2ABDZ61HD13DWS02791Full HD Golf Camcorder

0 1 Contents 1. Precautions 2 2. Preparation 4  Standard Accessories 4  Part Names 5  Installing the Battery Pack 6  Charging the Battery Pack 7  Battery Power Status 8  Assembling the SwingShot ® Camcorder 9 3. Quick Start 10  Insert Memory Card 10  Power ON 11  Power OFF 11 4. Modes Settings 12  TEST Mode 12  LESSON Mode 14  RANGE Mode 15  COURSE Mode 16  SCENIC Mode 17 5. Wireless 18  Initiate Wireless Function18 6. Playback 19  Playback from PC / Mac 19 7. Appendix 20  Specifications 20  System Requirement 21 2 Introduction Thank you for choosing the SwingShot Camcorder to record your on-course golf videos. Whether you are analyzing your golf swing, recording a lesson, or simply capturing memories of your favorite golf moments with friends and family, to get the utmost satisfaction from your SwingShot Camcorder, you will want to take a moment to read through this manual which explains your camera's many features. 1. Precaution Before using the SwingShot Camcorder, please ensure that you read and understand the safety precautions described below. Always ensure that the camera is operated correctly. • Never operate the camcorder inside of an aircraft or anywhere else where operation of such devices is restricted. Improper use creates the risk of a serious accident. • Do not try to open the housing of the camcorder or attempt to modify this camcorder in any way. High-voltage internal components create the risk of electric shock when exposed. Only authorized service providers should open the housing. • Do not submerge the camcorder in water and other liquids. Excessive moisture creates the danger of fire and electric shock. • Keep the camcorder and its accessories out of the reach of children and animals to prevent accidental or damage to the camcorder. 3 • Use only the official SwingShot power accessories. Use of power sources not expressly designed for this equipment will void the warranty and may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards. • Never use a dirty or course cloth or apply too much force when cleaning the surface of the lens to avoid scratches on the lens surface. • The camcorder may become slightly warm during use. This is normal. • Turn the camcorder off when not in use. If battery is totally drained it may be difficult to recharge in camera and may need to be recharged in an external wall charger or may need to be replaced entirely. • Please remove battery from camera during long periods of inactivity. • If the exterior of the camcorder needs cleaning, wipe it with a soft, dry cloth. • If there is leaking, discoloration, change of shape, excessive rise in temperature, damaged exterior, strange odor or any other abnormal condition, immediately discontinue use and remove the battery pack from the camcorder, taking care to keep it well away from fire. • If you notice smoke or a strange odor coming from the camcorder, turn the power off immediately. Take the camcorder to the nearest authorized service center for repair. Never attempt to repair the camcorder on your own. 4 2. Preparation Standard Accessories Camcorder Li-ion Battery User Manual microSD Card Battery Charger AC Adaptor Camera Holder Shaft Joint Shaft x2 Spike 5 Part Names 6 Installing the Battery Pack 1. Open the battery compartment cover by lightly pressing and sliding it toward the edge. 2. Insert the supplied battery. Make sure the ends (+ and -) of the battery are matching to the polarities indicated in the battery compartment. 3. Snap the cover back into place. 7 Charging the Battery Pack The battery pack is not fully charged at the time of purchase and therefore the battery needs to be fully charged for 4 hours before use. If the battery charge becomes low while you are using the camera, recharge it as soon as possible. 1. Open the battery compartment cover by lightly pressing and sliding it toward the edge. 2. Take out the battery pack from the SwingShot Camcorder. 3. Insert the battery pack into the supplied battery charger, pay attention to the indicated polarity (+ and -). 8 4. Plug the mini USB end of the supplied AC adaptor to the mini USB port of the battery charger and plug the adaptor into the power outlet. 5. The red charge LED of the battery charger illuminate. 6. The red LED turn off and the green ready LED illuminate when the battery has full charged. 7. Take off the battery from the charger and insert it back to the SwingShot Camcorder. Battery Power Status Full 2/3 1/3 Empty 9 Assemble the SwingShot Camcorder Assemble each part by carefully screwing the threads in a clockwise direction (to the right) until tight. Using excessive force will damage the threads. 10 3. Quick Start Insert Memory Card 1. Make sure the SwingShot Camcorder is power off before insert the memory card. 2. Insert the compatible microSDHC card into the SD card slot. Press it to the end and make sure it was locked. 3. If the memory card is not compatible or defected. The memory card error icon will show on the screen. Please remove it and insert another card. 4. Replace a new memory card when the current card was full. 11 Power ON 1. Press and hold the POWER button. The LED will light up and then turn off. 2. Release the POWER button when the LCD turns on indicating the SwingShot Camcorder is on. 3. When the LCD Monitor has been activated, the SwingShot Camcorder is ready to use. Power OFF 1. Press and hold the POWER button. Release it when the LCD turns off indicating the SwingShot Camcorder is off. 2. To conserve power, the SwingShot Camcorder will turn off the LCD automatically after 8 seconds of inactivity. The LED will still blink slowly indicating the power is still on. Quickly press REC button to wake up the SwingShot Camcorder. 12 4. Modes Settings TEST Mode It’s recommended you use the TEST mode the first time you use the SwingShot Camcorder. It will help you to confirm all camera functions are normal. Resolution: 1080p / 60 fps GPS: Enabled Timer:…

