2A94QET-BH035True Wireless Earbuds

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help DualM NC BH035 Lx2PCSSx2PCS White Indicator True Wireless Stereo Earbuds User Manual MODEL:ET-BH035 Model Bluetooth Version Earbuds Battery Capacity Charging Case Battery Capacity Rated Voltage Earbuds Fully Charged Time Charging Case Fully Charged Time Music Playback Battery Life Connected Standby Time Charging Port Input ET-BH035 V5.3 37mAh 400mAh 3.7V 1.5H 1.5H 6H (50% Volume) 70H Type-C 5V/1A (Charging Case) Specifications Accessories Touch Button LED LED Charging Case Note: Remove the insulation cover from the earbuds before first use. Put the earbuds into the charging case, and take out for use. All images in this user manual is for illustrative purpose only. Please refer to the actual product. User Manual Type-C Cable Eartips Touch Button FAQ The indicator is off when the charging case is being charged. Make sure the charging port of the charging case is connected to power supply normally. Cannot hear anything from the earbuds Make sure the earbuds are on. Make sure the volume is set properly. Make sure the earbuds are connected to the phone. Make sure the earbuds are within the working range. Phone call effect is not good Make sure the phone is in a strong signal area. The effective working range of the earbuds is 10 meters, please make sure the earbuds are within the working range, and there are no obstacles between the phone and the earbuds. Cannot control with pause, resume and previous/next track while playing music The device paired with the earbuds needs supporting AVRCP (Audio/Video Remote Control Profile) Protocol. Charging Earbuds When the earbuds prompt low battery, put the earbuds into the charging case, the earbuds will be in charging status automatically and the charging case lights up for 4 seconds before going off. The earbuds indicators stay solid blue while charging; the blue light goes off after the earbuds are fully charged. Using Your Earbuds 1. Charging Charging the Case Connect the charging case to any 5V/1A power supply port with the included charging cable. While charging, the charging case is breathing white slowly. After fully charged, the charging case stays solid white. Take out the earbuds from the charging case to turn on. Put back the earbuds to the charging case and close the lid to turn off. Both earbuds were paired with each other when they were produced at the factory. Gaming/Bass/Standard Mode: Tap & Hold L for 2s ANC/Pass Through/Standard Mode: Tap & Hold R for 2s (Mode switch is not available for single earbud) The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG,Inc. and any use of such marks by Sunvalleytek International Inc. is under license. Other trademarks and trade names are those of their respective owners. 2. On/Off For the first connection, open the lid of the charging case, take out both earbuds, and they will enter Bluetooth pairing mode automatically. Earbuds pairing mode: primary earbud flashes blue and white, and secondary earbud has no lighting. Search for “DualM NC BH035”, select to connect, and the primary earbud lighting goes off after the connection is successful. When the earbuds are turned on again, they will connect to the last paired device. If re-connection fails or the Bluetooth is disconnected, they will enter Bluetooth pairing mode automatically. 3. Bluetooth Connection 4. Dual Earbuds TWS Connection Make sure the earbuds were not connected to any device. Tap the touch button of any earbud for FOUR times in any of the following status: a.Single earbud pairing (alternatively flashes blue and white) b.Dual earbuds pairing (left earbud flashes blue and white, right earbud has no lighting) Both earbuds light up blue for 1 second then go off. Turn off the earbuds by placing them into the case. Take out the earbuds to re-pair with your device. 5. Clearing Pairing History 6. Control & Functions Music: Calling: Pause/PlayDouble tap L/R Previous Track Triple tap L Next Track Triple tap R Volume -Tap L once Volume +Tap R once AnswerDouble tap L/R Hang UpDouble tap L/R Reject Tap & Hold L/R for 2s DualM NC BH035 Lx2PCSSx2PCS Weiße Anzeige Modell Bluetooth-Version Ohrhörer-Akkukapazität Akkukapazität der Ladehülle Nennspannung Dauer bis zur vollständigen Aufladung der Ohrhörer Dauer bis zur vollständigen Aufladung der Ladehülle Akkulaufzeit bei Musikwiedergabe Bereitschaftszeit bei bestehender Verbindung Ladeanschluss Eingang ET-BH035 V5.3 37mAh 400mAh 3.7V 1.5h 1.5h 6h (50 % Lautstärke) 70h Type-C 5 V/1 A (Ladehülle) Technische Daten Zubehör Touch-Taste LE LE Ladehülle Hinweis: Entfernen Sie vor der erstmaligen Verwendung die Isolierabdeckung von den Ohrhörern. Platzieren Sie die Ohrhörer in der Ladehülle und nehmen Sie sie zur Benutzung heraus. Alle Bilder in dieser Bedienungsanleitung dienen nur der Veranschaulichung. Orientieren Sie sich am tatsächlichen Produkt. Bedienungsanleitung Type-C-KabelOhrstöp Touch-Taste Häufig gestellte Frag…

