2AD2W-MDFPWS360WIFI MODULE

RF-WM-11AFB1 Ultra-Low-Power 2.4 GHz Wi-Fi Module Version 1.0 Shenzhen RF-star Technology Co., Ltd. Jan. 19 th , 2020 RF-WM-10AFB1 www.szrfstar.com V1.0 - Jan., 2020 Shenzhen RF-star Technology Co., Ltd. Page 1 of 25 Wi-Fi Module List Chipset Cor e RA M (KB) Tx Powe r (dBm ) Model FLASH (Byte) Antenn a Dimensio n (mm) Distanc e (m) Photo CC3235S M4 256 18 RF-WM-3235B1 S 4M Half-hol e 20.5  17.5 100 CC3235SF M4 256 18 RF-WM-3235B1 4M + 1M embedde d Half-hol e 20.5  17.5 100 CC3220 M4 256 17 RF-WM-3220B1 4M Chip / IPEX 20  31 100 CC3200 M4 256 17 RF-WM-3200B1 1M Chip 20  31 100 RF-WM-3200B1I 1M IPEX 20  31 150 Contact Me RF-WM-3200B2 16M Chip 20  31 100 RF-WM-3200B3 1M Half-hol e 20.5  17.5 100 RTL8710A F M3 512 17 RF-WM-10AFB1 1M IPEX 20  23 100 RTL8711A F M3 512 17 RF-WM-11AFB1 1M IPEX 20  23 100 Note: 1. The communication distance is the longest distance obtained by testing the module's maximum transmission power in an open and interference-free environment in sunny weather. 2. Click the picture to buy modules. RF-WM-10AFB1 www.szrfstar.com V1.0 - Jan., 2020 Shenzhen RF-star Technology Co., Ltd. Page 2 of 25 3. All modules with PCB / Chip antenna and IPEX connector are dispatched with PCB / Chip antenna only by default. If the IPEX connector is needed, pls check with me before quotation. 1 Device Overview 1.1 Description RF-WM-11AFB1 is a PCB module based on Realtek Wi-Fi SoC RTL8711AF of the CortexTM-M3 core at 83 MHz. This module has on-chip 512 KB RAM and 1 MB flash, a pin-out of peripherals of SDIO, SPI, UART, I2C, I2S, and GPIOs. It has integrated a 40 MHz crystal, an onboard PCB antenna, and an IPEX/ U.FL connector for connecting to an external antenna. It supports 2.4 GHz 802.11 b/g/n at 20 MHz channel bandwidth with 75 Mbps maximum data rate. The module comes with a pre-programmed serial interface data communication protocol and an AT commands set to minimizes users’ effort to establish the data link to their existing MCUs or processors. It supports STA, AP, and STA + AP concurrent modes, advanced security features include Wi-Fi WEP, WPA, WPA2, and WPS2 with MD5, SHA-1, SHA2-256, DES, 3DES, and AES security engines. 1.2 Key Features General - CMOS MAC, baseband PHY, and RF in a single chip for 802.11b/g/n compatible WLAN - Complete 802.11n solution for 2.4 GHz band - 72.2 Mbps receive PHY rate and 72.2 Mbps transmit PHY rate using 20 MHz bandwidth - 150 Mbps receive PHY rate and 150 Mbps transmit PHY rate using 40 MHz bandwidth - Compatible with 802.11n specification - Backward compatible with 802.11b/g devices while operating in 802.11n mode Standards supported - 802.11b/g/n compatible WLAN - 802.11e QoS Enhancement (WMM) - 802.11i (WPA, WPA2). Open, shared key, and pair-wise key authentication services - Wi-Fi WPS support - Wi-Fi direct support - Lightweight TCP/IP protocol WLAN MAC features - Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU) - Low latency immediate High-Throughput Block Acknowledgement (HT-BA) - Long NAV for media reservation with CF-End for NAV release - PHY-level spoofing to enhance legacy compatibility - Power saving mechanism WLAN PHY features - 802.11n OFDM - One Transmit and One Receive path (1T1R) - 20 MHz and 40 MHz bandwidth transmission - Short guard interval (400 ns) - DSSS with DBPSK and DQPSK, CCK modulation with a long and short preamble - OFDM with BPSK, QPSK, 16QAM, and 640QAM modulation. Convolutional coding rate: 1/2, 2/3, 3/4, and 5/6 - Maximum data rate 54 Mbps in 802.11g and 150 Mbps in 802.11n - Fast receiver Automation Gain Control (AGC) RF-WM-10AFB1 www.szrfstar.com V1.0 - Jan., 2020 Shenzhen RF-star Technology Co., Ltd. Page 3 of 25 - On-chip ADC and DAC Peripheral interfaces - SDIO slave - Maximum 2 high-speed UART interface with baud rate up to 4 MHz - 1 log UART with standard baud rate support - Maximum 3 I2C interface - I2S with 8/16/24/32/48/96/44.1/88.2 kHz sampling rate - Maximum 2 PCM with 8/16 kHz sample rate - Maximum 2 SPI supported with baud rate up to 20.8 MHz - Support 4 PWM with configurable duration and duty cycle from 0 ~ 100% - Support 4 external timer trigger event (ETE function) with a configurable period in low power mode 1.3 Applications Cloud connectivity Home automation Home appliances Access control Security systems Smart energy Internet gateway Industrial control Smart plug Smart metering Wireless audio IP network sensor nodes 1.4 Functional Block Diagram confidential RF-WM-10AFB1 www.szrfstar.com V1.0 - Jan., 2020 Shenzhen RF-star Technology Co., Ltd. Page 4 of 25 1.5 Part Number Conventions The part numbers are of the form of RF-WM-11AFB1 where the fields are defined as follows: Figure 2. Part Number Conventions of RF-WM-11AFB1 RF WM11AF Company Name RF-Star Wireless Type Wi-Fi Module Chipset Model Realtek RTL8711AF - -B1 Module Version The First Version It will not be sold toIt will not be sold to a third party until the certificate is issued a third party until the certificate is issu RF-WM-10AFB1 www.szrfstar.com V1.0 - Jan., 2020 Shenzhen RF-star Technology Co., Ltd. Page 5 of 25 It will not be sold to a third party until the certificate is issued FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Integral antenna with antenna gain 0 dBi This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, …

