2A7IM-SG001SnapGrip+SnapLight

Bluetooth and wireless charging cannot be used simultaneously while charging FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Bluetooth and wireless charging cannot be used simultaneously while charging FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant…

Text truncated - open the document above for the full version.

ShiftCam Limited FCC Agent Authorization Letter Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 9/2/2022 SUBJECT: FCC Application for FCC ID: 2A7IM-SG001 To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen Microtest Co., Ltd in 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China on our behalf, to apply to the Federal Communications Commission for our equipment. Any and all acts carried out by Shenzhen Microtest Co., Ltd of our own. on our behalf shall have the same effect as acts This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti -Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Client’s signature: Client’s name & title: Benson Chiu / General Manager Contact information / address: Phone: (852)26200660 Address: Unit 10, 7/ F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, Shatin, NT, Hong Kong

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: ________________ Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Type of Confidentiality Requested Exhibit Type ☐Short Term ☐Permanent Block Diagrams ☐Short Term External Photos ☐Short Term ☐Permanent* Internal Photos ☐Short Term ☐Permanent Operation Description ☐Short Term ☐Permanent Parts List/BOM ☐Short Term ☐Permanent Schematics ☐Short Term Test Setup Photos ☐Short Term ☐Permanent* User manual *Requires further justification before permanent confidentiality will be allowed. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for an initial period of ____________ days. Sincerely, Client’s signature: ________________________________ Client’s name & title: _____________________________ Contact information / address:

ShiftCam Limited. Model difference statement Product Name: SnapGrip+SnapLight Model N o.: SG001-XX, SG001-MN, SG001-AB, SG001-BJ, SG001-PK, SG001-PO We (ShiftCam Limited., Unit 10, 7/ F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, Shatin, NT, Hong Kong) hereby state that all the models are the same circuit and module, except the model name and color. Signature: Name: Benson Chiu Title: General Manager Tel: (852)26200660 Email: [email protected] Date: 9.1.2022

Page1of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Appendix - Ext Photos Model: SG001-XX Photo 1 Photo 2 Page2of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 Page3of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 Page4of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 7 Photo 8 Page5of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 9 Photo 10 Page6of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 11 Photo 12 Page7of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 13 Photo 14 Page8of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 15 Photo 16 Page9of9 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 17 ----End of Report----

Siza：26x50mm

Page 1 of 6 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Appendix - EUT Photos Model: SG001-XX Photo 1 Photo 2 Page 2 of 6 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 Coil ANT Page 3 of 6 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 PCB ANT Page 4 of 6 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 7 Photo 8 Page 5 of 6 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 9 Photo 10 Page 6 of 6 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 11 Photo 12 ----End of Report----

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] RF EXPOSURE Test Report Report No.: MTi220629006-01E3 Date of issue: 2022-09-14 Applicant: ShiftCam Limited Product: SnapGrip+SnapLight Model(s): SG001-XX, SG001-MN, SG001-AB, SG001-BJ, SG001-PK, SG001-PO FCC ID: 2A7IM-SG001 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 6- Report No.: MTi220629006-01E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 6- Report No.: MTi220629006-01E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] TEST RESULT CERTIFICATION Applicant’s name .................... ShiftCam Limited Address .................................. Unit 10, 7/ F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, Shatin, NT, Hong Kong Manufacturer's Name ............. Shenzhen iSonteck Co., Ltd. Address .................................. 5th Floor, Central Control Building, Hengfeng Industrial City, No. 739 Zhoushi Road, Hezhou Community, Hangcheng Street, Bao'an District, Shenzhen Factory's Name ...................... Shenzhen iSonteck Co., Ltd. Address .................................. 5th Floor, Central Control Building, Hengfeng Industrial City, No. 739 Zhoushi Road, Hezhou Community, Hangcheng Street, Bao'an District, Shenzhen Product description Product name ........................... SnapGrip+SnapLight Trademark ............................. shiftcam Model Name .......................... SG001-XX Serial Model ........................... SG001-MN, SG001-AB, SG001-BJ, SG001-PK, SG001-PO Standards ............................... N/A Test procedure ....................... KDB 447498 D01 v06 Date of Test Date (s) of performance of tests ............ : 2022-07-26 ~ 2022-08-27 Test Result ............................................. : Pass This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Testing Engineer : (Letter Lan) Technical Manager : ( Leon Chen) Authorized Signatory : ( Tom Xue) - Page 4 of 6- Report No.: MTi220629006-01E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Table of Contents 1. STANDALONE SAR TEST EXCLUSION CONSIDERATIONS ............................................................................................ 5 2. SAR TEST EXCLUCSION THRESHOLDS ........................................................................................................................ 6 - Page 5 of 6- Report No.: MTi220629006-01E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] 1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance defined in 4.1 f) is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified, typically in the SAR measurement or SAR analysis report, by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting are required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions. a) For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g…

