2AAD3AA2G1J1Wifi Module

Doc. NO: Ability WSDB-706GN Hardware & Software Setup Guide Rev. 0.2a Doc. NO: 1 1. WLAN Function Quick Start Guide Physical hardware configuration likes as figure1. Please follow the following procedure step by step to get starting WLAN function. Software setup: Follow driver installation procedure steps to install the GB9662 driver on your PC (OS: XP).  1-1.Copy WDSB-706GN\WSDB-706GN_Driver_V1.2_10122012\Nvram\GB9662_NVRAM_V1.1_09132 012.TXT to C:\Windows\system32\Drivers 1-2. Copy WDSB-706GN\WSDB-706GN_Driver_V1.2_10122012\5_90_153_49_43362_mfg_A2(Driver)\A pps\ wl.exe to C:\Windows\system32\  1-3.In Device Manager, choose SDA Standard Compliant SD Host Controller and click right button of mouse and then choose Update driver  1-4.Choose No, not now, and then click Next. SDIO Board Test Board Socket Doc. NO: 2  1-5.Choose install from a list or specific location (Advanced), and then click Next.  1-6.Choose Don’t search, I will choose driver to install, and then click Next
. Doc. NO: 3  1-7.Click Have Disk
.  1-8.Click Browse to choose correct directory of Driver Doc. NO: 4 WDSB-706GN\WSDB-706GN_Driver_V1.2_10122012\5_90_153_49_43362_m fg_A2(Driver) \bcmsddhd.inf and then click OK
to next step.  1-9.Choose Broadcom 802.11g Network Adapter and click Next
to install driver.  1-10.Click Finish and you can check the device is working fine in Device Manager. Doc. NO: 5  1-11.In Device Manager, Choose Broadcom 802.11g Network Adapter and click right button of mouse and then choose content.  1-12.In the tab of Advanced , choose Doc. NO: 6  1-13.In the tab of Advanced , choose 43362ROMImagePatch item and replace with \SystemRoot\system32\drivers\ GB9662_NVRAM_V1.1_09132012.TXT and then click OK button. Doc. NO: 7 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intened operation as described in this Doc. NO: 8 manual.The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. F or body-worn operating conditions please use belt-clips, holsters, and/or accessories that have no metallic component in the assembly and must provide at least 0.2cm separation between the device and the user's body. This device is intended only for OEM integrators under the following conditions: 1)The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. 2) The transmitter module may not be co-located with any other transmitter or antenna. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AAD3AA2G1J1”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Doc. NO: 9 Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210…

Text truncated - open the document above for the full version.

FCC ID: 2AAD3AA2G1J1 Report No.: RF131107C07 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch December 12, 2013 Dear Application Examiner, Ability Enterprise Co., Ltd., It’s a Wifi Module, FCC ID: 2AAD3AA2G1J1 would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip BCM43362. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is BCM43362. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: 2AAD3AA2G1J1 Report No.: RF131107C07 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

Page 2

FCC ID: 2AAD3AA2G1J1 Report No.: RF131107C07 Operational Description This device is a Wifi Module, which operates in 2.4GHz band; the maximum data rate could be up to 65Mbps with OFDM technique. If the signal to noise ratio is too poor which could not support 65Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 3.3Vdc from host equipment. The antenna is Printed antenna without antenna connectors.

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 21 Report No. : SA131107C07 Issued Date : Dec. 17, 2013 Revision : R01 FCC SAR Test Report Report No. : SA131107C07 Applicant : ABILITY ENTERPRISE CO., LTD. Address : 4F., No.8, Ln. 7, Wuquan Rd., Wugu Dist., New Taipei City 248, Taiwan (R.O.C.) Product : WiFi module FCC ID : 2AAD3AA2G1J1 Brand : ABILITY Model No. : WSDB-706GN Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a-2005 / KDB 865664 D01 v01r01 KDB 248227 D01 v01r02 / KDB 447498 D01 v05r01 Sample Received Date : Nov. 07, 2013 Date of Testing : Nov. 29, 2013 ~ Dec. 16, 2013 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 21 Report No. : SA131107C07 Issued Date : Dec. 17, 2013 Revision : R01 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 12 3.4 SAR Measurement Procedure ................................................................................................................................... 13 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 13 3.4.2 Volume Scan Procedure................................................................................................................................... 13 3.4.3 Power Drift Monitoring ...................................................................................................................................... 14 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 14 3.4.5 SAR …

Text truncated - open the document above for the full version.

Report No.: RF131107C07 1 of 49 Report Format Version 5.2.0 FCC TEST REPORT REPORT NO.: RF131107C07 MODEL NO.: WSDB-706GN FCC ID: 2AAD3AA2G1J1 RECEIVED: Nov. 07, 2013 TESTED: Nov. 21 ~ Nov. 27, 2013 ISSUED: Nov. 28, 2013 APPLICANT: ABILITY ENTERPRISE CO., LTD. ADDRESS: 4F., No. 8, Ln. 7, Wuquan Rd., Wugu Dist., New Taipei City 248, Taiwan (R.O.C.) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF131107C07 2 of 49 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 4 1. CERTIFICATION ............................................................................................................ 5 2. SUMMARY OF TEST RESULTS .................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY .................................................................................. 6 3. GENERAL INFORMATION ............................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................... 7 3.2 DESCRIPTION OF TEST MODES ................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................. 9 3.3 DUTY CYCLE OF TEST SIGNAL .................................................................................. 11 3.4 DESCRIPTION OF SUPPORT UNITS ......................................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................. 13 4. TEST TYPES AND RESULTS ...................................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ....................................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................... 14 4.1.2 TEST INSTRUMENTS .................................................................................................. 15 4.1.3 TEST PROCEDURES .................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................ 16 4.1.5 TEST SETUP ................................................................................................................ 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................. 18 4.1.7 TEST RESULTS ........................................................................................................... 19 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................... 29 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................................. 29 4.2.2 TEST INSTRUMENTS .................................................................................................. 29 4.2.3 TEST PROCEDURES .................................................................................................. 30 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................ 30 4.2.5 TEST SETUP ................................................................................................................ 30 4.2.6 EUT OPERATING CONDITIONS ................................................................................. 30 4.2.7 TEST RESULTS ........................................................................................................... 31 4.3 6dB BANDWIDTH MEASUREMENT ............................................................................ 33 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ......................................................... 33 4.3.2 TEST SETUP ................................................................................................................ 33 4.3.3 TEST INSTRUMENTS .................................................................................................. 33 4.3.4 TEST PROCEDURE ...........................................................................................…

Text truncated - open the document above for the full version.

FCC SAR Test Report Report Format Version 5.0.0 Issued Date : Dec. 17, 2013 Report No. : SA131107C07 Revision : R01 Appendix D. Photographs of EUT and Setup FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131107C07 Revision : R01 <Photographs of EUT> EUT – Front View EUT – Rear View EUT Host – Front View EUT Host – Rear View FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA131107C07 Revision : R01 <Photographs of SAR Setup> Front Face of EUT with 0.2 cm Gap Rear Face of EUT with 0.2 cm Gap Left Side of EUT with 0.2 cm Gap Right Side of EUT with 0.2 cm Gap Top Side of EUT with 0.2 cm Gap Bottom Side of EUT with 0.2 cm Gap

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4