2A92Z-ECRF200T7RFID Module

Complete Genomics, Inc. Hotline：+1 (888) 811-9644 E-mail： [email protected]； Address：2904 Orchard Parkway San Jose, CA 95134 Website： www.completegenomics.com RFID Module(EC-RF200-T7) The RFID module(model EC-RF200-T7) is prepared by Complete Genomics, Inc. Used to identify chip and kit serial numbers in Genetic Sequencer . It is consists of a RFID Controller and an antenna. Specifications describe: RFID controller Model:EC-RF200 Power supply: 9-30VDC, 1A Antenna Planar RFID antenna Model: EC-UHF-ANT-NF0003 Comply with GB/T 9410-2008; ANSI/IEEE Std149-1979 Size: 113mm × 23mm × 4.5mm Weight: 100g (excluding mounting bracket) Material: Engineering plastic ABS Connector type: SMA type RF coaxial connector Voltage standing wave ratio: ≤ 1.2:1 Gain: -15 dBi Polarization method: linear polarization Antenna impedance: 50 Ω Protection level: IP 65 Working frequency band: 902MHz~928MHz Support protocol: Supports EPC class Gen2 (ISO 18000-6-c), GB/T29768 Working mode: frequency hopping/fixed frequency; Output power: maximum 0.5W, configurable; Working temperature: -25 °C -+70 °C; Storage temperature: -40 °C -+85 °C Working humidity: 10% -95% RH without condensation; Safety regulations: Complete Genomics, Inc. Hotline：+1 (888) 811-9644 E-mail： [email protected]； Address：2904 Orchard Parkway San Jose, CA 95134 Website： www.completegenomics.com 1) Radio License: • EN 302 208; • FCC 47 FCR Part 15C; • SRRC; 2) EMC: EN 301 489; 3) Safety: EN 60 950; 4) ROHS certification: Passed relevant tests according to IEC 62321 standard; Interface definition: 1) POWER interface, external DC9-36V power adapter 2) LAN interface, RJ45 connector definition 8PIN RJ45 Interface Definition Pin Definition Description 1 TX+Transceive Data+ 2 TX - Traceive Data - 3 RX+Receive Data+ 4 NC suspended 5 NC suspended 6 RX - Receive Data - 7 NC suspended 8 NC suspended 3) ANT1, ANT2, ANT3 interfaces, SMA connectors, connecting antennas Complete Genomics, Inc. Hotline：+1 (888) 811-9644 E-mail： [email protected]； Address：2904 Orchard Parkway San Jose, CA 95134 Website： www.completegenomics.com FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IC Note: This device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d’Innovation, Sciences et Développement économique Canada . Son fonctionnement est soumis aux deux conditions suivantes : (1) Ce dispositif ne peut causer d'interférences ; et (2) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux radiations FCC/IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. Complete Genomics, Inc. Hotline：+1 (888) 811-9644 E-mail： [email protected]； Address：2904 Orchard Parkway San Jose, CA 95134 Website： www.completegenomics.com Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C and RSS-247 isue2 has been investigated. It is applicable to the modular transmitter. 2.3 Specific operational use conditions This Modular Approval is limited to OEM installation for mobile and fixed applications only. The antenna installation and operating configurations of this transmitter, including any applicable source-based time averaging duty factor, antenna gain, and cable loss must satisfy MPE categorical Exclusion Requirements of 2.1091. 2.4 Limited module procedures This module will only use in Complete Genomics, Inc.’s host device only. We will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufactu…

Text truncated - open the document above for the full version.

