2ACCBFS01MINI bluetooth barcode reader

 Data transfer When you first use the FS01 Bluetooth barcode scanners, data transfer interface is default Bluetooth interface. Pairing you can directly connect a variety of smart-phones and computers with Bluetooth function. Bluetooth output If you need to return to the Bluetooth output, you only need to press the scan button for 10 seconds to reset the Bluetooth output mode.Also can scan the bar code sets the output Bluetooth output mode. Led descriptions Meaning of representative Scan green light flashing (with buzzer ringing) Decode success Scanner light flashes continuously (scan standby) Low battery alarm The scanner red light solid In charge Scanners often turn bright red light goes out Charging is complete Scanner light flashes continuously Scanning built-in battery anomaly Scanner continuously flashing blue Enter the Bluetooth pairing mode Scanner is changed from continuous flashing blue light goes out Bluetooth link successful User Manual If you need quick access to scan the device Bluetooth pairing mode, use the scanning equipment to scan read the following illustration of "Bluetooth pairing mode" bar code. Scanning devices in the pairing process will continue flashing blue, blue light goes out after the pairing is successful. General process scanner to connect to other Bluetooth devices: connect devices having entered pairing mode → Bluetooth → search → paired Bluetooth device in the vicinity Bluetooth 3.0 Barcode Scanner → connections → scan data.  USB output If you need to use a USB cable to connect the scanner, you need to set the output mode. Please scan the following barcodes:  Serial output If you need to use a serial cable connection to the scanner, you need to set the output mode. Please scan the following barcodes: Due to the internal cloud scanner comes with mass storage, can store up to 13,000 15 bits of data messages.Cloud scanner can scan a bar code on its own and stored in the built-in mass memory. And you can use offline upload functionality, barcode data storage via Bluetooth or USB upload to your smart phone or computer. Concrete implementation steps: This note an offline scan stored procedure, for example, details the specific steps for implementation of offline scan feature: (1) Scan "offline scan status open" bar codes as shown in Figure 1to enter the offline scanning. The data you scanned will be stored in the scanning device. (2) The customer can connect to the computer through USB or Bluetooth interface or data terminal to upload the data. If customers need to save the data stored in the file, open Notepad or similar software to enter the data. If the customer wants to store data in a custom application, (such as submitted the bar code data into a application), refer the customer to the insertion point where you want to enter the data in the dialog box. Then bar code data entry and online scanning are in the same way. Customers can choose different speed to upload the data according to your application. There are three different speeds for you: fast speed, middle speed and slow-speed upload.  Fast Upload means upload data without time interval; Middle speed is to upload data the interval of 1 second; Slow upload refers to each interval of 3 seconds to upload the data. (3) The customer can also scan the "statistics storage number" bar code to view the storage section, to check the upload data entry correct or not . (4) After the upload data, related applications will store the uploaded data. Data is stored in the scanner needs clear, please scan the barcode in Figure 6 to clear the data. stored procedure. (5) After the above steps, scan "offline scan status off" bar, ending the offline scanning Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (current) 3.0 4.0 May-23-2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 4.0 Shenzhen Unique Electronic Int’l Limited D ate : June-15-2014 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Shenzhen Unique Electronic Int’l Limited _hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product Name: MINI Bluetooth barcode reader Model name: FS01 FCC ID: 2ACCBFS01 Brand: Postech Sincerely, Client’s signature: Client’s name / title : Yihua Yu/Manager Contact information / address: Shenzhen Unique Electronic Int’l Limited Rm 1608, Bld B Zhantao science and Technology, Rd Minzhi Longhua Av., Bao'an, Shenzhen 518131, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Shenzhen Unique Electronic Int’l Limited Date: June-15-2014 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2ACCBFS01 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title : Yihua Yu/Manager Contact information / address: Shenzhen Unique Electronic Int’l Limited Rm 1608, Bld B Zhantao science and Technology, Rd Minzhi Longhua Av., Bao'an, Shenzhen 518131, China