Text truncated - open the document above for the full version.

ShenzhenAspironTechnologyCompanyLimited Room2803B,BuildingC, GalaxyWorldPhaseII, MinleCommunity,MinzhiStreet,LonghuaDistrict, Shenzhen,Guangdong,China FederalCommunicationsCommission Authorizationand EvaluationDivision 7435OaklandMillsRoad Columbia,MD 21046 USA Date:03 -01 -2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A94QET-BH035 Product Name: True Wireless Earbuds Model Name: ET-BH035, TT-BH1118 [ShenzhenAspironTechnologyCompanyLimited] (“the applicant”) certifiesthat the equipmentfor whichauthorizationis soughtis not“covered” equipmentprohibitedfromreceivingan equipment authorizationpursuantto section2.903of the FCC rules. Sincerely, (Applicantsignature) (BobbyZou)

2.911 (d)(7)USA Agent v1.2 Section 2.911(d)(7) USAAgent for Service of Process Company name: Shenzhen Aspiron Technology Company Limited Address: Room 2803B, Building C, Galaxy World Phase II, Minle Community, Minzhi Street, Longhua District, Shenzhen, Guangdong, China Product Name: True Wireless Earbuds FCC ID: 2A94QET-BH035 Model(s): ET-BH035, TT-BH1118 2.911(d)(7) USA Designated Agent for Service of Process We, [Shenzhen Aspiron Technology Company Limited] (“the applicant”) designate [VAVA INTERNATIONAL INC.] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent:We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation:We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: VAVA INTERNATIONAL INC. Address: 20370 Town Center Lane Suite 208 Cupertino, CA 95014, United States FRN: 0033406802 Contact Name: Ning Liang Telephone No: 510-767-8112 Email:[email protected] Applicant Company name: Shenzhen Aspiron Technology Company Limited Address: Room 2803B, Building C, Galaxy World PhaseII, Minle Community, Minzhi Street, Longhua District, Shenzhen, Guangdong, China Contact Name: Bobby Zou Telephone No: +86-18571729087 Email:[email protected] Signature: Title:General Manager Signature: Title: Approbation Manager Date:2023.3.13Date: 2023.3.13 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. 2.911(d)(7)USAAgentv1.2 Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-th e-communications-supply-chain-through-the

ShenzhenAspironTechnologyCompanyLimited Room2803B,BuildingC, GalaxyWorldPhaseII, MinleCommunity,MinzhiStreet,LonghuaDistrict, Shenzhen,Guangdong,China FederalCommunicationsCommission Authorizationand EvaluationDivision 7435OaklandMillsRoad Columbia,MD 21046 USA Date:03 -01 -2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A94QET-BH035 Product Name: True Wireless Earbuds Model Name: ET-BH035, TT-BH1118 [ShenzhenAspironTechnologyCompanyLimited] (“the applicant”) certifiesthat,as of the dateof the filingof the application,the applicantis not identifiedon the CoveredList as an entityproducing “covered” equipment. Sincerely, (Applicantsignature) (BobbyZou)

Shenzhen Aspiron Technology Company Limited Room 2803B, Building C, Galaxy World Phase II , Minle Community, Minzhi Street, Longhua District, Shenzhen, Guangdong, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Mar. 01, 2023 Subject; Request for Confidentiality FCC ID: 2A94QET-BH035 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Antenna Specification FCC_Confidential In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Bobby Zou Title:Approbation Manager