Text truncated - open the document above for the full version.

CompliancelistINTEGRATIONINSTRUCTIONSfor996369D03OEMtheand996369D03OEMby Sections2.2through2.10. RequirementYesN/AComment 2.2ListofapplicableFCCrules ListtheFCCrulesthatareapplicabletothe modulartransmitter.Thesearetherulesthat specificallyestablishthebandsofoperation, thepower,spuriousemissions,andoperating fundamentalfrequencies.DONOTlist compliancetounintentional-radiatorrules (Part15SubpartB)sincethatisnota conditionofamodulegrantthatisextended toahostmanufacturer.SeealsoSection2.10 belowconcerningtheneedtonotifyhost manufacturersthatfurthertestingis required.3 YESRefertoinstruction FCCstandards:FCCCFRTitle47Part15 SubpartCSection15.247 2.3Summarizethespecificoperationaluse conditions Describeuseconditionsthatareapplicableto themodulartransmitter,includingfor exampleanylimitsonantennas,etc.For example,ifpoint-to-pointantennasareused thatrequirereductioninpoweror compensationforcableloss,thenthis informationmustbeintheinstructions.Ifthe useconditionlimitationsextendto professionalusers,theninstructionsmust statethatthisinformationalsoextendstothe hostmanufacturer’sinstructionmanual.In addition,certaininformationmayalsobe needed,suchaspeakgainperfrequencyband andminimumgain,specificallyformaster devicesin5GHzDFSbands. YESRefertoinstruction Integralantennawithantennagain0dBi 2.4Limitedmoduleprocedures Ifamodulartransmitterisapprovedasa “limitedmodule,”thenthemodule manufacturerisresponsibleforapprovingthe hostenvironmentthatthelimitedmoduleis usedwith.Themanufacturerofalimited modulemustdescribe,bothinthefilingandin theinstallationinstructions,thealternative meansthatthelimitedmodulemanufacturer usestoverifythatthehostmeetsthenecessary requirementstosatisfythemodulelimiting conditions. Alimitedmodulemanufacturerhasthe flexibilitytodefineitsalternativemethodto addresstheconditionsthatlimittheinitial approval,suchas:shielding,minimum N/A Notapplicable signalingamplitude,bufferedmodulation/data inputs,orpowersupplyregulation.The alternativemethodcouldincludethatthe limitedmodulemanufacturerreviewsdetailed testdataorhostdesignspriortogivingthehost manufacturerapproval. Thislimitedmoduleprocedureisalso applicableforRFexposureevaluationwhenit isnecessarytodemonstratecomplianceina specifichost.Themodulemanufacturermust statehowcontroloftheproductintowhichthe modulartransmitterwillbeinstalledwillbe maintainedsuchthatfullcomplianceofthe productisalwaysensured.Foradditionalhosts otherthanthespecifichostoriginallygranted withalimitedmodule,aClassIIpermissive changeisrequiredonthemodulegrantto registertheadditionalhostasaspecifichost alsoapprovedwiththemodule. 2.5Traceantennadesigns Foramodulartransmitterwithtraceantenna designs,seetheguidanceinQuestion11of KDBPublication996369D02FAQ–Modules forMicro-StripAntennasandtraces.The integrationinformationshallincludeforthe TCBreviewtheintegrationinstructionsforthe followingaspects:layoutoftracedesign,parts list(BOM),antenna,connectors,andisolation requirements. 