2ABXRBVMCN5111Bluetooth Low Energy Module

User Manual Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). The following information must be indicated on the host device of this module; [for FCC] Contains Transmitter Module FCC ID: 2ABXRBVMCN5111 or Contains FCC ID: 2ABXRBVMCN5111 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. *If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. [for IC] Contains Transmitter Module IC: 12340A-BVMCN5111 or C o n t a i n s I C : 12340A-BVMCN5111 The following statements must be described on the user manual of the vehicle; [for FCC] FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. When installing in Mobile device This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). When installing in Portable device This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). *Portable device: Distance between the person’s body and the antenna is 20cm or less. *Mobile device: Distance between the person’s body and the antenna is more than 20cm. [for IC] This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. When installing in Mobile device This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. When installing in Portable device This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation du débit d’absorption spécifique (DAS). *Portable device: Distance between the person’s body and the antenna is 20cm or less. *Mobile device: Distance between the person’s body and the antenna is more than 20cm.

PRODUCT PICTURE (Shielded) Soldering Point RIGHT FRONTTOPBACK LEFT BOTTOM

3 Certification Label Shield case This module is small so there is no space FCCID written by one line This module is small so there is no space IC written by one line Printed the Model No. by Silk printing C 2314 B A D E F Application drawing 14/10/14 14/10/14 14/10/14Yoshida Yoshida Tomiyoshi WEIGHT: - - - A4 SHEET 1 OF 1 SCALE:5:1 PARTS NO. TITLE: REVISION DO NOT SCALE DRAWING MATERIAL: DATESIGNATURENAME DEBUR AND BREAK SHARP EDGES R=0.5 FINISH: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: Q.A MFG APPV'D CHK'D DRAWN MODEL: BVMCN5111 BVMCN5111 VIEW: UNLESS OTHERWISE SPECIFIED LINEAR Classification 0.4≦ｘ≦3 3＜ｘ≦6 6＜ｘ≦30 30＜ｘ≦120 120＜ｘ≦400 400＜ｘ≦1000 1000＜ｘ≦2000 2000＜ｘ≦4000 Tolerance ±0.05 ±0.1 ±0.1 ±0.2 ±0.2 ±0.3 ±0.5 - - - - -

PRODUCT PICTURE (Unshielded) RIGHT FRONTBACK TOP LEFT BOTTOM

UL Japan, Inc. Ise EMC Lab 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan T:: +81.596.24.8999 / F:: +81.596.24.8124 / W:: ul.com/jp September 25, 2014 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID: 2ABXRBVMCN5111 To whom it may concern, We, UL Japan, Inc, hereby declare that Bluetooth Low Energy Module, model: BVMCN5111 (FCC ID: 2ABXRBVMCN5111) of Braveridge Co., Ltd. is exempt from RF exposure SAR evaluation as its output power meets the exclusion limits stated in KDB 447498D01(V05). KDB 447498D01(V05) has the following exclusion for portable devices: The 1g and 10g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where •f(GHz) is the RF channel transmit frequency in GHz •Power and distance are rounded to the nearest mW and mm before calculation •The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. This device has f = 2.48 GHz and distance = 5 mm (minimum separation distance: 5 mm was used in the calculation) and the maximum tune-up tolerance limit was 3 mW (Output power in Theory of Operation) So for this device: 3 mW[maximum tune-up tolerance limit]/5 mm[minimum separation distance]*√2.48 = 0.9 *This is less than 3.0, so no SAR is required. Thank you for your attention to this matter. Takayuki Shimada Engineer of Ise EMC Lab. Consumer Technology Division UL Japan, Inc.

Test report No. : 10478909H-B Page : 2 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 10478909H-B Revision Test report No. Date Page revised Contents - (Original) 10478909H-B September 25, 2014 - - Test report No. : 10478909H-B Page : 3 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 4 SECTION 3: Test specification, procedures & results ............................................................................ 5 SECTION 4: Operation of E.U.T. during testing .................................................................................... 8 SECTION 5: Conducted Emission .......................................................................................................... 10 SECTION 6: Radiated Spurious Emission ............................................................................................ 11 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 12 APPENDIX 1: Data of EMI test .............................................................................................................. 13 Conducted Emission ......................................................................................................................... 13 6dB Bandwidth ................................................................................................................................. 15 Maximum Peak Output Power .......................................................................................................... 16 Radiated Spurious Emission ............................................................................................................. 18 Conducted Spurious Emission .......................................................................................................... 22 Power Density ................................................................................................................................... 25 99% Occupied Bandwidth ................................................................................................................ 27 APPENDIX 2: Test instruments ............................................................................................................. 28 APPENDIX 3: Photographs of test setup ............................................................................................... 29 Conducted Emission ......................................................................................................................... 29 Radiated Spurious Emission ............................................................................................................. 30 Worst Case Position (Horizontal: Z-axis/ Vertical:Y-axis) .............................................................. 31 Test report No. : 10478909H-B Page : 4 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : Braveridge Co., Ltd. Address : 3-27-2 Shusenji Nishi-ku, Fukuoka-city, Fukuoka, Japan 819-0373 Telephone Number : +81-92-834-5789 Facsimile Number : +81-92-807-7718 Contact Person : Yasunari Kohashi SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Bluetooth Low Energy Module Model No. : BVMCN5111 Serial No. : Refer to Section 4, Clause 4.2 Rating : DC3.1V – 5.25V (Typ. DC3.7V) Receipt Date of Sample : August 25, 2014 Country of Mass-production : Japan Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product Description General Specification Clock frequency(ies) in the system : 32MHz Radio Specification Radio Type : Transceiver Frequency of Operation : 2402-2480MHz Modulation : GFSK Power Supply (radio part input) : DC 1.6V Antenna type : Chip Antenna Antenna Gain : 0.9dBi Test report No. : 10478909H-B Page : 5 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 3: Test specification, procedures & results 3.1 Test Specification Test Specification : FCC Part 15 Subpart C: 2014, final revised on May 1, 2014 and effective June 2, 2014 Title : FCC 47CFR Part15 Radio Frequency Device Subpart C Intentional Radiators Section 15.207 Conducted limits Section 15.247 Operation within the bands 902-928MHz, 2400-2483.5MHz, and 5725-5850MHz 3.2 Procedures and results Item Test Procedure Specification Worst margin Results Remarks Conducted Emission FCC: ANSI C63.4:2003 7. AC powerline Conducted Emission measurements FCC: Section 15.207 QP 13.1dB, 0.15105MHz, L AV 23.7dB, 0.17985MHz, L Complied - IC: RSS-Gen 7.2.4 IC: RSS-Gen 7.2.4 6dB Bandwidth FCC: "Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247(issued on June 5, 2014)" FCC: Section 15.247(a)(2) See data. Complied Conducted IC: RSS-Gen 4.6.2 IC: RSS-210 A8.2(a) Maximum Peak Output Power FCC: "Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247(issued on June 5, 2014)" FCC: Section 15.247(b)(3) Complied Cond…

Text truncated - open the document above for the full version.

Test report No. : 10478909H-B Page : 29 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Conducted Emission Photo 1 Photo 2 Test report No. : 10478909H-B Page : 30 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission Photo 1 Photo 2 Test report No. : 10478909H-B Page : 31 of 31 Issued date : September 25, 2014 FCC ID : 2ABXRBVMCN5111 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Worst Case Position (Horizontal: Z-axis/ Vertical:Y-axis) X-axis Y-axis Z-axis End of Report