Complete Genomics, Inc. 2904 ORCHARD PARKWAY SAN JOSE, CA 95134, US Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-7-13 To whom it may concern: We, Complete Genomics, Inc., hereby certify that the equipment for which authorization is sought (FCC ID: 2A92Z-ECRF200T7) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Miaoli Yan Manager Complete Genomics, Inc. 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Complete Genomics, Inc. 2904 ORCHARD PARKWAY SAN JOSE, CA 95134, US Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-7-13 U.S. Agent Designation Complete Genomics, Inc. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2A92Z-ECRF200T7): Name and company of U.S. agent: Complete Genomics, Inc. Physical U.S. address of agent: 2904 ORCHARD PARKWAY SAN JOSE, CA 95134, US FRN of U.S. agent: 0033289026 Email address of U.S. agent: [email protected] Complete Genomics, Inc. acknowledges their obligation to accept service of process on behalf of Complete Genomics, Inc.. Complete Genomics, Inc. with the FRN [0033289026] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Miaoli Yan Manager Complete Genomics, Inc. Signature Miaoli Yan Manager Complete Genomics, Inc. 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2023-7-13> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2A92Z-ECRF200T7 EC-RF200-T7 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Miaoli Yan/Manager Company: Complete Genomics, Inc. Address: 2904 ORCHARD PARKWAY SAN JOSE, CA 95134, US Phone: 18998996969 Fax: 0755-27521059 E-Mail: [email protected]

Complete Genomics, Inc. 2904 ORCHARD PARKWAY SAN JOSE, CA 95134, US Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-7-13 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2A92Z-ECRF200T7 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Miaoli Yan/Manager Company: Complete Genomics, Inc. Address: 2904 ORCHARD PARKWAY SAN JOSE, CA 95134, US Phone: 18998996969 Fax: 0755-27521059 E-Mail: [email protected]

Complete Genomics, Inc. 2904 ORCHARD PARKWAY SAN JOSE, CA 95134 Tel: ++86 18998996969 Fax: +86- 0755-27521059 Modular Approval Letter Date: July 13, 2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subjects: Modular Approval Letter The Device,FCC ID: 2A92Z-ECRF200T7, is seeking FCC authorization as a modular transmitter. The EUT meets the requirement for modular approval as detailed in FCC Public Notice DA 00-1407. Compliance to each of the requirement is described below: (a) The radio elements must have the radio frequency circuitry be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. Yes. All produced modulars will have integrated RF shielding. (b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation. Yes. (c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. The modular with power management chip TPS5430DDA. (d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. Allowed antennas given in certification application information and manual (e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing. The modular was tested in a standalone configuration apart from host units RF cexposure evaluation performed at 20cm.. . (f) The module shall comply with the Category I equipment labeling requirements and CFR § 15.212(a)(1)(vi). Complete Genomics, Inc. 2904 ORCHARD PARKWAY SAN JOSE, CA 95134 Tel: ++86 18998996969 Fax: +86- 0755-27521059 The modular has its own FCC ID number. (g) The module shall comply with any applicable FCC RF exposure requirement which are based on the intended use/configurations. Yes，the module is intended to use in protable/mobile environment. FCC RF exposure requirement satisfied with 47CFR §2.1093. (h) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. Yes If you have any questions, please feel free to contact us at the address shown below Sincerely, Name: Miaoli Yan Company: Complete Genomics, Inc. Address: 2904 ORCHARD PARKWAY SAN JOSE, CA 95134 Phone: +86 18998996969 Fax: +86- 0755-27521059 E-Mail: [email protected]