Text truncated - open the document above for the full version.

詠業科技股份有限公司 Unictron Technologies Corporation Website:www.unictron.com THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF UNICTRON TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION Prepared by : Nacy Designed by : Jason Checked by : Jason Approved by：Herbert UNIT：mm DOCUMENT REV. TITLE：50 x 5.0 x 0.5 (mm) WiFi PCB Substrate Antenna(L=50mm) Engineering Specification NO. H2B1BE1A1B1300 A PAGE 1 OF 5 H 2 1B EAB3 0B1 (1) (2) (3) (4) (5) 110 50 x 5.0 x 0.5 (mm) WiFi PCB Substrate Antenna (L=50mm) Engineering Specification 1. Explanation of Product Number Product Code: (1) Product Categories: B: polymer substrate antenna (2) Dimensions: E1: 50 x 5.0 x 0.5(mm) (3) Material: A: GF (4) Working Frequencies 1B: 2400~2500 MHz (5) Antenna Series: 13: serial number (IPEX I Compatible, L=50mm, Tape: 3M#1600SB) 詠業科技股份有限公司 Unictron Technologies Corporation Website:www.unictron.com THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF UNICTRON TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION Prepared by : Nacy Designed by : Jason Checked by : Jason Approved by：Herbert UNIT：mm DOCUMENT REV. TITLE：50 x 5.0 x 0.5 (mm) WiFi PCB Substrate Antenna(L=50mm) Engineering Specification NO. H2B1BE1A1B1300 A PAGE 2 OF 5 2. Features *Stable and reliable in performances *Compact size *RoHS compliance 3. Applications * IEEE802.11 (b/g/n). * Hand-held devices when WiFi (802.11 b/g/n) functions are needed. 4. Description Unictron’s PCB antenna series are specially designed for WiFi (802.11 b/g/n) applications. Based on Unictron’s proprietary design and processes, this PCB antenna has excellent stability and sensitivity to consistently provide high signal reception efficiency. 5. Electrical Specifications 5-1. Electrical Table: Characteristics Specifications Unit Outline Dimensions 50 x 5.0 x 0.5 mm Working Frequency* 2400~2500 MHz Bandwidth 100 min. MHz VSWR 2 max. Impedance 50 Ω Polarization Linear Polarization Peak 3.3 (typical) dBi Gain Efficiency 76 (typical) % Note： * Working frequency will be offset to another frequency according to the conditions of user’s ground plane and radome. 詠業科技股份有限公司 Unictron Technologies Corporation Website:www.unictron.com THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF UNICTRON TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION Prepared by : Nacy Designed by : Jason Checked by : Jason Approved by：Herbert UNIT：mm DOCUMENT REV. TITLE：50 x 5.0 x 0.5 (mm) WiFi PCB Substrate Antenna(L=50mm) Engineering Specification NO. H2B1BE1A1B1300 A PAGE 3 OF 5 5-2. Return Loss & Smith Chart Return Loss (S 11 ) Smith Chart (S 11 ) 6. Antenna Dimensions : (unit: mm) 詠業科技股份有限公司 Unictron Technologies Corporation Website:www.unictron.com THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF UNICTRON TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION Prepared by : Nacy Designed by : Jason Checked by : Jason Approved by：Herbert UNIT：mm DOCUMENT REV. TITLE：50 x 5.0 x 0.5 (mm) WiFi PCB Substrate Antenna(L=50mm) Engineering Specification NO. H2B1BE1A1B1300 A PAGE 4 OF 5 7. Radiation Pattern 7-1. 3D Gain Pattern (Radiation Pattern @ 2442 MHz) Y X Z X Y Z Y X Z Y Z X 詠業科技股份有限公司 Unictron Technologies Corporation Website:www.unictron.com THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF UNICTRON TECHNOLOGIES CORPORATION AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION Prepared by : Nacy Designed by : Jason Checked by : Jason Approved by：Herbert UNIT：mm DOCUMENT REV. TITLE：50 x 5.0 x 0.5 (mm) WiFi PCB Substrate Antenna(L=50mm) Engineering Specification NO. H2B1BE1A1B1300 A PAGE 5 OF 5 7-2. 3D Efficiency Table Frequency(GHz) 2.400 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484 Efficiency(dB) -1.58 -1.21 -1.24 -1.27 -1.25 -1.21 -1.14 -1.16 -1.14 -1.10 -1.04 -1.01 -0.87 -0.80 -0.86 Efficiency(%) 69.50 75.68 75.16 74.64 74.99 75.68 76.91 76.56 76.91 77.62 78.70 79.25 81.85 83.18 82.04 Gain(dBi) 2.81 3.20 3.18 3.17 3.21 3.22 3.35 3.39 3.48 3.60 3.66 3.73 4.02 4.13 4.06 7-3. 3D Efficiency vs. Frequency Efficiency vs. Frequency 50.00 60.00 70.00 80.00 90.00 2.400 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484 Frequency(GHz) Efficiency(%)