4 a)Informationthatincludespermitted variances(e.g.,traceboundarylimits, thickness,length,width,shape(s),dielectric constant,andimpedanceasapplicableforeach typeofantenna); b)Eachdesignshallbeconsidereda differenttype(e.g.,antennalengthin multiple(s)offrequency,thewavelength,and antennashape(tracesinphase)canaffect antennagainandmustbeconsidered); c)Theparametersshallbeprovidedin amannerpermittinghostmanufacturersto designtheprintedcircuit(PC)boardlayout; d)Appropriatepartsbymanufacturer andspecifications; e)Testproceduresfordesign verification;and N/A Notapplicable f)Productiontestproceduresfor ensuringcompliance. Themodulegranteeshallprovidea noticethatanydeviation(s)fromthedefined parametersoftheantennatrace,asdescribed bytheinstructions,requirethatthehost productmanufacturermustnotifythemodule granteethattheywishtochangetheantenna tracedesign.Inthiscase,aClassIIpermissive changeapplicationisrequiredtobefiledby thegrantee,orthehostmanufacturercan takeresponsibilitythroughthechangeinFCC ID(newapplication)procedurefollowedbya ClassIIpermissivechangeapplication. 2.6RFexposureconsiderations Itisessentialformodulegranteestoclearly andexplicitlystatetheRFexposureconditions thatpermitahostproductmanufacturerto usethemodule.Twotypesofinstructionsare requiredforRFexposureinformation:(1)to thehostproductmanufacturer,todefinethe applicationconditions(mobile,portable–xx cmfromaperson’sbody);and(2)additional textneededforthehostproduct manufacturertoprovidetoendusersintheir end-productmanuals.IfRFexposure statementsanduseconditionsarenot provided,thenthehostproductmanufacturer isrequiredtotakeresponsibilityofthe modulethroughachangeinFCCID(new application). YESRefertoinstruction Themodularcanbeinstalledorintegratedinmobileorfix devicesonly.Thismodularcannotbeinstalledinany portabledeviceifwithoutfurtherFCCcertify,suchasC2PC withSAR. ThismodularcomplieswithFCCRFradiationexposure limitssetforthforanuncontrolledenvironment.This transmittermustnotbeco-locatedoroperatingin conjunctionwithanyotherantennaortransmitter.This modularmustbeinstalledandoperatedwithaminimum distanceof20cmbetweentheradiatoranduserbody. 2.7Antennas Alistofantennasincludedintheapplication forcertificationmustbeprovidedinthe instructions.Formodulartransmitters approvedaslimitedmodules,allapplicable professionalinstallerinstructionsmustbe includedaspartoftheinformationtothehost productmanufacturer.Theantennalistshall alsoidentifytheantennatypes(monopole, PIFA,dipole,etc.(notethatforexamplean “omni-directionalantenna”isnotconsideredto beaspecific“antennatype”)). Forsituationswherethehostproduct manufacturerisresponsibleforanexternal connector,forexamplewithanRFpinand antennatracedesign,theintegration YES Refertoinstruction Integralantennawithantennagain0dBi instructionsshallinformtheinstallerthat uniqueantennaconnectormustbeusedonthe Part15authorizedtransmittersusedinthehost product.Themodulemanufacturersshall providealistofacceptableuniqueconnectors. 2.8Labelandcomplianceinformation Granteesareresponsibleforthecontinued complianceoftheirmodu…

Text truncated - open the document above for the full version.

