2A8WM-7INCH-N80Android tablet pc

Android tablet pc 2 3 4 5 6 7 8 2 3 4 5 6 7 FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Shenzhen Anxin Taihe Technology Co., Ltd 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Shenzhen Anxin Taihe Technology Co., Ltd Address: Room 201, No. 7, Baolongjun Industrial Zone, Jiuwo, Longping Community, Dalang Street, Longhua District, Shenzhen Product Name: Android tablet pc FCC ID: 2A8WM-7INCH-N80 Model(s): 7INCH N80 2.911(d)(5)(i) Equipment Type We, [Shenzhen Anxin Taihe Technology Co., Ltd] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Date: 2023.3.29 Title and Company name: Manager/ dunzhang sun NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Anxin Taihe Technology Co., Ltd 2.911 (d)(5)(ii) Applicant Attestation v1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Shenzhen Anxin Taihe Technology Co., Ltd Address: Room 201, No. 7, Baolongjun Industrial Zone, Jiuwo, Longping Community, Dalang Street, Longhua District, Shenzhen Product Name: Android tablet pc FCC ID: 2A8WM-7INCH-N80 Model(s): 7INCH N80 2.911(d)(5)(ii) Applicant filing We, [Shenzhen Anxin Taihe Technology Co., Ltd] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Date: 2023.3.29 Title and Company name: Manager/ dunzhang sun NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Anxin Taihe Technology Co., Ltd U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Baihetian Innovative Solutions FRN: 0033401605 Contact Name: Kenneth Young Street Address: 6837 Chase Rd City/Province/Zip: Dearborn, MI 48126 Telephone No: 313-395-3113 Email: [email protected] This letter is to confirm that we (Baihetian Innovative Solutions) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: Mar 28, 2023 Signed by (Printed Name/Title): Kenneth Young/ Manager The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Shenzhen Anxin Taihe Technology Co., Ltd Grantee Code: 2A8WM Contact Name: dunzhang sun Street Address: Room 201, No. 7, Baolongjun Industrial Zone, Jiuwo, Longping Community, Dalang Street, Longhua District, City/Province/Zip: Shenzhen Telephone No: 0755-21000279 Email: [email protected] Applicant Signature: Date: 2023/03/28 Signed by (Printed Name/Title): dunzhang sun / Manager

Shenzhen Anxin Taihe Technology Co., Ltd Agent Authorization Company: Shenzhen Anxin Taihe Technology Co., Ltd Address: Room 201, No. 7, Baolongjun Industrial Zone, Jiuwo, Longping Community, Dalang Street, Longhua District, Shenzhen Product Name: Android tablet pc Model Number(s): 7INCH N80 Product Description: Android tablet pc We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023/03/29 Name: dunzhang sun Title: Manager Company: Shenzhen Anxin Taihe Technology Co., Ltd

Shenzhen Anxin Taihe Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023/03/29 Subject; Request for Confidentiality FCC ID: 2A8WM-7INCH-N80 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: dunzhang sun Title: Manager

External Photos

Size:40*20mm FCC ID: 2A8WM-7INCH-N80 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Label location

Internal Photos Antenna

FCC ID: 2A8WM-7INCH-N80 RF exposure evaluation §2.1093 Radiofrequency radiation exposure evaluation: Portable Devices. According to§15.247(i) and§1.1307b(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the commission’s guidance. The 1-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  When the minimum test separation distance is < 5 mm, a distance of 5 mm according is applied to determine SAR test exclusion.  The result is rounded to one decimal place for comparison BT  Modulation Frequency (GHz) Max. Power (dBm) Tune up Power (dBm) Max. Tune up Power (dBm) Max. Tune up Power (mW) Test distance (mm) Result exclusion thresholds for 1-g SAR 8DPSK 2.480 3.59 3±1 4 2.51 5 0.79 3.0 2.4G WIFI: Modulation Frequency (GHz) Max. Power (dBm) Tune up Power (dBm) Max. Tune up Power (dBm) Max. Tune up Power (mW) Test distance (mm) Result exclusion thresholds for 1-g SAR 802.11b 2.462 5.66 5±1 6 3.98 5 1.25 3.0 Conclusion: For the max result : 1.25W/Kg ≤ FCC Limit 3.0 for 1g SAR. The Product unsupported at the same time to Transmitting.