RF_160, Issue 03 Declaration of Authorization We Name: < SALIX TECHNOLOGY CO., LTD. > Address: 5F, NO. 16, LANE 77, HSING AI RD., NEI-HU City: TAIPEI Country: Taiwan Declare that: Name Representative of agent: Willis Chen (1) Agent Company name: SGS Taiwan Ltd. Address: 134, Wu Kung Rd., Wuku Industrial Zone City: New Taipei City Country Taiwan is authorized to apply for Certification of the following product(s): Product description: Full HD Golf Camcorder Type designation: HD-13DW, SS-5 Trademark: N/A on our behalf. Date: Feb. 25, 2014 City: Taipei Name: Mr. David Lee (2) Function: Engineer Signature: Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

DECLARATION OF CONFORMITY (DoC) Equipment: Full HD Golf Camcorder Trademark(s) and Model(s): NA/ HD-13DW, SS-5 Manufacturer: SALIX TECHNOLOGY CO., LTD. FCC ID in case other parts of this equipment are subject to certification: 2ABDZ61HD13DWS02791 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration: Test report number:E1/2013/B0034 Issue date:2014-03-20 Company name: SALIX TECHNOLOGY CO., LTD. Name/Title (legal representative): David Lee/ Engineer Address: 5F, NO. 16, LANE 77, HSING AI RD., NEI-HU, TAIPEI 114, TAIWAN Phone: 886-2-27921512 Fax: 886-2-27921526 E-mail: [email protected] Date: 2014-03-24 Signature: Test Lab: SGS Taiwan Ltd. No. 134, Wu Kung Road, New Taipei Industrial Park, Wu Ku District, New Taipei City, 24803, Taiwan (R.O.C)

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: SALIX TECHNOLOGY CO., LTD. Address : 5F, NO. 16, LANE 77, HSING AI RD., NEI-HU City: TAIPEI Country: TAIWAN To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2ABDZ61HD13DWS02791 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: In order to ensure sensitive business information remains confidential until the actual marketing of the device. Planned Release Date STC: 180 days (notes 2, 3, 4, 5) Date: Feb. 25, 2014 Name and signature of applicant: Mr David Lee/ Engineer Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group APPENDIX 2 EXTERNAL PHOTOGRAPHS OF EUT Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group All View of EUT Front View of EUT Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group Back View of EUT Side View of EUT – 1 Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipei…

Text truncated - open the document above for the full version.

Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group APPENDIX 2 INTERNAL PHOTOGRAPHS OF EUT Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group Open View of EUT – 1 Open View of EUT – 2 Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group Open View of EUT – 3 Open View of EUT – 4 Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistri…

Text truncated - open the document above for the full version.

Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/北北路134 t (8862) 22993279 f (8862) 22980488 www.tw.sgs.com Member of SGS Group 13 MAXIMUM PERMISSIBLE EXPOSURE (MPE) 13.1 Standard Applicable According to 1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Com- mission’s guideline. This is a Mobile device, the MPE is required. According to 1.1310 and 2.1093 RF exposure is calculated. Limits for Maximum Permissive Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minute) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / F/1500 30 1500-15000 / / 1.0 30 F = frequency in MHz * = Plane-wave equipment power density Report No.: E2/2013/B0028 FCC ID: 2ABDZ61HD13DWS02791 Issue Date: Feb. 21, 2014 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 說留不 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except…

Text truncated - open the document above for the full version.