2AA72-PTR5610Bluetooth Module

COPYRIGHT ©2019ALLRIGHTS RESERVEDXun Tong Tech TEL: + 86 75526675941 E-mail: [email protected] PTR 5610-S Bluetooth Low Energy Module Specification V1.1 ShenzhenLankeXuntongTechnologyCo.,Ltd WWW.abluetech.com VERSIONDATERELEASE NOTE V1.02019-4-15First release V1.12019-7-16update V1.22019-12-20Modify pin assignment COPYRIGHT ©2019ALLRIGHTS RESERVEDXun Tong Tech TEL: + 86 75526675941 E-mail: [email protected] Index 1. Overview......................................................................................................................................... 1.1. Product introduction............................................................................................................ 1.2. Feature................................................................................................................................. √ Support Bluetooth 5.0 protocol, high-speed transmission.................................................. √ Support information encryption to improve transmission security;................................... √ Support low power advertising mode................................................................................. √ Support to modify the 128-bit UUID.................................................................................. √ Support local and on-air configuration to adapt to different needs.................................... √ Support to configure 4 GPIO as input and output.............................................................. √ Support access key to improve the reliability of connection.............................................. 1.3. Notice................................................................................................................................... 1.4. Typical application frame.................................................................................................... 2. Hardware specification................................................................................................................... 2.1. Package................................................................................................................................ Figure 2 Package diagram........................................................................................................ 2.2. Pin assignment..................................................................................................................... Figure 2 Pin Distribution............................................................................................................ 2.3. Pin definition....................................................................................................................... 2.4. Layout considerations.......................................................................................................... 3. AT Command.................................................................................................................................. 3.1. Basic function...................................................................................................................... 3.1.1. Baud rate................................................................................................................... 3.1.2. Transmit power......................................................................................................... 3.1.3. MAC address............................................................................................................ 3.1.4. Transmission speed on Bluetooth............................................................................. 3.1.5. Work mode................................................................................................................ 3.1.6. Sleep......................................................................................................................... 3.1.7. Factory default setting.............................................................................................. 3.1.8. Software reset........................................................................................................... 3.1.9. Firmware version...................................................................................................... 3.2. Slave command.................................................................................................................... 3.2.1. Advertise name......................................................................................................... 3.2.2. Advertise interval...................................................................................................... 3.2.3. Advertisement type................................................................................................... 3.2.4. Slave data service UUID........................................................................................... 3.2.5. Slave TX characteristic UUID.................................................................................. 3.2.6. Slave RX characteristic UUID.................................................................................. 3.2.7. Slave service configuration UUID............................................................................ 3.2.8. Slave TX configuration Characteristic UUID.......................................................... 3.2.9. Slave RX configuration Characteristic UUID.......................................................... COPYRIGHT ©2019ALLRIGHTS RESERVEDXun Tong Tech TEL: + 86 75526675941 E-mail: [email protected] 3.3. Common Command............................................................................................................. 3.3.1. Switch mode enable.................................................................................................. 3.3.2. Switch Transmission Mode to Command Line Mode.............................................. 3.3.3. Switch Command Line Mode to Transmission Mode...........................…

Text truncated - open the document above for the full version.

Mar 09 ， 2020 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID:_2AA72-PTR5610___________ Product Name:_PTR5610 _________ Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) Schematics Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> NameEcho Wang Title SalesAssitant CompanyLANKE XUNTONG TECHNOLOGY CO.,LTD

Mar 09,2020 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 AuthoritytoActas Agent On our behalf, I appoint QianhaiBlueAsiaofTechnicalSerivices(shenzhen)Limited,No448, BulongRoad,BantianStreet,LonggangDistric (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. Forinstanceswhereourauthorizedagentsignstheapplicationforcertificationonourbehalf,I acknowledgethat allresponsibilityforcomplying withthetermsandconditionsforcertification, stillresideswith LANKE XUNTONG TECHNOLOGY CO.,LTD Room 7A-B, Block B of Wanlian Building,Net Valley, No.12 of Yanshan Road,Nanshan,Shenzhen, China (ApplicantName and address) <Signature> NameEcho Wang Title Sales Assitant CompanyLANKE XUNTONG TECHNOLOGY CO.,LTD

Compliance list INTEGRATION INSTRUCTIONS for 996369 D03 OEM the and 996369 D03 OEM by Sections 2.2 through 2.10. Requirement Yes N/A Comment 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.3 YES Refer to instruction FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain, specifically for master devices in 5 GHz DFS bands. YES Refer to instruction Integral antenna with antenna gain 0dBi 2.4 Limited module procedures If a modular transmitter is approved as a “limited module,” then the module manufacturer is responsible for approving the host environment that the limited module is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions. A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum N/A Not applicable signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured. For additional hosts other than the specific host originally granted with a limited module, a Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. 2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. 4 a) Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna); b) Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency, the wavelength, and antenna shape (traces in phase) can affect antenna gain and must be considered); c) The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC) board layout; d) Appropriate parts by manufacturer and specifications; e) Test procedures for design verification; and N/A Not applicable f) Production test procedures for ensuring compliance. The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. 2.6 RF exposure considerations It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1) to the host product manufacturer, to define the application conditions (mobile, portable – xx cm from a person’s body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility of the module through a change in FCC ID (new application). YES Refer to instruction This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a spec…

Text truncated - open the document above for the full version.

