2AB9W-PP120XP3D Printer

PartPro120 xP 3D Printer (Model No. ) Operation Manual Version 2.0 Version 1.0 PartPro120 xP Operation Manual Please always refer to the updated version of PartPro120 xP operation manual https://pro.xyzprinting.com/ For safe and correct use, be sure to read the Safety Precautions before using the machine. 1 Version 1.0 PartPro120 xP Operation Manual Document History Date Description Version Editor 2019-12 Initial Release 1.0 Andy Yan i Version 1.0 PartPro120 xP Operation Manual INTRODUCTION The PartPro120 xP is a DLP 3D printer and using 3D printing (additive manufacturing) technology which utilizes led light source to cure the liquid resin to make solid parts and products. DISCLAIMER This manual is designed for users to understand how to use the PartPro120 xP printer in a safe manner. Please read through all sections especially the safety guide carefully before unpacking, operating, replacing, and removing any part of this product. INTENDED USE • User must read and understand the contents of this installation and user manual as following. Failure to read the manual may lead to personal injury, inferior results or damage to the PartPro120 xP. • Before performing any operations on the machine and/or packaging of the various parties should read this entire instruction manual. This contains important information for the safety of persons engaged in routine maintenance, the persons involved in the use and operation of the machine. • This manual refers to the machine on which the model number is indicated on the title. XYZprinting reserves the right to make technical changes on the machines and manuals without prior notice. • No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of XYZprinting. For this entire user guide, please contact authorized reseller or XYZprinting customer service for providing. • Requests for additional copies of this manual should be directed to customer service of XYZprinting. LIMITATION OF WARRANTY AND LIABILITY XYZprinting is responsible for the device in its original configuration. Any changes to the configuration of the machine must be performed or authorized by the XYZprinting technical department. XYZprinting is not responsible for the problems and warranty dues to the use of not original spare parts or printing materials. TRADEMARK All trademarks and register trademarks are the property of their respective owners. Copyright © 2019 XYZprinting, Inc. All Rights Reserved. 2 Version 1.0 PartPro120 xP Operation Manual TABLE OF CONTENTS INTRODUCTION ............................................................................................................................................... 2 DISCLAIMER ..................................................................................................................................................... 2 INTENDED USE .......................................................................................................................................................... 2 LIMITATION OF WARRANTY AND LIABILITY.............................................................................................................. 2 TRADEMARK ............................................................................................................................................................. 2 SAFETY AND COMPLIANCE ............................................................................................................................... 1 IMPORTANT SAFETY PRECAUTIONS ......................................................................................................................... 1 SAFETY AND REGULATION ........................................................................................................................................ 2 HANDLING AND OPERATING PRECAUTIONS ............................................................................................................ 2 WORK PLACE REQUIREMENTS .................................................................................................................................. 2 RECOMMENDED PROTECTIVE EQUIPMENT ............................................................................................................. 2 PRECAUTIONS BEFORE OPENING THE PROTEVTIVE COVERS ................................................................................... 2 RESIN CARE ............................................................................................................................................................... 3 RESIN TANK CARE ..................................................................................................................................................... 3 PRINTING PROCESS ................................................................................................................................................... 3 LED LIGHT ................................................................................................................................................................. 3 NOTE ON POWER SUPPLY ......................................................................................................................................... 3 1. UNPACKING AND INSTALLATIONS ................................................................................................................. 4 UNPACKING .............................................................................................................................................................. 4 HARDWARE INSTALLATION ...................................................................................................................................... 5 SOFTWARE INSTALLATION........................................................................................................................................ 7 2. PROD…

Text truncated - open the document above for the full version.

Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 1 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 2 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 3 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 4 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 5 of 24 FSP / FSP120-AAAN3 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 6 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 7 of 24

Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 8 of 24 WIFI antenna Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 9 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 10 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 11 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 12 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 13 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 14 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 15 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 16 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 17 of 24 WIFI antenna Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 18 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 19 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 20 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 21 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 22 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 23 of 24 Appendix No.: EP-1911T047-1 APPENDIX-EUT PHOTOS Project No.: 1911T047 Page 24 of 24 NFC antenna