承 認 書 SPECIFICATION FOR APPROVAL 客戶名稱 CUSTOMER ： 客戶料號 CUSTOMER’S P/N ： 料號 PART NUMBER ： KBAN3216G245H01 規格 DESCRIPTION ： Chip Antenna 3216 L Ant 2.45G Type H01 版本 VERSION ： V1.0 日期 ISSUE DATE ： 2020/08/21 客 戶 承 認 CUSTOMER APPROVED 工 程 部 R&D CENTER 承 認 APPROVAL 確 認 CHECKED 製 作 DRAWN Ziv Alex Jerry 萬誠科技股份有限公司 OneWave Electronic Co., Ltd. 112台北市北投區立功街151號1樓 1F, No. 151, Li Gong Street, Beitou District, Taipei City 112, Taiwan 電話: (02) 2898-2220 TEL: +886 2 2898-2220 傳真: (02) 2898-5055 FAX: +886 2 2898-5055 2/11 ONEWAVE TECHNOLOGY CO., LTD. 3216 Chip antenna For Bluetooth / WLAN Applications Dimension (mm) L 3.23 ± 0.20 W 1.66 ± 0.20 T 0.45 ± 0.20 P/N: KBAN3216G245H01 3/11 ONEWAVE TECHNOLOGY CO., LTD. Part Number Information KBAN 3216 G 245 H 01 A B C D E F A Product Series Antenna B Dimension L x W 3.2 x 1.6mm (±0.2mm) C Material High K material D Working Frequency 2.4 ~ 2.5GHz E Feeding mode PIFA & Single Feeding F Antenna type Type = 01 1. Electrical Specification Remark : Bandwidth & Peak Gain was measured under evaluation board of next page Specification Part Number KBAN3216G245H01 Central Frequency 2450 MHz Bandwidth 120 (Min.) MHz Return Loss -6.5 (Max) dB Peak Gain 1.73 dBi Impedance 50 Ohm Operating Temperature -40～+110 °C Maximum Power 4 W Resistance to Soldering Heats 10 ( @ 260°C) sec. Polarization Linear Azimuth Beamwidth Omni-directional Termination Ni / Au (Leadless) 4/11 ONEWAVE TECHNOLOGY CO., LTD. 2. Recommended PCB Pattern Evaluation Board Dimension 2 nd Evaluation Board Dimension Suggested Matching Circuit 重要資訊 : 匹配元件建議使用精準度高的電感±0.1~0.3nH、電容±0.1pF 5/11 ONEWAVE TECHNOLOGY CO., LTD. Layout Dimensions in Clearance area( Size=5.9*5.0mm) FootPrint (Unit : mm) ◆ 2 nd Layout Dimensions in Clearance area( Size=8.0*3.0mm) Matching Circuit 50 ohm transmission Line 6/11 ONEWAVE TECHNOLOGY CO., LTD. 3. Measurement Results Return Loss 7/11 ONEWAVE TECHNOLOGY CO., LTD. Radiation Pattern Efficiency Peak Gain Directivity 2400MHz 78.66 % 1.64 dBi 2.68 dBi 2450MHz 81.58 % 1.73 dBi 2.61 dBi 2500MHz 79.88 % 1.68 dBi 2.65 dBi Chamber Coordinate System Z Y X 8/11 ONEWAVE TECHNOLOGY CO., LTD. 4.Reliability and Test Condictions ITEM REQUIREMENTS TEST CONDITION Solderability 1. Wetting shall exceed 90% coverage 2. No visible mechanical damage Pre-heating temperature:150°C/60sec. Solder temperature:230±5°C Duration:4±1sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Solder heat Resistance 1. No visible mechanical damage 2. Central Freq. change :within ± 6% 10 ± 0.5 sec. 60 sec . . T E M P ( °C ) 150 °C 2 6 0 °C Pre-heating temperature:150°C/60sec. Solder temperature:260±5°C Duration:10±0.5sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Component Adhesion (Push test) 1. No visible mechanical damage The device should be reflow soldered(230±5°C for 10sec.) to a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with-ST-F 0.5 Kg without failure of the termination attached to component. Component Adhesion (Pull test) 1. No visible mechanical damage Insert 10cm wire into the remaining open eye bend ,the ends of even wire lengths upward and wind together. Terminal shall not be remarkably damaged. Thermal shock 1. No visible mechanical damage 2. Central Freq. change :within ±6% Phase Temperature(°C) Time(min) 1 +110±5°C 30±3 2 Room Temperature Within 3sec 3 -40±2°C 30±3 4 Room Temperature Within 3sec +110°C=>30±3min -40°C=>30±3min Test cycle:10 cycles The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to High Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: +110±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to Low Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature:-40±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Humidity 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: 40±2°C Humidity: 90% to 95% RH Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. 4±1 sec. 60sec TEMP (°C) 150°C 230°C 9/11 ONEWAVE TECHNOLOGY CO., LTD. 5.Soldering and Mounting Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. ‧Preheat circuit and products to 150°C ‧Never contact the ceramic with the iron tip ‧Use a 20 watt soldering iron with tip diameter of 1.0mm ‧280°C tip temperature (max) ‧1.0mm tip diameter (max) ‧Limit soldering time to 3 sec. SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) 60~120 s 10s max. 30~60s 250~260 230 180 150 TIME(sec.) Reflow Soldering SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) within 3s Gradual cooling 150 TIME(sec.) Iron Soldering Over 60s 350 300 10/11 ONEWAVE TECHNOLOGY CO., LTD. 6.Packaging Information Tape Specification: Reel Specification: (7’’, Φ180 mm) Tape Width(mm) A(mm) B(mm) C(mm) D(mm) Chip/Reel(pcs) 8 9.0±0.5 60±2 13.5±0.5 178±2 3000 11/11 ONEWAVE TECHNOLOGY CO., LTD. 7.Storage and Transportation Information Storage Conditions To maintain the solderability of terminal electrodes: 1. Temperature and humidity conditions: -10~ 40°C and 30~70% RH. 2. Recommended products shoul…