Single Modular approval declaration letter We, LANKE XUNTONG TECHNOLOGY CO.,LTD apply Single modular approval for Product Name: Bluetooth Module Model: PTR5610 FCC ID: 2AA72-PTR5610 According to 996369 D01 Module Equip Auth Guide v01r04 and 15.212 requirement: 1) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must beon the module assembly; Answer ：Yes ， both side shielded 2)The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; Answer ：Ye s ；All inputs to the modules are buffered through logic or microprocessor inputs. 3)The modular transmitter must have its own power supply regulation. Answer ：Ye s ；A low drop out regulator is used for modular power supply regulation. 4)The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); Answer ：Ye s ；Device is equipped with PCB antenna. (5)The module must demonstrate compliance in a stand-alone configuration; Answer ：Yes，distance between modular and all AEs are longer than 10cm ，refer to setup photo. (6) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); Answer ：Yes ；The modular has a permanent fixed label, and below statement was listed in the User Manual;The host device must be labeled to display the FCCID of the moduleContains FCC ID: 2AA72-PTR5610 (7)The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; Answer ：Yes ；The module comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee, Refer to test report and user manual . (8)The module must comply with RF exposure requirements Answer ：Yes ；Transmitter meets MPE calculation of 47 CFR 1.1307 . Refer to MPE Reports and Refer to modular installation manual <Signature> Name Echo Wang Title Sales Assitant Company LANKE XUNTONG TECHNOLOGY CO.,LTD

ModelNo.:PTR5610

Productname ： BluetoothModule Modelname ： PTR5610 FCCID:2AA72-PTR5610 Companyname ： LANKEXUNTONGTECHNOLOGYCO.,LTD

Model No.: PTR5610

RFExposureEvaluationStatement ProductName: Bluetoothmodule ModelNo.：PTR5610 FCCID：2AA72-PTR5610 1.1RFExposureComplianceRequirement 1.1.1StandardRequirement AccordingtoKDB447498D01GeneralRFExposureGuidancev06 StandaloneSARtestexclusionconsiderations UnlessspecificallyrequiredbythepublishedRFexposureKDBprocedures,standalone1-gheador bodyand10-gextremitySARevaluationforgeneralpopulationexposureconditions,bymeasurementor numericalsimulation,isnotrequiredwhenthecorrespondingSARExclusionThresholdcondition,listed below,issatisfied. 1.1.2Limits The1-gand10-gSARtestexclusionthresholdsfor100MHzto6GHzattestseparationdistances ≤50mmaredeterminedby: [(max.powerofchannel,includingtune-uptolerance,mW)/(min.testseparationdistance,mm)]· [√f(GHz)]≤3.0for1-gSARand≤7.5for10-gextremitySAR,where f(GHz)istheRFchanneltransmitfrequencyinGHz PoweranddistanceareroundedtothenearestmWandmmbeforecalculation 17 Theresultisroundedtoonedecimalplaceforcomparison Thetestexclusionsareapplicableonlywhentheminimumtestseparationdistanceis≤50mmand fortransmissionfrequenciesbetween100MHzand6GHz.Whentheminimumtestseparation distanceis<5mm,adistanceof5mmisappliedtodetermineSARtestexclusion 1.1.3EUTRFExposure OperationalMode:BLE（GFSKworstcase） Channel Maximum Peak Conducted Output Power (dBm) Tuneup tolerance (dB) Maximumtune-upPower Calculated value Exclusion threshold (dBm)(mW) 2402MHZ-1.57 ±1 -0.570.880.27 3.02441MHz-2.17 ±1 -1.170.760.24 2480MHz-1.87 ±1 -0.870.820.26 Conclusion:thecalculatedvalue≤3.0,SARisexempted.