Report No.: BTL-FCCP-3-1911T047 Project No.: 1911T047 Page 1 of 4 Report Version: R00 Maximum Permissible Exposure Report FCC ID: 2AB9W-PP120XP Report No. : BTL-FCCP-3-1911T047 Equipment : 3D Printer Model Name : PartPro120 xP Brand Name : XYZprinting Applicant : XYZprinting, Inc. Address : 10F., No.99, Sec. 5, Nanjing E. Rd.,Songshan Dist., Taipei City 10571, Taiwan (R.O.C.) Manufacturer : Cal-Comp Electronics (Thailand) Public Company Limited Address : 138, Moo 4, Phechkasem Road, Sapang, Koawyoi, Petchaburi 76140, Thailand. Factory : Cal-Comp Electronics (Thailand) Public Company Limited Address : 138, Moo 4, Phechkasem Road, Sapang, Koawyoi, Petchaburi 76140, Thailand. FCC Rule Part(s) : FCC Guidelines for Human Exposure IEEE C95.1 Date of Receipt : 2019/11/27 Date of Test : 2019/11/27 ~ 2019/12/30 Issued Date : 2020/1/8 The above equipment has been tested and found in compliance with the requirement of the above standards by BTL Inc. Prepared by : Peter Chen, Engineer Approved by : Scott Hsu, Manager BTL Inc. No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City 114, Taiwan Tel: +886-2-2657-3299 Fax: +886-2-2657-3331 Web: www.newbtl.com Report No.: BTL-FCCP-3-1911T047 Project No.: 1911T047 Page 2 of 4 Report Version: R00 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue. 2020/1/8 Report No.: BTL-FCCP-3-1911T047 Project No.: 1911T047 Page 3 of 4 Report Version: R00 MPE CALCULATION METHOD: Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 N/A N/A PCB N/A -8.65 TEST RESULTS For WLAN: Antenna Gain (dBi) Antenna Gain (numeric) Max. Average Output Power (dBm) Max. Average Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result -8.65 0.1365 13 19.9526 0.0005 1 Complies Note: The calculated distance is 20 cm. Report No.: BTL-FCCP-3-1911T047 Project No.: 1911T047 Page 4 of 4 Report Version: R00 For NFC: Max H-field strength (dBuV/m) E-field strength (V/m) Limit 38.46 0.00008 60.77 COLLOCATED POWER DENSITY CACULATIONS So for NFC+2.4G simultaneous transmission 0.00008/60.77+0.0005/1=0.0005<1 End of Test Report