Shenzhen Unique Electronic Int’l Limited Rm 1608, Bld B Zhantao science and Technology, Rd Minzhi Longhua Av., Bao'an, Shenzhen 518131, China ----------------------------------------------------------------------------------------------------------------------------------- Declaration of Authorization We Name: Shenzhen Unique Electronic Int’l Limited Address: Rm 1608, Bld B Zhantao science and Technology, Rd Minzhi Longhua Av., Bao'an, Shenzhen 518131, China Declare that: Name Representative of agent: Wu Jian Agent Company name: MRT Technology (Suzhou) Co., Ltd Address: D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone, City: Suzhou Country China is authorized to apply for Certification of the following product(s): Product description:MINI bluetooth barcode reader FCC ID:2ACCBFS01 Model:FS01 Brand Name:Postech on our behalf. --------------------------------------------------- Signature: Yihua Yu / Manager Date: 2014-07-15

1 of 4 External Photo (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo

FS01 label and label location

1 of 3 Internal Photo (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo

MRT Technology (Suzhou) Co., Ltd Report No.: 1407RSU01902 Phone: +86-512-66308358 Report Version: V01 Fax: +86-512-66308368 Issue Date: 07-21-2014 Web: www.mrt-cert.com FCC ID: 2ACCBFS01 Page Number: 1 of 5 RF Exposure Evaluation Declaration FCC ID: 2ACCBFS01 APPLICANT: Shenzhen Unique Electronic Int’l Limited Application Type: Certification Product: MINI bluetooth barcode reader Model No.: FS01 Brand Name: Postech FCC Classification: FCC Part 15 Spread Spectrum Transmitter(DSS) Test Date: July 16 ~ 20, 2014 Reviewed By : ( Robin Wu ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 1407RSU01902 FCC ID: 2ACCBFS01 Page Number: 2 of 5 Revision History Report No. Version Description Issue Date 1407RSU01902 Rev. 01 Initial report 07-21-2014 Report No.: 1407RSU01902 FCC ID: 2ACCBFS01 Page Number: 3 of 5 1. RF Exposure Evaluation 1.1. Limits SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The equation and threshold in Note 1 must be applied to determine SAR test exclusion. MHz 5 10 15 20 25 mm 150 39 77 116 155 194 SAR Test Exclusion Threshold (mW) 300 27 55 82 110 137 450 22 45 67 89 112 835 16 33 49 66 82 900 16 32 47 63 79 1500 12 24 37 49 61 1900 11 22 33 44 54 2450 10 19 29 38 48 3600 8 16 24 32 40 5200 7 13 20 26 33 5400 6 13 19 26 32 5800 6 12 19 25 31 MHz 30 35 40 45 50 mm 150 232 271 310 349 387 SAR Test Exclusion Threshold (mW) 300 164 192 219 246 274 450 134 157 179 201 224 835 98 115 131 148 164 900 95 111 126 142 158 1500 73 86 98 110 122 1900 65 76 87 98 109 2450 57 67 77 86 96 3600 47 55 63 71 79 5200 39 46 53 59 66 5400 39 45 52 58 65 5800 37 44 50 56 62 Report No.: 1407RSU01902 FCC ID: 2ACCBFS01 Page Number: 4 of 5 Note: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] * [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison  3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°C and 78% RH. Report No.: 1407RSU01902 FCC ID: 2ACCBFS01 Page Number: 5 of 5 1.3. Test Result of RF Exposure Evaluation Product MINI bluetooth barcode reader Test Item RF Exposure Evaluation Antenna Gain: The maximum Gain measured in fully anechoic chamber is 2.0dBi for 2.4GHz in logarithm scale. Output Power into Antenna: Test Mode Frequency Band (MHz) Maximum output power to antenna (mW) SAR Test Exclusion Threshold (mW) Bluetooth 2402~2480 1.671 10 Per FCC KDB 447498 D01v05r02, the SAR exclusion threshold for distances<50mm is defined by the following equation: Based on the maximum conducted power of Bluetooth and the antenna to use separation distance, Bluetooth SAR was not required; [(1.671mW/5)* √2.402] = 0.518 < 3.0. Note: When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. The End