Text truncated - open the document above for the full version.

Report No.: AGC13454230220AP03 Page 1 of 4 EXTERNAL PHOTOS ALL VIEW OF EUT TOP VIEW OF EUT Report No.: AGC13454230220AP03 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC13454230220AP03 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC13454230220AP03 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location The product does not have enough space to place the label, and FCC ID label is located in the user manual and package. User manual as below:

Report No.: AGC13454230220AP03 Page 1 of 5 INTERNAL PHOTOS OPEN VIEW OF EUT (Left) BATTERY VIEW OF EUT Report No.: AGC13454230220AP03 Page 2 of 5 ANTENNA CLOSE-UP PHOTO-1 INTERNAL VIEW OF EUT (FIGURE 1) BT Antenna Report No.: AGC13454230220AP03 Page 3 of 5 INTERNAL VIEW OF EUT (FIGURE 2) OPEN VIEW OF EUT (Right) Report No.: AGC13454230220AP03 Page 4 of 5 BATTERY VIEW OF EUT ANTENNA CLOSE-UP PHOTO-1 BT Antenna Report No.: AGC13454230220AP03 Page 5 of 5 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) ****************************************End of Report*************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description True Wireless Earbuds Model Name ET-BH035 Series Model TT-BH1118 FCC ID 2A94QET-BH035 2. EVALUATION METHOD According to 447498 D01 General RF Exposure Guidance v06 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 3. CALCULATION P t = -2.601dBm=0.549mW The value of the Maximum output power P t is referred to the test report of the CFR47 §15.247. The result for RF exposure evaluation SAR=(0.549mW /5mm) .[√2.441GHz)]=0.17<3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. 4. CONCLUSION The SAR evaluation is not required.