Text truncated - open the document above for the full version.

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 We b : www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi220629006-01E4 Date of issue: 2022-09-14 Applicant: ShiftCam Limited Product: SnapGrip+SnapLight Model(s): SG001-XX, SG001-MN, SG001-AB, SG001-BJ, SG001-PK, SG001-PO FCC ID: 2A7IM-SG001 Shenzhen Microtest Co., Ltd. http://www.mtitest.com Page 2 of 18 Report No.: MTi220629006-01E4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Instructions 1. This test report shall not be partially reproduced without the written consent of the laboratory. 2. The test results in this test report are only responsible for the samples submitted 3. This test report is invalid without the seal and signature of the laboratory. 4. This test report is invalid if transferred, altered, or tampered with in any form without authorization. 5. Any objection to this test report shall be submitted to the laboratory within 15 days from the date of receipt of the report. Page 3 of 18 Report No.: MTi220629006-01E4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Contents 1 General Description ........................................................................................................................ 5 1.1 Description of the EUT ....................................................................................................................................... 5 1.2 Description of test modes ................................................................................................................................... 6 1.3 Description of support units ................................................................................................................................ 7 2 Test facilities and accreditations .................................................................................................... 8 2.1 Test laboratory .................................................................................................................................................... 8 3 List of test equipment ..................................................................................................................... 9 4 Test result ...................................................................................................................................... 10 4.2 Test setup ......................................................................................................................................................... 11 4.3 Test Procedures ................................................................................................................................................ 12 4.4 Equipment Approval Considerations item 5 b) of KDB 680106 D01 v03r01 .................................................... 13 4.5 Test results ....................................................................................................................................................... 14 Photographs of the Test Setup ............................................................................................................ 18 Photographs of the EUT....................................................................................................................... 18 Page 4 of 18 Report No.: MTi220629006-01E4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Test Result Certification Applicant: ShiftCam Limited Address: Unit 10, 7/ F, Goldfield Industrial Centre, 1 Sui Wo Road, Fo Tan, Shatin, NT, Hong Kong Manufacturer: Shenzhen iSonteck Co., Ltd. Address: 5th Floor, Central Control Building, Hengfeng Industrial City, No. 739 Zhoushi Road, Hezhou Community, Hangcheng Street, Bao'an District, Shenzhen Factory: Shenzhen iSonteck Co., Ltd. Address: 5th Floor, Central Control Building, Hengfeng Industrial City, No. 739 Zhoushi Road, Hezhou Community, Hangcheng Street, Bao'an District, Shenzhen Product description Product name: SnapGrip+SnapLight Trademark: shiftcam Model name: SG001-XX Serial Model: SG001-MN, SG001-AB, SG001-BJ, SG001-PK, SG001-PO Standards: FCC CFR 47 PART 1, § 1.1310 Test method: KDB 680106 v03r01 Date of Test Date of test: 2022-07-26 ~ 2022-08-27 Te s t result: Pass Test Engineer : (Letter Lan) Reviewed By: : (Leon Chen) Approved By: : (Tom Xue) Page 5 of 18 Report No.: MTi220629006-01E4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Te l : (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] 1 General Description 1.1 Description of the EUT Product name: SnapGrip+SnapLight Model name: SG001-XX Series Model: SG001-MN, SG001-AB, SG001-BJ, SG001-PK, SG001-PO Model difference: All the models are the same circuit and module, except the model name and color. Electrical rating: SnapGrip: USB-C Input: DC 5V/2A/10W Wireless Charging Output: DC 5V/1A/5W Battery: DC 3.7V/3200mAh/11.84Wh SnapLight: USB-C Input: DC 5V/1A/5W Battery: DC 3.7V/320mAh/1.18Wh Accessories: Cable: USB-A to USB-C cable Hardware version: V8.0 Software version: V1.0 Test sample number: MTi220629006-01-S0001 RF specification: Operation frequency: 115 kHz – 205 kHz Modulation type: ASK Antenna type: Coil Antenna Page 6 of 18 Report No.: MTi220629006-01E4 Address: 101, No. 7, Zone 2, Xinxing …

