2ABGW-AL2206NMID

MID AL2206N MID FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC RF warning statement: the device has been evaluated to meet general RF exposure requirement , The device can be used in portable exposure condition without restriction.

Hong Kong Topsky Technology Limited Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2013-12-19 SUBJECT: FCC Application for (FCC ID: 2ABGW-AL2206N) To Whom It May Concern: We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. We understand that devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm Select the "accredited" option to search for FCC recognized accredited test firms. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. Regards, Signatory Signature Date:2013/12/19 Name: Alex Zhao Title: EM Add: Unit 5, 27/F., Richmond Commercial Building, 109 Argyle Street, Mongkok, Kowloon, Hong Kong

Hong Kong Topsky Technology Limited Model Difference FCC ID: 2ABGW-AL2206N Model : AL2206N, TS779 All models are identical except model names. Regards, Client’s signature Name: Alex Zhao Title : EM Address: Unit 5, 27/F., Richmond Commercial Building, 109 Argyle Street, Mongkok, Kowloon, Hong Kong

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 Hong Kong Topsky Technology Limited SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 2013/12/21 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We,Hong Kong Topsky Technology Limited hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product： MID Trade Name： N/A Model Name： AL2206N Serial Model： TS779 FCC ID： 2ABGW-AL2206N We affirm that between SIEMIC and ___ Hong Kong Topsky Technology Limited ____ , any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature Signature Name: Alex Zhao Title: EM Tel: 0755-61156511

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Hong Kong Topsky Technology Limited 2013-12-21 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2ABGW-AL2206N We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Signature Name: Alex Zhao Title: EM Address: Unit 5, 27/F., Richmond Commercial Building, 109 Argyle Street, Mongkok, Kowloon, Hong Kong

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

FCC ID LABELING AND LOCATION FCC ID Label MID Model NO.: AL2206N Input Rating: DC 5V/ 1500mA FCC ID: 2ABGW-AL2206N Hong Kong Topsky Technology Limited Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 BT&WIFI ANT Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8

RF EXPOSURE EVALUATION METHOD FCC ID: 2ABGW-AL2206N SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Maximum measured transmitter power. WIFI: TX 802.11b Mode Frequency Maximum Conducted Output Power(PK) Maximum Conducted Output Power(AV) Maximum Conducted Output Power（AV） Te s t Channe (MHz) (dBm) (dBm) mW CH01 2412 12.68 9.30 8.51 CH06 2437 12.53 9.32 8.55 CH11 2462 12.56 9.47 8.85 TX 802.11g Mode CH01 2412 11.45 8.64 7.31 CH06 2437 11.62 8.51 7.10 CH11 2462 11.66 8.27 6.71 TX 802.11n-HT20 Mode CH01 2412 10.43 8.43 6.97 CH06 2437 10.52 8.25 6.68 CH11 2462 10.65 8.36 6.85 BT: 1Mbps Test Channel Frequency (MHz) Peak Output Power (dBm) Maximum Conducted Output Power（AV）mW CH00 2402 -5.795 0.26 CH39 2441 -5.071 0.31 CH78 2480 -4.491 0.36 2Mbps CH00 2402 -5.101 0.31 CH39 2441 -4.496 0.36 CH78 2480 -3.921 0.41 3Mbps CH00 2402 -5.053 0.31 CH39 2441 -4.406 0.36 CH78 2480 -3.792 0.42 Remark: The best case gain of the antenna is 1.0dBi. 1.0 dBi logarithmic terms convert to numeric result is nearly 1.58 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)] WIFI: Mode [(max. power of channel, including tune-up tolerance, mW) (min. test separation distance,mm)] [√f(GHz)] Result Limit 802.11b CH01 8.51 5 2.412 2.64 3 CH06 8.55 5 2.437 2.67 3 CH11 8.85 5 2.462 2.79 3 802.11g CH01 7.31 5 2.412 2.27 3 CH06 7.10 5 2.437 2.22 3 CH11 6.71 5 2.462 2.11 3 802.11n(20) CH01 6.97 5 2.412 2.16 3 CH06 6.68 5 2.437 2.09 3 CH11 6.85 5 2.462 2.16 3 BT: Mode [(max. power of channel, including tune-up tolerance, mW) (min. test separation distance,mm)] [√f(GHz)] Result Limit 1Mbps CH00 0.26 5 2.412 0.08 3 CH39 0.31 5 2.437 0.10 3 CH78 0.36 5 2.462 0.11 3 2Mbps CH00 0.31 5 2.412 0.10 3 CH39 0.36 5 2.437 0.11 3 CH78 0.41 5 2.462 0.13 3 3Mbps CH00 0.31 5 2.412 0.10 3 CH39 0.36 5 2.437 0.11 3 CH78 0.42 5 2.462 0.13 3 The test Result is less than 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Conclusion: No SAR is required. 