FCC ID: 2A92Z-ECRF200T7 IC: 29863-ECRF200T7

FCC ID: 2A92Z-ECRF200T7 IC: 29863-ECRF200T7

RF Exposure evaluation FCC ID: 2A92Z-ECRF200T7 Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Mobile Device 1. Reference According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. KDB447498 D01: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 2. Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 1842/f 61.4 / / 1.63 4.89/f 0.163 / / (100) * (900/f 2 )* 1.0 f/300 5 6 6 6 6 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 824/f 27.5 / / 1.63 2.19/f 0.073 / / (100) * (180/f 2 )* 0.2 f/1500 1.0 30 30 30 30 30 F=frequency in MHz *=Plane-wave equivalent power density 3. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. Antenna Information The device can use antennas certificated as follows provided by manufacturer; Type Antenna type Frequency Range Antenna Gain EC-UHF-ANT-NF0003 External Planar RFID antenna 840-960MHz -8.02dBi EC-UHF-ANT-NF0001 External Planar RFID antenna 840-960MHz -14.55dBi 5. Conducted power and Manufacturing Tolerance RFID Channel Channel 01 Channel 27 Channel 52 Target (dBm) 15.0 15.0 15.0 Tolerance ±(dB) 1.0 1.0 1.0 6. Standalone MPE Result As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the max. gain of the used antenna, the RF power density can be obtained. Modulation Type Max tune up power tolerance(dBm) Max Output power to antenna (mW) Antenna Gain (Numeric) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result ASK 16 39.8107 0.1578 0.0012 0.6185 Pass 7. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. ----------------THE END OF REPORT---------------

ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page1of10 TestingReport CustomerName:EC-LINKAutomation(Shenzhen)Co.Ltd. ProductName:PlanarRFIDantenna SampleModel:EC-UHF-ANT-NF0001 ReferenceStandard:GB/T9410-2008;ANSI/IEEEStd149-1979 IssueDate:2023.6.5 Engineer:Date: Auditor:Date: Approver:Date: ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page2of10 Version VersionNo.DateDescriptionFormulateApproval A02023.6.5Forthefirsttime,formulateZkrisEason Contents 1.GeneralInformation.........................................................................................................................3 1.1Generalinformationoftestinginstitutions...........................................................................3 1.2Testingprinciple...................................................................................................................3 1.3Testequipment......................................................................................................................4 1.4Testenvironment...................................................................................................................4 1.5Statement..............................................................................................................................4 2.SampleInformation.........................................................................................................................5 2.1Clientinformation.................................................................................................................5 2.2DescriptionofEUT(S)..........................................................................................................5 2.3EUTappearance....................................................................................................................6 2.4EUTsetupphotooffreespaceOTAtesting.........................................................................6 3.TestResults.....................................................................................................................................7 3.1Teststandard.........................................................................................................................7 