Report No.: BTL-FCCP-1-1911T047 Project No.: 1911T047 Page 1 of 73 Report Version: R00 FCC Radio Test Report FCC ID: 2AB9W-PP120XP Prepared by : Peter Chen, Engineer Approved by : Scott Hsu , Manager BTL Inc. No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City 114, Taiwan Tel: +886-2-2657-3299 Fax: +886-2-2657-3331 Web: www.newbtl.com Report No. : BTL-FCCP-1-1911T047 Equipment : 3D Printer Model Name : PartPro120 xP Brand Name : XYZprinting Applicant : XYZprinting, Inc. Address : 10F., No.99, Sec. 5, Nanjing E. Rd.,Songshan Dist., Taipei City 10571, Taiwan (R.O.C.) Manufacturer : Cal-Comp Electronics (Thailand) Public Company Limited Address : 138, Moo 4, Phechkasem Road, Sapang, Koawyoi, Petchaburi 76140, Thailand. Factory : Cal-Comp Electronics (Thailand) Public Company Limited Address : 138, Moo 4, Phechkasem Road, Sapang, Koawyoi, Petchaburi 76140, Thailand. Radio Function : WLAN 2.4 GHz FCC Rule Part(s) Measurement Procedure(s) : FCC Part15, Subpart C (15.247) : ANSI C63.10-2013 Date of Receipt : 2019/11/27 Date of Test : 2019/11/27 ~ 2019/12/30 Issued Date : 2020/1/8 The above equipment has been tested and found in compliance with the requirement of the above standards by BTL Inc. Report No.: BTL-FCCP-1-1911T047 Project No.: 1911T047 Page 2 of 73 Report Version: R00 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. The report must not be used by the client to claim product certification, approval, or endorsement by NIST, A2LA, or any agency of the U.S. Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO/IEC 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Report No.: BTL-FCCP-1-1911T047 Project No.: 1911T047 Page 3 of 73 Report Version: R00 CONTENTS REPORT ISSUED HISTORY 5 1 SUMMARY OF TEST RESULTS 6 1.1 TEST FACILITY 7 1.2 MEASUREMENT UNCERTAINTY 7 1.3 TEST ENVIRONMENT CONDITIONS 8 1.4 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 8 1.5 DUTY CYCLE 9 2 GENERAL INFORMATION 10 2.1 DESCRIPTION OF EUT 10 2.2 TEST MODES 11 2.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 12 2.4 SUPPORT UNITS 12 3 AC POWER LINE CONDUCTED EMISSIONS TEST 13 3.1 LIMIT 13 3.2 TEST PROCEDURE 13 3.3 DEVIATION FROM TEST STANDARD 13 3.4 TEST SETUP 14 3.5 TEST RESULT 14 4 RADIATED EMISSIONS TEST 15 4.1 LIMIT 15 4.2 TEST PROCEDURE 16 4.3 DEVIATION FROM TEST STANDARD 16 4.4 TEST SETUP 16 4.5 EUT OPERATING CONDITIONS 17 4.6 TEST RESULT – 9 KHZ TO 30 MHZ 18 4.7 TEST RESULT – 30 MHZ TO 1 GHZ 18 4.8 TEST RESULT – ABOVE 1 GHZ 18 5 BANDWIDTH TEST 19 5.1 LIMIT 19 5.2 TEST PROCEDURE 19 5.3 DEVIATION FROM TEST STANDARD 19 5.4 TEST SETUP 19 5.5 EUT OPERATING CONDITIONS 19 5.6 TEST RESULT 19 6 OUTPUT POWER TEST 20 6.1 LIMIT 20 6.2 TEST PROCEDURE 20 6.3 DEVIATION FROM TEST STANDARD 20 6.4 TEST SETUP 20 6.5 EUT OPERATING CONDITIONS 20 6.6 TEST RESULT 20 7 POWER SPECTRAL DENSITY 21 7.1 LIMIT 21 7.2 TEST PROCEDURE 21 7.3 DEVIATION FROM TEST STANDARD 21 7.4 TEST SETUP 21 7.5 EUT OPERATING CONDITIONS 21 7.6 TEST RESULT 21 Report No.: BTL-FCCP-1-1911T047 Project No.: 1911T047 Page 4 of 73 Report Version: R00 8 ANTENNA CONDUCTED SPURIOUS EMISSIONS TEST 22 8.1 LIMIT 22 8.2 TEST PROCEDURE 22 8.3 DEVIATION FROM TEST STANDARD 22 8.4 TEST SETUP 22 8.5 EUT OPERATING CONDITIONS 22 8.6 TEST RESULT 22 9 LIST OF MEASURING EQUIPMENTS 23 10 EUT TEST PHOTO 25 11 EUT PHOTOS 25 APPENDIX A AC POWER LINE CONDUCTED EMISSIONS 26 APPENDIX B RADIATED EMISSIONS - 9 KHZ TO 30 MHZ 29 APPENDIX C RADIATED EMISSIONS - 30 MHZ TO 1 GHZ 34 APPENDIX D RADIATED EMISSIONS - ABOVE 1 GHZ 37 APPENDIX E BANDWIDTH 62 APPENDIX F OUTPUT POWER 65 APPENDIX G POWER SPECTRAL DENSITY 67 APPENDIX H ANTENNA CONDUCTED SPURIOUS EMISSIONS 70 Report No.: BTL-FCCP-1-1911T047 Project No.: 1911T047 Page 5 of 73 Report Version: R00 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue. 2020/1/8 Report No.: BTL-FCCP-1-1911T047 Project No.: 1911T047 Page 6 of 73 Report Version: R00 1 SUMMARY OF TEST RESULTS Test procedures according to the technical standards. FCC Part 15, Subpart C (15.247) Standard(s) Section Description Test Result Judgement Remark 15.207 AC Power Line Conducted Emissions APPENDIX A Pass ------ 15.205 15.209 15.247(d) Radiated Emissions APPENDIX B APPENDIX C APPENDIX D Pass ------ 15.247(a) Bandwidth APPENDIX E Pass ------ 15.247(b) Output Power APPENDIX F Pass ------ 15.247(e) Power Spectral Density APPENDIX G Pass -…

Text truncated - open the document above for the full version.

Appendix No.: TP-1911T047-FCCP-1 APPENDIX-TEST PHOTOS Project No.: 1911T047 Page 1 of 4 AC Power Line Conducted Emissions test photos Appendix No.: TP-1911T047-FCCP-1 APPENDIX-TEST PHOTOS Project No.: 1911T047 Page 2 of 4 Radiated emissions test photos 9 kHz to 30 MHz Appendix No.: TP-1911T047-FCCP-1 APPENDIX-TEST PHOTOS Project No.: 1911T047 Page 3 of 4 Radiated emissions test photos 30 MHz to 1 GHz Appendix No.: TP-1911T047-FCCP-1 APPENDIX-TEST PHOTOS Project No.: 1911T047 Page 4 of 4 Radiated emissions test photos Above 1 GHz