Text truncated - open the document above for the full version.

东莞市煜耀电子科技有限公司 TEL: 0769-82866410 FAX: 0769-82866409 承 认 书 SPECIFICATION FOR APPROVAL DONGGUAN YUYAO ELECTRONIC TECHNOLOGY CO.,LTD 客户承认 CUSTOMER APPROVE 郑少东姚振东曹前程 客 户: CUSTOMER: 客 户 料 号： CUST P/N: 煜 耀 料 号： YUYAO P/N: 产品型号： D E S T: 日 期： DATE: 版 本： VERSION: 深圳市天孜科技有限公司 Ø20*0.08*105P*10TS-6.4UH-42MM 2022.07.01 V0 制 定 PREPARED BY 审核 CHECKED BY 东莞市煜耀电子科技有限公司 DONGGUAN YUYAO ELECTRONIC TECHNOLOGY CO.,LTD 工厂地址：东莞市塘厦林村新阳路1号新太阳城工业城21栋 TEL: 0769-82866410 FAX: 0769-82866409 批准 APPROVED BY 版本 Rev A.0 东莞市煜耀电子科技有限公司 TEL: 0769-82866410 FAX: 0769-82866409 DONGGUAN YUYAO ELECTRONIC TECHNOLOGY CO.,LTD 2022.07.01新发行 变更前 Before Change 变更后 After Change 变更日期 Change Date 批准 Approved By 版本变更履历 Version Change History 客 户: CUSTOMER: 客 户 料 号： CUST P/N: 煜 耀 料 号： YUYAO P/N: 一、尺寸 DIMENSION:(mm)A 20.5±0.5 B 42.5±0.5 C 43.5±0.5 D 42±2 E 3±1 F 0.8±0.05 G 2.4MAX H I J K L 东莞市煜耀电子科技有限公司 TEL: 0769-82866410 FAX: 0769-82866409 DONGGUAN YUYAO ELECTRONIC TECHNOLOGY CO.,LTD SPECIFICATION APPROVAL V0 审核/日期 CHECKED BY/DATE 姚振东/2022.07.01 制定/日期 PREPARED BY/DATE 郑少东/2022.07.01 天孜科技有限公司 Y-38 产品型号： D E S T: Ø20*0.08*105P*10TS-6.5UH- 42MM 版 本： VERSION: 客 户: CUSTOMER: 客 户 料 号： CUST P/N: 煜 耀 料 号： YUYAO P/N: 二、原理图 SCHEMATIC DIAGRAM: 三、绕线参数 WINDING SPECIFICATION: 序号 NO 1 S F 四、电气特性 ELECTRICAL CHARACTERISTICS: 温度 TEMPERATURE:25°C±10°C,湿度 RELATIVE HUMIDITY:65±20％ 序号 NO 项目 ITEM 1 IND 2 IND 3 DCR 4 Q值 东莞市煜耀电子科技有限公司 TEL: 0769-82866410 FAX: 0769-82866409 DONGGUAN YUYAO ELECTRONIC TECHNOLOGY CO.,LTD 产品型号： D E S T: Ø20*0.08*105P*10TS-6.5UH- 42MM 版 本： VERSION: SPECIFICATION APPROVAL 天孜科技有限公司 V0 圈数 TURNS 绕线方向 WINDING DIRECTION 端子 TERMINAL 线径 WIRE 制定/日期 PREPARED BY/DATE审核/日期 CHECKED BY/DATE 郑少东/2022.07.01姚振东/2022.07.01 S-F S-F 10TS 测试仪器 TEST EQUIPMENTS LCZ METER1062B LCZ METER1062B TH2810 LCZ METER1062B 4.3UH±10％单线圈 6.4UH±10％带磁片 60mΩ MAX 40MIN 100KHZ/1V 0.08*105P丝包线 100KHZ/1V 1KHZ/1V 100KHZ/1V 逆时针 端子 TERMINA L 标准 SPECIFICATION 测试条件 TEST FREQUENCY S-F S-F 客 户: CUSTOMER: 客 户 料 号： CUST P/N: 煜 耀 料 号： YUYAO P/N: 五，产品实物图 PRODUCT PICTURE 六、材料清单 MATERIAL LIST 序号 NO 1 2 3 4 5 6 7 备注：REMARK:以上物料符合ROHS 2.0+REACH环保要求 东莞市煜耀电子科技有限公司 TEL: 0769-82866410 FAX: 0769-82866409 DONGGUAN YUYAO ELECTRONIC TECHNOLOGY CO.,LTD SPECIFICATION APPROVAL 制定/日期 PREPARED BY/DATE审核/日期 CHECKED BY/DATE 郑少东/2022.07.01姚振东/2022.07.01 天孜科技有限公司 材料名称 MATERIAL NAME 线 材 磁 片 RH KHF DB BR 产品型号： D E S T: Ø20*0.08*105P*10TS-6.5UH- 42MM 版 本： VERSION: V0 0.08*105P丝包线 Ø43.5*0.8mm铁氧体磁片 高温环保锡 BE885-9007 8MM高温胶带 双面胶 珍珠棉 锡 条 胶 水 胶 带 背 胶 包 装 制造商 MANUFACTURER 品名描述 DESCRIPTION