SingleModularapprovalDeclarationletter We ， C&AMarketingInc.applySinglemodularapprovalfor ProductName:WIFIMODULE Model:RF-WM-11AFB1 FCCID:2AD2W-MDFPWS360 Accordingto996369D01ModuleEquipAuthGuidev01r04and15.212requirement: 1)Theradioelementsmusthavetheradiofrequencycircuitryshielded.Physical componentsandtuningcapacitor(s)maybelocatedexternaltotheshield,butmustbe onthemoduleassembly; Answer ： Yes ， shieldedforbothside. 2)Themodulemusthavebufferedmodulation/datainputstoensurethatthedevice willcomplywithPart15requirementswithanytypeofinputsignal; Answer ： Yes ； Allinputstothemodulesarebufferedthroughlogicormicroprocessor inputs. 3)Themodulartransmittermusthaveitsownpowersupplyregulation. Answer ： Yes ； Alowdropoutregulatorisusedformodularpowersupplyregulation. 4)Themodulemustcontainapermanentlyattachedantenna,orcontainaunique antennaconnector,andbemarketedandoperatedonlywithspecificantenna(s),per Sections15.203,15.204(b),15.204(c),15.212(a),2.929(b); Answer ： Yes ； DeviceisequippedwithPCBantenna. (5)Themodulemustdemonstratecomplianceinastand-aloneconfiguration; Answer ： Yes ， distancebetweenmodularandallAEsarebiggerthan10cm ， refer tosetupphoto. (6)ThemodulemustbelabeledwithitspermanentlyaffixedFCCIDlabel,orusean electronicdisplay(SeeKDBPublication784748aboutlabellingrequirements); Answer ： Yes ； Themodularhasapermanentfixedlabel,andbelowstatementwas listedintheUserManual;ThehostdevicemustbelabeledtodisplaytheFCCIDof themodule“ContainsFCCID:2AD2W-MDFPWS360” (7)Themodulemustcomplywithallspecificrulesapplicabletothetransmitter includingalltheconditionsprovidedintheintegrationinstructionsbythegrantee; Answer ： Yes ； Themodulecomplywithallspecificrulesapplicabletothe transmitterincludingalltheconditionsprovidedintheintegrationinstructionsby thegrantee,Refertotestreportandusermanual. (8)ThemodulemustcomplywithRFexposurerequirements Answer ： Yes ； TransmittermeetsMPEcalculationof47CFR1.1307.Referto MPEReportsandRefertomodularinstallationmanual Pleasecontactmeifyouhaveanyfurtherquestions.Thanksforyourattention. BestRegards, ChiefExecutiveOfficer C&AMarketingInc.

DATE:2021-4-8 FederalCommunicationsCommission Authorization& EvaluationDivision 7345 OaklandMills Road Columbia,Maryland21046 Authorityto Act as Agent On our behalf,I appointBlueAsiaof TechnicalServices(Shenzhen)Co.,Ltd. IOT Test Centreof BlueAsia，BuildingC, No. 107, ShihuanRoad,ShiyanSub-District,Baoan District,Shenzhen,GuangdongProvince,China(Nameof Agent companyname and address)to act as our agent in the preparationof this applicationfor equipmentcertification.I certifythat submitteddocuments properlydescribethe deviceor systemfor which equipmentcertificationis sought.I also certifythat each unit manufactured,importedor marketed,as definedin the FederalCommunicationsCommission’s regulations will have affixedto it a label identicalto that submittedfor approvalwith this application.Forinstanceswhere our authorizedagent signs the applicationfor certificationon our behalf,I acknowledgethat all responsibility for complyingwith the terms and conditionsfor certification,still resideswithC&A MarketingInc. 114 Tived Lane East EdisonNew JerseyUnitedStates(ApplicantNameand address) <Signature> Name：ChaimPiekarski Title ：ChiefExecutiveOfficer ApplicantCompany：C&A MarketingInc.