No.：BCTC/RF-EMC-007 Page: 1 of 80 Edition：A.5 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2303834775-1E Applicant: Shenzhen Anxin Taihe Technology Co., Ltd Product Name: Android tablet pc Model/Type reference: 7INCH N80 Tested Date: 2023-03-21 to 2023-03-27 Issued Date: 2023-03-27 Report No.: BCTC2303834775-1E No.：BCTC/RF-EMC-007 Page: 2 of 80 Edition：A.5 FCC ID: 2A8WM-7INCH-N80 The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. Product Name: Android tablet pc Trademark: N/A Model/Type Reference: 7INCH N80 Prepared For: Shenzhen Anxin Taihe Technology Co., Ltd Address: Room 201, No. 7, Baolongjun Industrial Zone, Jiuwo, Longping Community, Dalang Street, Longhua District, Shenzhen Manufacturer: Shenzhen Anxin Taihe Technology Co., Ltd Address: Room 201, No. 7, Baolongjun Industrial Zone, Jiuwo, Longping Community, Dalang Street, Longhua District, Shenzhen Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: 2023-03-21 Sample tested Date: 2023-03-21 to 2023-03-27 Issue Date: 2023-03-27 Report No.: BCTC2303834775-1E Test Standards FCC Part15.247 ANSI C63.10-2013 Test Results PASS Remark: This is Bluetooth Classic radio test report. Tested by: Approved by: Brave Zeng/ Project Handler Zero Zhou/Reviewer Report No.: BCTC2303834775-1E No.：BCTC/RF-EMC-007 Page: 3 of 80 Edition：A.5 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 5 2. Test Summary ....................................................................................................... 6 3. Measurement Uncertainty ..................................................................................... 7 4. Product Information And Test Setup ..................................................................... 8 4.1 Product Information ............................................................................................... 8 4.2 Test Setup Configuration ...................................................................................... 8 4.3 Support Equipment ............................................................................................... 9 4.4 Channel List .......................................................................................................... 9 4.5 Test Mode ........................................................................................................... 10 4.6 Table Of Parameters Of Text Software Setting ................................................... 10 5. Test Facility And Test Instrument Used ............................................................... 11 5.1 Test Facility ......................................................................................................... 11 5.2 Test Instrument Used .......................................................................................... 11 6. Conducted Emissions .......................................................................................... 13 6.1 Block Diagram Of Test Setup .............................................................................. 13 6.2 Limit .................................................................................................................... 13 6.3 Test procedure .................................................................................................... 13 6.4 EUT operating Conditions ................................................................................... 13 6.5 Test Result .......................................................................................................... 14 7. Radiated emissions ............................................................................................. 16 7.1 Block Diagram Of Test Setup .............................................................................. 16 7.2 Limit .................................................................................................................... 17 7.3 Test procedure .................................................................................................... 18 7.4 EUT operating Conditions ................................................................................... 19 7.5 Test Result .......................................................................................................... 19 8. Radiated Band Emission Measurement And Restricted Bands Of Operation ..... 23 8.1 Block Diagram Of Test Setup .............................................................................. 23 8.2 Limit .................................................................................................................... 23 8.3 Test procedure .................................................................................................... 24 8.4 EUT operating Conditions ................................................................................... 24 8.5 Test Result .......................................................................................................... 25 9. Spurious RF Conducted Emissions ..................................................................... 26 9.1 Block Diagram Of Test Setup .............................................................................. 26 9.2 Limit .................................................................................................................... 26 9.3 Test procedure .................................................................................................... 26 9.4 Test Result .............…

Text truncated - open the document above for the full version.

Antenna test report 2020 Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen 单击此处添加副标题内容 Customer name Zhongyue Project name N80 Commissioning frequency band WIFI Structure mode FPC Radio frequency engineer Cao Gong Construction engineer Liang Gong Antenna type PIFA Date 2023-03-23 Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen test project equipment 1. （S-1.（Return Loss） Agilent E5071B parameter）2.（VSWR） HP 8753D 2. 1. （TRP）1.ETS 7x4x3 m (3D) Chamber （Active ）2.（TIS） ETS 5x3x3 m (3D) Chamber 2.Agilent 8960 E5515B ×2 StarPoint SP6011 3.1（Gain）1.ETS 7x4x3 m (3D) Chamber （Passive）2 （Efficiency） ETS 5x3x3 m (3D) Chamber 2.Agilent E5071B HP 8753D Test environment Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen Test Equipment Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen Antenna position WIFI Antenna Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen Efficiency and gain Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen Efficiency and gain Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen Address: F3-005, Hongfenghua Internet Creative Park, No. 1, Huangtian Gate Road, Hangcheng Street, Baoan District, Shenzhen Structural drawings Provide better service for our customers address: Building 43, Zhongwu Industrial Zone, Xixiang Street, Bao's District, Shenzhen contacts；linkman：Xiong Qian 17688765727

Report No.: BCTC2303834775-1E No.：BCTC/RF-EMC-007 Page: 78 of 80 Edition：A.5 17.EUT Test Setup Photographs Conducted Measurement Photo Radiated Measurement Photos Report No.: BCTC2303834775-1E No.：BCTC/RF-EMC-007 Page: 79 of 80 Edition：A.5