Report NO.: SZ13070095E01 Page 2 of 11 1. GENERAL INFORMATION .................................................................................................... 3 2. TECHNICAL INFORMATION ................................................................................................ 4 2.1 Applicant Information .................................................................................................................. 4 2.2 Antenna under Test (AUT) Description ....................................................................................... 4 3. TEST RESULTS ......................................................................................................................... 5 3.1 Applied Reference Documents ..................................................................................................... 5 3.2 Test Conditions ............................................................................................................................. 5 3.3 Test Results lists ........................................................................................................................... 6 3.3.1 Gain and Efficiency ................................................................................................................... 6 ANNEX A. PHOTOGRAPHS ............................................................................................... 7 Report NO.: SZ13070095E01 Page 3 of 11 1. General Information 1.1 Identification of the Responsible Testing Laboratory Company Name: Shenzhen Morlab Communications Technology Co., Ltd. Department: Morlab Laboratory Address: FL.3, Building A, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China 518101 Responsible Test Lab Manager: Mr. Zeng Dexin Telephone: +86 755 36698555 Facsimile: +86 755 36698525 1.2 Identification of the Responsible Testing Location Name: Shenzhen Morlab Communications Technology Co., Ltd. Address: FL.3, Building A, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China 518101 1.3 List of Test Equipments No. Type Specification 1 8960-…

Text truncated - open the document above for the full version.