Model No.: RF-WM-11AFB1

SARevaluation MPECalculationMethod E(V/m)=(30*P*G) 0.5 /d PowerDensity:Pd(W/m2)=E 2 /377 E=ElectricField(V/m) P=PeakRFoutputPower(W) G=EUTAntennanumericgain(numeric) d=Separationdistancebetweenradiatorandhumanbody(m) Theformulacanbechangedto Pd=(30*P*G)/(377*d 2 ) FromthepeakEUTRFoutputpower,theminimummobileseparationdistance, d=0.2m,aswellasthegainoftheusedantenna,theRFpowerdensitycan beobtained. CalculatedResultandLimit(WORSECASEISASBELOW) Directional AntennaGain (Numeric) PeakOutput Power(mW) PowerDensity (S)(mW/cm2) LimitofPower Density(S) (mW/cm2) Test Result 1（0dBi） 27.925 （14.46dBm @2412MHz） 0.0061Compiles

Report No.: BLA-EMC-202006-A7301 Page 53 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 10 APPENDIX Appendix1 10.1 APPENDIXA: DTS BANDWIDTH Test Result TestMode Antenna Channel DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 8.120 2407.960 2416.080 >=0.5 PASS 2437 8.600 2432.960 2441.560 >=0.5 PASS 2462 9.120 2457.440 2466.560 >=0.5 PASS 11G Ant1 2412 16.440 2403.800 2420.240 >=0.5 PASS 2437 16.440 2428.760 2445.200 >=0.5 PASS 2462 16.400 2453.800 2470.200 >=0.5 PASS 11N20SISO Ant1 2412 17.440 2403.200 2420.640 >=0.5 PASS 2437 17.600 2428.200 2445.800 >=0.5 PASS 2462 17.400 2453.200 2470.600 >=0.5 PASS Report No.: BLA-EMC-202006-A7301 Page 54 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Test Graphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 11G_Ant1_2412 Report No.: BLA-EMC-202006-A7301 Page 55 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 11G_Ant1_2437 11G_Ant1_2462 11N20SISO_Ant1_2412 Report No.: BLA-EMC-202006-A7301 Page 56 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Report No.: BLA-EMC-202006-A7301 Page 57 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 10.2 APPENDIXB: OCCUPIED CHANNEL BANDWIDTH Test Result TestMode Antenna Channel OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 13.260 2405.345 2418.605 --- PASS 2437 13.334 2430.367 2443.701 --- PASS 2462 13.316 2455.306 2468.622 --- PASS 11G Ant1 2412 17.192 2403.354 2420.546 --- PASS 2437 17.306 2428.294 2445.600 --- PASS 2462 17.173 2453.380 2470.553 --- PASS 11N20SISO Ant1 2412 18.015 2402.993 2421.008 --- PASS 2437 18.026 2427.965 2445.991 --- PASS 2462 18.051 2452.936 2470.987 --- PASS Report No.: BLA-EMC-202006-A7301 Page 58 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Test Graphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 11G_Ant1_2412 Report No.: BLA-EMC-202006-A7301 Page 59 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 11G_Ant1_2437 11G_Ant1_2462 11N20SISO_Ant1_2412 Report No.: BLA-EMC-202006-A7301 Page 60 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Report No.: BLA-EMC-202006-A7301 Page 61 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 10.3 APPENDIXC: MAXIMUM CONDUCTED OUTPUT POWER Test Result TestMode Antenna Channel Result[dBm] Limit[dBm] Verdict 11B Ant1 2412 14.46 <=30 PASS 2437 12.57 <=30 PASS 2462 12.30 <=30 PASS 11G Ant1 2412 7.81 <=30 PASS 2437 7.75 <=30 PASS 2462 7.37 <=30 PASS 11N20SISO Ant1 2412 8.47 <=30 PASS 2437 7.63 <=30 PASS 2462 7.07 <=30 PASS Report No.: BLA-EMC-202006-A7301 Page 62 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Test Graphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 Report No.: BLA-EMC-202006-A7301 Page 63 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 11G_Ant1_2412 11G_Ant1_2437 11G_Ant1_2462 Report No.: BLA-EMC-202006-A7301 Page 64 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 11N20SISO_Ant1_2412 11N20SISO_Ant1_2437 11N20SISO_Ant1_2462 Report No.: BLA-EMC-202006-A7301 Page 65 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Report No.: BLA-EMC-202006-A7301 Page 66 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] 10.4 APPENDIXD: MAXIMUM POWER SPECTRAL DENSITY Test Result TestMode Antenna Channel Result[dBm/3-100kHz] Limit[dBm/3kHz] Verdict 11B Ant1 2412 -11.85 <=8 PASS 2437 -12.89 <=8 PASS 2462 -13.92 <=8 PASS 11G Ant…

Text truncated - open the document above for the full version.