3.2Testuncertainty.....................................................................................................................7 3.3Testdata................................................................................................................................8 3.3.1VSWRparameters.....................................................................................................8 3.3.2VSWRdata................................................................................................................8 3.3.3Typicalfreespaceefficiencyandgain......................................................................8 3.3.4Typicalfreespaceradiationpattern...........................................................................9 （Thefollowingisblank）..............................................................................................................10 ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page3of10 1.GeneralInformation 1.1Generalinformationoftestinginstitutions Name ShenzhenRFI-LABCommunicationTechnologyCo.,Ltd. Address 10/FA,LingyunBld,LiufangRd,BaoanDistrict,SZ Tel 13682621346 E-mail [email protected] Equipment AlltheequipmentusedinthereportisfixedinZoneB,WestSideof1/F,Building1, TingweiIndustrialPark,No.6LiufangRoad,Bao'anDistrict,Shenzhen 1.2Testingprinciple ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page4of10 1.3Testequipment EquipmentModelNo.SerialNo.Manufacturer Calibration date Next calibration date OTATest System RayZone-5000 RFI-LAB-RF -D00 GTS2023.3.142025.3.13 Network Analyzer E5071C RFI-LAB-RF -D01 KEYSIGHT2023.5.112024.5.10 Network Analyzer E5071C RFI-LAB-RF -C02 KEYSIGHT2023.5.112024.5.10 1.4Testenvironment Temperature 24.2°C Humidity 59%RH Pressure 100.15kPa 1.5Statement (1)Thetestresultsinthereportareonlyapplicabletothetestedsamplesandthetestedsamples workundertheenvironmentdescribedinthereport. (2)OnlyShenzhenRFI-LABCommunicationTechnologyCo.,Ltd.havetherighttomodifythe report,andthemodificationinformationshallbeannotatedintherevisionform. (3)Anyobjectiontothisreportshallberaisedwithin30daysafterformalconfirmationofthe report. (4)Thisreportisinvalidifthereisanyevidencethatthesampleinformationprovidedisfalsified. (5)Thereportisinvalidwithoutthesignatureoftheauditorandapprover. ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page5of10 2.SampleInformation 2.1Clientinformation Name EC-LINKAutomation(Shenzhen)Co.Ltd. Address Room2206,BlockB,ShixiaXintianCentury,BusinessCenter,Futian District,ShenzhenCity,China Contacts / Tel / E-mail / Manufacturer / Manufacturer Address / 2.2DescriptionofEUT(S) ProductName PlanarRFIDantenna SampleModel EC-UHF-ANT-NF0001 AntennaSize / SerialNo. / AntennaType PCBAntenna TestItem VSWR;Antennagain;Efficiency;Radiationpattern FrequencyRange 840-960MHz ReceivedDate 2023.6.1 TestDate 2023.6.1 Remark / ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page6of10 2.3EUTappearance 2.4EUTsetupphotooffreespaceOTAtesting Planform Frontview ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page7of10 3.TestResults 3.1Teststandard NameParameterMethodStandardno. Mobile communication antenna Antennagain Genericspecification forantennasusedinthe mobilecommunications GB/T 9410-2008 Radiationpattern VSWR Antenna Radiationefficiency IEEEStandardTest ProceduresforAntennas ANSI/IEEEStd 149-1979 Gainanddirectivity 3.2Testuncertainty TheuncertaintywascalculatedonthebasisoftheGUMpublishedbyISO,usingthe inclusionfactorofK=2andthe95%confidenceleveltoexpresstheextended uncertainty. ItemUncertainty VSWR±0.3 Antennagain±0.72dB Radiationefficiency±0.72dB ReportNo.:RFI-LAB-RF-202305-EE37 QP030-E41 Page8of10 3.3Testdata 3.3.1VSWRparameters 3.3.2VSWRdata 3.3.3Typicalfreespaceefficiencyandgain Frequency/MHz 840900960 VSWR 2.90023.08924.9018 Frequency/MHz 840850860870880890900910920930940950960 PeakGain/dBi -14.96…