Page 1 of 66 FCC Test Report Report No.: AGC13454230220FE03 FCC ID : 2A94QET-BH035 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : True Wireless Earbuds BRAND NAME : evatronic, TAOTRONICS MODEL NAME : ET-BH035, TT-BH1118 APPLICANT : Shenzhen Aspiron Technology Company Limited DATE OF ISSUE : Feb. 24, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC13454230220FE03 Page 2 of 66 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Feb. 24, 2023 Valid Initial Release Report No.: AGC13454230220FE03 Page 3 of 66 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RECEIVER INPUT BANDWIDTH .............................................................................................................. 7 2.4. EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ......................................................................... 7 2.5. EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ......................................................... 7 2.6. RELATED SUBMITTAL(S) / GRANT (S) .................................................................................................... 8 2.7. TEST METHODOLOGY ............................................................................................................................. 8 2.8. SPECIAL ACCESSORIES ......................................................................................................................... 8 2.9. EQUIPMENT MODIFICATIONS ................................................................................................................. 8 2.10. ANTENNA REQUIREMENT..................................................................................................................... 8 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 9 4. DESCRIPTION OF TEST MODES ................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ................................................................................................................. 11 5.1. CONFIGURATION OF EUT SYSTEM ....................................................................................................... 11 5.2. EQUIPMENT USED IN TESTED SYSTEM ............................................................................................... 11 5.3. SUMMARY OF TEST RESULTS ............................................................................................................... 11 6. TEST FACILITY .............................................................................................................................................. 12 7. PEAK OUTPUT POWER ................................................................................................................................ 13 7.1. MEASUREMENT PROCEDURE ............................................................................................................. 13 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 13 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 14 8. 20DB BANDWIDTH ........................................................................................................................................ 18 8.1. MEASUREMENT PROCEDURE ............................................................................................................. 18 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 18 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 19 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 23 9.1. MEASUREMENT PROCEDURE ............................................................................................................. 23 Report No.: AGC13454230220FE03 Page 4 of 66 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 23 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 23 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 23 10. RADIATED EMISSION ................................................................................................................................. 37 10.1. MEASUREMENT PROCEDURE ........................................................................................................... 37 10.2. TEST SETUP ......................................................................................................................................... 39 10.3. LIMITS AND MEASUREMENT RESULT ............................................................................................... 40 10.4. TEST RESULT........................................................................................................................................ 40 11. NUMBER OF HOPPING FREQUENCY ........................…

Text truncated - open the document above for the full version.

Fanson 2022/12/02 Antenna Test Report G129 V1.0 Customer Dacom Agent LeDiamond Project name G129 Model. IC Jieli Model. ANT KBAN3216G245H01 1 $QWHQQD,QIRUPDWLRQ • $QWHQQD7\SH濣&KLS$QWHQQD 2 $QW0DWFKLQJ /& 31 $QW .%$1*+  1&   5   S)   Q+ • 0DWFKLQJ&LUFXLW • $QWHQQD3ODFHPHQW 3 Ant. 2 Ant. 3 1 5) $QW 4 Fre.(MHz) 2400 2450 2483 S11(dB) -11.5 -17.0 -18.3 $QW63DUDPHWHU濑$17濒 4 5 (TXLSPHQWRI27$WHVW 1HWZRUNDQDO\]HU(& %OXHWRRWK&RPSUHKHQVLYH7HVWHU &0: $QHFKRLF&KDPEHU )70'PXOWLSUREH  $QW*DLQ3DWWHUQ#*+] ; < = • $FWLYH7HVW  $QW*DLQ3DWWHUQ#*+] ˄ 'DWH ˅ CH. TIS(dBm) TRP (dBm) BT 0 -88.43 2.57 39 -87.74 3.01 78 -88.46 2.96 ; < = CH. TIS(dBm) TRP (dBm) BT 0 -90.44 2.69 39 -90.59 3.59 78 -90.9 4.1 L R • $FWLYH7HVW  $QW*DLQ3DWWHUQ#*+] ˄ 'DWH ˅ CH. TIS(dBm) TRP (dBm) BT 0 -89.99 2.64 39 -88.83 3.4 78 -88.32 4.2 ; < = CH. TIS(dBm) TRP (dBm) BT 0 -89.45 2.04 39 -88.91 3.08 78 -87.03 3.74 L R • $FWLYH7HVW  $QW*DLQ3DWWHUQ#*+] CH. TIS(dBm) TRP (dBm) BT 0 -83.94 -2.83 39 -83.49 -1.79 78 -81.37 -2.65 ; < = CH. TIS(dBm) TRP (dBm) BT 0 -82.2 -5.21 39 -81.45 -5.7 78 -81.38 -5.9 LR • :LWK+HDG 10 5HDOWHVW • 7HVWHQYLURQPHQW濣(PSW\SDUNLQJORW • 3KRQHPRGHO濣5HGPL. • 7HVWGLVWDQFH濣 PHWHUV • (DUFRYHULQJWHVW濣2.

Report No.: AGC13454230220AP02 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC13454230220AP02 Page 2 of 2 RF CONDUCTED TES SETUP ****************************************End of Report*************************************