Report No.: BLA-EMC-202006-A7301 Page 84 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] APPENDIX A: PHOTOGRAPHS OF TEST SETUP Antenna Requirement Radiated Spurious Emissions Report No.: BLA-EMC-202006-A7301 Page 85 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Report No.: BLA-EMC-202006-A7301 Page 86 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Conducted Emissions Report No.: BLA-EMC-202006-A7301 Page 87 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] Report No.: BLA-EMC-202006-A7301 Page 88 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] APPENDIX B: PHOTOGRAPHS OF EUT Report No.: BLA-EMC-202006-A7301 Page 89 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] ----END OF REPORT---- The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of BlueAsia, this report can’t be reproduced except in full.

Page 1 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. Add: Building C, No. 107, Shihuan Road, Shiyan Sub-District, Baoan District, Shenzhen, Guangdong Province, China Tel: +86-755-23059481 Email: [email protected] www.cblueasia.com TEST REPORT Product Name : WIFI MODULE Brand Mark : Logia Model No. : RF-WM-11AFB1 FCC ID : 2AD2W-MDFPWS360 Report Number : BLA-EMC-202006-A7301 Date of Sample Receipt : 2020/6/24 Date of Test : 2020/6/24 to 2020/7/4 Date of Issue : 2021/4/8 Test Standard : 47 CFR Part 15, Subpart C 15.247 Test Result : Pass Prepared for: C&A Marketing Inc. 114 Tived Lane East Edison , New Jersey, United States Prepared by: BlueAsia of Technical Services(Shenzhen) Co.,Ltd. Building C, No. 107, Shihuan Road, Shiyan Sub-District, Baoan District, Shenzhen, Guangdong Province, China TEL: +86-755-23059481 Compiled by: Review by: Approved by: Date: 2021/4/8 Report No.: BLA-EMC-202006-A7301 Page 2 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] REPORT REVISE RECORD Version No. Date Description 00 2020/7/6 Original 01 2021/4/8 Change of Applicant Report No.: BLA-EMC-202006-A7301 Page 3 of89 BlueAsia of Technical Services(Shenzhen) Co., Ltd. IOT Test Centre of BlueAsia,No. 448 Bulong Road, Bantian Street, Longgang District, Shenzhen, China Telephone: TEL: +86-755-28682673 FAX: +86-755-28682673 Email:[email protected] TABLE OF CONTENTS 1 TEST SUMMARY ........................................................................................................................................6 2 GENERAL INFORMATION .........................................................................................................................7 3 GENERAL DESCRIPTION OF E.U.T. .........................................................................................................7 4 TEST ENVIRONMENT ................................................................................................................................8 5 TEST MODE ................................................................................................................................................8 6 MEASUREMENT UNCERTAINTY ..............................................................................................................8 7 DESCRIPTION OF SUPPORT UNIT...........................................................................................................9 8 LABORATORY LOCATION .........................................................................................................................9 9 TEST INSTRUMENTS LIST ..................................................................................................................... 10 CONDUCTED SPURIOUS EMISSIONS ........................................................................................................... 14 LIMITS ............................................................................................................................................................................. 14 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................................... 14 TEST DATA ........................................................................................................................................................................ 15 CONDUCTED BAND EDGES MEASUREMENT ............................................................................................. 16 LIMITS ............................................................................................................................................................................. 16 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................................... 16 TEST DATA ........................................................................................................................................................................ 17 POWER SPECTRUM DENSITY ....................................................................................................................... 18 LIMITS ............................................................................................................................................................................. 18 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................................... 18 TEST DATA ........................................................................................................................................................................ 18 CONDUCTED PEAK OUTPUT POWER .......................................................................................................... 19 LIMITS ............................................................................................................................................................................. 19 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................................... 19 TEST DATA ........................................................................................................................................................................ 20 MINIMUM 6DB BANDWIDTH ........................................................................................................................... 21 LIMITS ............................................................................................................................................................................. 21 BLOCK DIAGRAM OF TEST SETUP .................................................................................…

Text truncated - open the document above for the full version.