Conditions ............................................................................................................................................... 12 11. Measurement Uncertainty ............................................................................................................................... 13 12. Sample Calculations ....................................................................................................................................... 14 13. Test Items and Results ................................................................................................................................... 15 13.1 Conducted Emissions Measurement ............................................................................................................ 15 13.2 Maximum Conducted Output Power Measurement ...................................................................................... 19 13.3 6dB Bandwidth Measurement ....................................................................................................................... 21 13.4 Power Spectral Density Measurement ......................................................................................................... 25 13.5 Band Edge and Conducted Spurious Emissions Measurement ................................................................... 29 13.6 Radiated Spurious Emissions and Restricted Bands Measurement ............................................................ 34 13.7 Antenna Requirement ................................................................................................................................... 60 14. Test Equipment List......................................................................................................................................... 61 Report No.: NTC2607345FV00 Page 3 of 61 Revision History Report Number Description Issued Date NTC2607345FV00 Initial Issue 2026-08-07 Report No.: NTC2607345FV00 Page 4 of 61 1. Summary of Test Result FCC Rules Description of Test Result Remarks §15.207 (a) AC Power Cond ucted Emission PASS --- §15.247(b)(3) Maximum Conducted Output Power PASS --- §15.247(a)(2) 6dB Bandwidth PASS --- §15.247(e) Power Spectral Density PASS --- §15.247(d) Band Edge and Conducted Spurious Emissions PASS --- §15.247(d), §15.209, §15.205 Radiated Spurious Emissions and Restricted Bands PASS --- §15.203 Antenna Requirement PASS --- Report No.: NTC2607345FV00 Page 5 of 61 2. General Description of EUT Product Information Product Name: ProRig Main Model Name: S-BG01 Additional Model Name: SB-BG01-XXX (“XXX" is any combination of 0-9 or A-Z, representing features unrelated to the device's performance, such as the material of the plastic panel, appearance col…

Text truncated - open the document above for the full version.

2.4GHz2012ChipAntenna:RANT0805F245S5 _ Application: WLAN,802.11b/g,Bluetooth,WLAN, etc... Features SMD,highreliability,ultraImpact,Omni-directional... PartnumberInformation RANT0805F245S5 ( A ) ( B ) ( C ) ( D ) ( E ) ( F ) E l e c t r i c a l S p e c i f i c a t i o n D i m e n s i o n a n d T e r m i n a l C o n f i g u r a t i o n N o . T e r m i n a l N a m e 1Feeding/GNG 2G N D / F e e d i n g ( A ) P r o d u c t T y p e C h i p A n t e n n a ( B ) S i z e C o d e 1 . 6 x 0 . 8 m m ( ± 0 . 1 m m ) ( C ) M a t e r i a l H i g h K m a t e r i a l ( D ) F r e q u e n c y 2 . 4 ~ 2 . 5 G H z (E)FeedingmodePIFA& SingleFeeding ( F ) A n t e n n a t y p e T y p e = 5 W o r k i n g F r e q u e n c y R a n g e 2 4 0 0 ~ 2 5 0 0 M H z B a n d w i d t h 1 2 0 M H z ( M i n . ) PeakGain2.7 dBi(Typ.) I m p e d a n c e 5 0 O h m R e t u r n l o s s 1 0 d B ( M i n ) P o l a r i z a t i o n L i n e a r A z i m u t h B e a m w i d t h O m n i - d i r e c t i o n a l O p e r a t i o n T e m p e r a t u r e ( °C ) - 4 0 ~ 8 5 °C R e s i s t a n c e t o S o l d e r i n g H e a t s 1 0 s e c . ( @ 2 8 0 °C ) T e r m i n a t i o n N i / A u ( L e a d l e s s ) D i m e n s i o n ( m m ) L 2 . 0 0 ± 0 . 1 0 W 1 . 2 0 ± 0 . 1 0 T 0 . 4 5 ± 0 . 1 0 咏成國際科技有限公司 電話 : 13530576606 RAIN International Technology Co., Ltd. TEL: 13530576606 廣東省深圳市寶安區西鄉街道銳特科技園 A 棟 7 樓 707 室 Room 707, 7/F, Block A, Ruite Science & Technology Park, Xixiang Subdistrict, Bao'an District, Shenzhen, Guangdong, China China 2.4GHz2012ChipAntenna:RANT0805F245S5 _ 1 EvaluationBoardReference PCBDimensionUnit:mm ReturnLoss&Radiation 0805footprint (ANT) 0805footprint (ANT) 0805footprint (ANT) 0805footprint (ANT) 0805footprint (ANT) 0805footprint (ANT) 0805footprint (ANT) 0805footprint (ANT) 2.4GHz2012ChipAntenna:RANT0805F245S5 _ 2.4GHz2012ChipAntenna:RANT0805F245S5 _ TapingSpecifications ReelandTapingSpecification ReelSpecification TYPESIZEABCD 16087”4K/Reel 4.0±0.5 4.0±213.5±0.5178±2 TappingSpecification PackagingTypeABWEFGHTψDP PaperType1608 1.90±0.203.50±0.208.0±0.201.75±0.103.5±0.054.0±0.102.0±0.050.75±0.10 1.50±0.10 4.0±0.1 2.4GHz2012ChipAntenna:RANT0805F245S5 _ ReliabilityTable TestItemProcedure Requirements CeramicType Remark (Reference) E…

Text truncated - open the document above for the full version.