Text truncated - open the document above for the full version.

ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page1of10 TestingReport CustomerName:EC-LINKAutomation(Shenzhen)Co.Ltd. ProductName:PlanarRFIDantenna SampleModel:EC-UHF-ANT-NF0003 ReferenceStandard:GB/T9410-2008;ANSI/IEEEStd149-1979 IssueDate:2023.6.9 Engineer:Date: Auditor:Date: Approver:Date: ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page2of10 Version VersionNo.DateDescriptionFormulateApproval A02023.6.9Forthefirsttime,formulateZkrisEason Contents 1.GeneralInformation.........................................................................................................................3 1.1Generalinformationoftestinginstitutions...........................................................................3 1.2Testingprinciple...................................................................................................................3 1.3Testequipment......................................................................................................................4 1.4Testenvironment...................................................................................................................4 1.5Statement..............................................................................................................................4 2.SampleInformation.........................................................................................................................5 2.1Clientinformation.................................................................................................................5 2.2DescriptionofEUT(S)..........................................................................................................5 2.3EUTappearance....................................................................................................................6 2.4EUTsetupphotooffreespaceOTAtesting.........................................................................6 3.TestResults.....................................................................................................................................7 3.1Teststandard.........................................................................................................................7 3.2Testuncertainty.....................................................................................................................7 3.3Testdata................................................................................................................................8 3.3.1VSWRparameters.....................................................................................................8 3.3.2VSWRdata................................................................................................................8 3.3.3Typicalfreespaceefficiencyandgain......................................................................8 3.3.4Typicalfreespaceradiationpattern...........................................................................9 （Thefollowingisblank）..............................................................................................................10 ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page3of10 1.GeneralInformation 1.1Generalinformationoftestinginstitutions Name ShenzhenRFI-LABCommunicationTechnologyCo.,Ltd. Address 10/FA,LingyunBld,LiufangRd,BaoanDistrict,SZ Tel 13682621346 E-mail [email protected] Equipment AlltheequipmentusedinthereportisfixedinZoneB,WestSideof1/F,Building1, TingweiIndustrialPark,No.6LiufangRoad,Bao'anDistrict,Shenzhen 1.2Testingprinciple ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page4of10 1.3Testequipment EquipmentModelNo.SerialNo.Manufacturer Calibration date Next calibration date OTATest System RayZone-5000 RFI-LAB-RF -D00 GTS2023.3.142025.3.13 Network Analyzer E5071C RFI-LAB-RF -D01 KEYSIGHT2023.5.112024.5.10 Network Analyzer E5071C RFI-LAB-RF -C02 KEYSIGHT2023.5.112024.5.10 1.4Testenvironment Temperature 24.2°C Humidity 59%RH Pressure 100.15kPa 1.5Statement (1)Thetestresultsinthereportareonlyapplicabletothetestedsamplesandthetestedsamples workundertheenvironmentdescribedinthereport. (2)OnlyShenzhenRFI-LABCommunicationTechnologyCo.,Ltd.havetherighttomodifythe report,andthemodificationinformationshallbeannotatedintherevisionform. (3)Anyobjectiontothisreportshallberaisedwithin30daysafterformalconfirmationofthe report. (4)Thisreportisinvalidifthereisanyevidencethatthesampleinformationprovidedisfalsified. (5)Thereportisinvalidwithoutthesignatureoftheauditorandapprover. ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page5of10 2.SampleInformation 2.1Clientinformation Name EC-LINKAutomation(Shenzhen)Co.Ltd. Address Room2206,BlockB,ShixiaXintianCentury,BusinessCenter,Futian District,ShenzhenCity,China Contacts / Tel / E-mail / Manufacturer / Manufacturer Address / 2.2DescriptionofEUT(S) ProductName PlanarRFIDantenna SampleModel EC-UHF-ANT-NF0003 AntennaSize / SerialNo. / AntennaType PCBAntenna TestItem VSWR;Antennagain;Efficiency;Radiationpattern FrequencyRange 840-960MHz ReceivedDate 2023.6.8 TestDate 2023.6.8 Remark / ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page6of10 2.3EUTappearance 2.4EUTsetupphotooffreespaceOTAtesting Planform Frontview ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page7of10 3.TestResults 3.1Teststandard NameParameterMethodStandardno. Mobile communication antenna Antennagain Genericspecification forantennasusedinthe mobilecommunications GB/T 9410-2008 Radiationpattern VSWR Antenna Radiationefficiency IEEEStandardTest ProceduresforAntennas ANSI/IEEEStd 149-1979 Gainanddirectivity 3.2Testuncertainty TheuncertaintywascalculatedonthebasisoftheGUMpublishedbyISO,usingthe inclusionfactorofK=2andthe95%confidenceleveltoexpresstheextended uncertainty. ItemUncertainty VSWR±0.3 Antennagain±0.72dB Radiationefficiency±0.72dB ReportNo.:RFI-LAB-RF-202306-FF06 QP030-E41 Page8of10 3.3Testdata 3.3.1VSWRparameters 3.3.2VSWRdata 3.3.3Typicalfreespaceefficiencyandgain Frequency/MHz 840900960 VSWR 10.1926.961229.488 Frequency/MHz 840850860870880890900910920930940950960 PeakGain/dBi -20.86…

Text truncated - open the document above for the full version.

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 E-mail: [email protected] TEST REPORT FCC PART 15 SUBPART C 15.247 & RSS-247 Report Reference No. ................ : CTL2304242041-WF Compiled by: ( position+printed name+signature) Happy Guo (File administrators) Tested by: ( position+printed name+signature) Gary Gao (Test Engineer) Approved by: ( position+printed name+signature) Ivan Xie (Manager) Product Name ............................ : RFID Module Model(HVIN) ............................... : EC-RF200-T7 List Model(HVIN) ........................ : N/A Trade Mark ............................…

Text truncated - open the document above for the full version.