FCC RADIO TEST REPORT FCC ID: 2ABGW-AL2206N Product： MID Trade Name： N/A Model Name： AL2206N Serial Model： TS779 Report No.： NTEK-2013NT1128646F1 Prepared for Hong Kong Topsky Technology Limited Unit 5, 27/F., Richmond Commercial Building, 109 Argyle Street, Mongkok, Kowloon, Hong Kong Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 56 Report No.: NTEK-2013NT1128646F1 TEST RESULT CERTIFICATION Applicant’s name........ Hong Kong Topsky Technology Limited Address ........................ Unit 5, 27/F., Richmond Commercial Building, 109 Argyle Street, Mongkok, Kowloon, Hong Kong Manufacture's Name... Hong Kong Topsky Technology Limited Address ........................ Unit 5, 27/F., Richmond Commercial Building, 109 Argyle Street, Mongkok, Kowloon, Hong Kong Product description Product name .................MID Model and/or type reference ..................... AL2206N Serial Model .................... TS779 Standards.................... FCC Part15.247 Test procedure ................ ANSI C63.4-2003 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test...................................... Date (s) of performance of tests ....... 28 Nov. 2013 ~18 Dec. 2013 Date of Issue..................................... 18 Dec. 2013 Test Result......................................... Pass Testing Engineer : (Apple Huang) Technical Manager : (Brown Lu) Authorized Signatory : (Bovey Yang) Page 3 of 56 Report No.: NTEK-2013NT1128646F1 Table of Contents Page 1 . SUMMARY OF TEST RESULTS 3 1.1 TEST FACILITY 3 1.2 MEASUREMENT UNCERTAINTY 3 2 . GENERAL INFORMATION 3 2.1 GENERAL DESCRIPTION OF EUT 3 2.2 DESCRIPTION OF TEST MODES 3 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 3 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 3 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 3 3 . EMC EMISSION TEST 3 3.1 CONDUCTED EMISSION MEASUREMENT 3 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 3 3.1.2 TEST PROCEDURE 3 3.1.3 DEVIATION FROM TEST STANDARD 3 3.1.4 TEST SETUP 3 3.1.5 EUT OPERATING CONDITIONS 3 3.1.6 TEST RESULTS 3 3.2 RADIATED EMISSION MEASUREMENT 3 3.2.1 RADIATED EMISSION LIMITS 3 3.2.2 TEST PROCEDURE 3 3.2.3 DEVIATION FROM TEST STANDARD 3 3.2.4 TEST SETUP 3 3.2.5 EUT OPERATING CONDITIONS 3 3.2.6 TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 3 3.2.7 TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 3 3.2.8 TEST RESULTS (ABOVE 1000 MHZ) 3 4 . POWER SPECTRAL DENSITY TEST 3 4.1 APPLIED PROCEDURES / LIMIT 3 4.1.1 TEST PROCEDURE 3 4.1.2 DEVIATION FROM STANDARD 3 4.1.3 TEST SETUP 3 4.1.4 EUT OPERATION CONDITIONS 3 4.1.5 TEST RESULTS 3 5 . BANDWIDTH TEST 3 5.1 APPLIED PROCEDURES / LIMIT 3 5.1.1 TEST PROCEDURE 3 Page 4 of 56 Report No.: NTEK-2013NT1128646F1 Table of Contents Page 5.1.2 EUT OPERATION CONDITIONS 3 5.1.3 TEST RESULTS 3 6 . PEAK OUTPUT POWER TEST 3 6.1 APPLIED PROCEDURES / LIMIT 3 6.1.1 TEST PROCEDURE 3 6.1.2 DEVIATION FROM STANDARD 3 6.1.3 TEST SETUP 3 6.1.4 EUT OPERATION CONDITIONS 3 6.1.5 TEST RESULTS 3 7 . 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE 3 7.1 DEVIATION FROM STANDARD 3 7.2 TEST SETUP 3 7.3 EUT OPERATION CONDITIONS 3 7.4 TEST RESULTS 3 8 . ANTENNA REQUIREMENT 3 8.1 STANDARD REQUIREMENT 3 8.2 EUT ANTENNA 3 9 . EUT TEST PHOTO 3 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 56 Report No.: NTEK-2013NT1128646F1 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247 (a)(2) 6dB Bandwidth PASS 15.247 (b) Peak Output Power PASS 15.247 (c) Radiated Spurious Emission PASS 15.247 (d) Power Spectral Density PASS 15.205 Band Edge Emission PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Page 6 of 56 Report No.: NTEK-2013NT1128646F1 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add.:1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 56 Report No.: NTEK-2013NT1128646F1 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment MID Trade Name N/A Model Name AL2206N Serial Model TS779 Model Difference All models are identical except model names. Product Description The EUT is a MID Operation Frequency: 802.11b/g/n(20MHz):2412~2462 MHz Modulation Type: CCK/OFDM/DBPSK/DAPSK Bit Rate of Transmitter 802.11b:11/5.5/2/1 Mbps 802.11g:54/48/36/24/18/12/9/6Mbps 802.11n(20MHz):150/144.44/130/117/ 115.56/104/86.67/78/52/6.5Mbps Number Of Channel 802.11b/g/n20MHz:11CH Antenna Designation: Please see Note 3. Output MAX Peak Power(Conducted): 802.11b: 12.68 dBm (Max.) 802.11g: 11.66 dBm (Max.) 802.11n(20M): 10.65 dBm (Max.) Antenna Gain (dBi) 1.0dbi Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the U…

Text truncated - open the document above for the full version.

Page 75 of 76 Report No.: NTEK-2013NT1128646F2 11. EUT TEST PHOTO Radiated Measurement Photos Page 76 of 76 Report No.: NTEK-2013NT1128646F2 CONDUCTED EMISSION Photo