ReportNo.:BLA-EMC-202001-A06-01 BlueAsiaofTechnicalServices(Shenzhen)Co.,Ltd. IOTTestCentreofBlueAsia, No.448BulongRoad,BantianStreet,LonggangDistrict,Shenzhen,China Telephone:TEL:+86-755-28682673FAX:+86-755-28682673 FCCReport(Bluetooth) ProductName: Bluetoothmodule Trademark:XUNTONGTECH ModelNo.: PTR5610 FCCID:2AA72-PTR5610 ReportNumber:BLA-EMC-202001-A06-01 Dateofsamplereceipt:2020/1/6 DateofTest:2020/1/6–2020/1/10 DateofIssue:2020/3/3 Teststandard : FCCCFRTitle47Part15SubpartCSection 15.247 Testresult:PASS Preparedfor: LANKEXUNTONGTECHNOLOGYCO.,LTD Room7A-B,BlockBofWanlianBuilding,NetValley,No.12ofYanshan Road,Nanshandistrict,Shenzhen,China Preparedby: BlueAsiaofTechnicalServices(Shenzhen)Co.,Ltd. IOTTestCentreofBlueAsia No.448BulongRoad,BantianStreet,LonggangDistrict,Shenzhen, China TEL:+86-755-28682673 FAX:+86-755-28682673 Compileby: Reviewby: Approvedby: Date:2020/3/3 ReportNo.:BLA-EMC-202001-A06-01Page2of36 BlueAsiaofTechnicalServices(Shenzhen)Co.,Ltd. IOTTestCentreofBlueAsia, No.448BulongRoad,BantianStreet,LonggangDistrict,Shenzhen,China Telephone:TEL:+86-755-28682673FAX:+86-755-28682673 2Version VersionNo.DateDescription 002020/3/3Original ReportNo.:BLA-EMC-202001-A06-01Page3of36 BlueAsiaofTechnicalServices(Shenzhen)Co.,Ltd. IOTTestCentreofBlueAsia, No.448BulongRoad,BantianStreet,LonggangDistrict,Shenzhen,China Telephone:TEL:+86-755-28682673FAX:+86-755-28682673 3Contents Page 1COVERPAGE .......................................................................................................................................................... 1 2VERSION .................................................................................................................................................................. 2 3CONTENTS .............................................................................................................................................................. 3 4TESTSUMMARY .................................................................................................................................................... 4 5GENERALINFORMATION .................................................................................................................................... 5 5.1GENERALDESCRIPTIONOFEUT ..................................................................................................................... 5 5.2TESTMODE ....................................................................................................................................................... 7 5.3DESCRIPTIONOFSUPPORTUNITS .................................................................................................................. 7 5.4TESTFACILITY .................................................................................................................................................. 7 5.5TESTLOCATION ................................................................................................................................................ 7 6TESTINSTRUMENTSLIST .................................................................................................................................. 8 7TESTRESULTSANDMEASUREMENTDATA ............................................................................................... 10 7.1ANTENNAREQUIREMENT ................................................................................................................................ 10 7.2CONDUCTEDEMISSIONS ................................................................................................................................ 11 7.3CONDUCTEDOUTPUTPOWER ....................................................................................................................... 14 7.4CHANNELBANDWIDTH .................................................................................................................................... 16 7.5POWERSPECTRALDENSITY .......................................................................................................................... 18 7.6BANDEDGES ................................................................................................................................................... 20 7.6.1ConductedEmissionMethod ............................................................................................................. 20 7.6.2RadiatedEmissionMethod ................................................................................................................. 21 7.7SPURIOUSEMISSION ...................................................................................................................................... 23 7.7.1ConductedEmissionMethod ............................................................................................................. 23 7.7.2RadiatedEmissionMethod ................................................................................................................. 25 8TESTSETUPPHOTO .......................................................................................................................................... 33 9EUTCONSTRUCTIONALDETAILS .................................................................................................................. 35 ReportNo.:BLA-EMC-202001-A06-01Page4of36 BlueAsiaofTechnicalServices(Shenzhen)Co.,Ltd. IOTTestCentreofBlueAsia, No.448BulongRoad,BantianStreet,LonggangDistrict,Shenzhen,China Telephone:TEL:+86-755-28682673FAX:+86-755-28682673 4TestSummary TestItemSectioninCFR47Result Antennarequirement15.203/15.247(c)Pass ACPowerLineConductedEmission15.207Pass ConductedOutputPower15.247(b)(3)Pass ChannelBandwidth15.247(a)(2)Pass PowerSpectralDensity15.247(e)Pass BandEdge15.247(d)Pass SpuriousEmission15.205/15.209Pass Pass:TheEUTcomplieswiththeessentialrequirementsinthestandard. Remark:TestaccordingtoANSIC63.10:2013. MeasurementUncertainty TestItemFrequencyRangeMeasurementUncertaintyNotes RadiatedEmission9kHz~30MHz  4.34dB (1) RadiatedEm…

Text truncated - open the document above for the full version.

ModelNo.:PTR5610