MRT Technology (Suzhou) Co., Ltd Report No.: 1407RSU01901 Phone: +86-512-66308358 Report Version: V01 Fax: +86-512-66308368 Issue Date: 07-23-2014 Web: www.mrt-cert.com FCC ID: 2ACCBFS01 Page Number: 1 of 72 FCC ID: 2ACCBFS01 APPLICANT: Shenzhen Unique Electronic Int’l Limited Application Type: Certification Product: MINI bluetooth barcode reader Model No.: FS01 Brand Name: Postech FCC Classification: FCC Part 15 Spread Spectrum Transmitter(DSS) FCC Rule Part(s): Part 15.247 Test Procedure(s): ANSI C63.10-2009, DA 00-705 Test Date: July 16 ~ 20, 2014 MEASUREMENT REPORT FCC PART 15.247 Bluetooth Reviewed By : ( Robin Wu ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2009 and DA 00-705. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 1407RSU01901 FCC ID: 2ACCBFS01 Page Number: 2 of 72 Revision History Report No. Version Description Issue Date 1407RSU01901 Rev. 01 Initial report 07-21-2014 1407RSU01901 Rev. 02 Update the output power limit 07-23-2014 1407RSU01901 Rev. 03 Added test environmental condition 07-23-2014 Report No.: 1407RSU01901 FCC ID: 2ACCBFS01 Page Number: 3 of 72 CONTENTS Description Page 1. INTRODUCTION ..................................................................................................................... 7 1.1. Scope ........................................................................................................................... 7 1.2. MRT Test Location ....................................................................................................... 7 2. PRODUCT INFORMATION ..................................................................................................... 8 2.1. Equipment Description .................................................................................................. 8 2.2. Frequency / Channel Opreation .................................................................................... 9 2.3. Pseudorandom Frequency Hopping Sequence ........................................................... 10 2.4. Device Capabilities ..................................................................................................... 10 2.5. Test Configuration ...................................................................................................... 10 2.6. Test Software ............................................................................................................. 10 2.7. Description of Support Units ........................................................................................ 11 2.8. EMI Suppression Device(s)/Modifications .................................................................... 11 2.9. Test environmental condition ....................................................................................... 11 2.10. Labeling Requirements ................................................................................................ 11 3. DESCRIPTION OF TEST ...................................................................................................... 12 3.1. Evaluation Procedure ................................................................................................. 12 3.2. AC Line Conducted Emissions ................................................................................... 12 3.3. Radiated Emissions .................................................................................................... 13 4. ANTENNA REQUIREMENTS ................................................................................................ 14 5. TEST EQUIPMENT CALIBRATION DATA ............................................................................ 15 6. MEASUREMENT UNCERTAINTY ......................................................................................... 16 7. TEST RESULT ...................................................................................................................... 17 7.1. Summary .................................................................................................................... 17 7.2. 20dB Bandwidth Measurement ................................................................................... 18 7.2.1. Test Limit ................................................................................................................ 18 7.2.2. Test Procedure used ............................................................................................... 18 7.2.3. Test Setting ............................................................................................................. 18 7.2.4. Test Setup ............................................................................................................... 19 7.2.5. Test Result .............................................................................................................. 20 7.3. Output Power Measurement ....................................................................................... 23 7.3.1. Test Limit ................................................................................................................ 23 7.3.2. Test Procedure Used .............................................................................................. 23 7.3.3. Test Setting ............................................................................................................. 23 Report No.: 1407RSU01901 FCC ID: 2ACCBFS01 Page Number: 4 of 72 7.3.4. Test Setup ............................................................................................................... 24 7.3.5. Test Result .........................................................…

Text truncated - open the document above for the full version.

1 of 3 Test Setup Photo Description: Front view of Conducted Emission Test Setup Description: Back view of Conducted Emission Test Setup Description: Radiated Emission Test Setup for 9kHz ~ 30MHz Description: Radiated Emission Test Setup for 30MHz ~ 1GHz Description: Radiated Emission Test Setup for 1GHz ~ 18GHz Description: Radiated Emission Test Setup for 18GHz ~ 40GHz