2AD33S113CShockwave 100 Wireless Party Speaker

IMT7001 Quick Start Guide IMT7001 IMT7001 Adapter AUX. Audio cable Wired Mic.x1 AUX: For line level or headphone output from audio sources USB OUT: For charging your mobile devices DC IN: Plug for power adapter MIC2: For 2nd wired microphone MIC1: For 1st wired microphone Descriptions about the various ports on the speaker INPUT/OUTPUT PORTS Play/pause Previous song or FM station Next song or FM stationBass-: decrease bass Bass+:increase bass Press and hold button 3 seconds to power on or power off speaker Select mode (FM or AUX) Select Bluetooth mode Light modes VOLUME-: decrease volume VOLUME+: increase volume Brief introduction to buttons on top panel Press MIC1 and MIC2 volume buttons to increase or decrease the volume of both microphones MIC Volume ControlPower Button (also used for stereo pairing see later section) (BT mode only) AL Shockwave 100 Bluetooth Connection Stereo pairing (two speakers) : 1. Have one speaker turned on, paired and playing music. It will serve as the HOST (the Primary speaker). The display will be showing ‘Bt’ (Pair by pressing the BT/PAIR button, BT ashes on the display then goes solid when paired). 2. Power on an additional compatible speaker. It will serve as a Secondary speaker. 3. Press and hold the BT/PAIR button on the Primary speaker for approximately two seconds or until the display changes from solid ‘Bt’ to ashing ‘HOSt’. 4. Quickly tap the BT/PAIR button on the Secondary speaker. The display should change from ashing ‘Bt’ (normal pairing) to ashing ‘St PAIr’ (stereo pairing). 5.The speakers will connect and then both displays will show ‘Bt’. The speakers will now play the same music from the same audio source, one will play Left and one will play Right. Go to the Bluetooth settings menu on your phone. Make sure that Bluetooth is turned on. Connect to the device listed as “AL Shockwave 100” Primary Speaker Secondary Speaker LIGHTING CONTROL Briey press the LIGHTS button for lighting control: (Noted: Cone’s light will be displayed while unit is playing music) LED 1: Side lights scrolling multi-color, cones’ color change with the beat; press and hold to change as single color scrolls one by one; Length of Audio cable(stereo-to-stereo):90cm Length of adaptor:110cm Length of wired micphone’s cable:285cm L267xW238xH504(mm) 43W (RMS) 150W (Peak) Total 5.25” x2 + 2” x1 DC input:15V 1.5A LED 2: Sides & cones follow music and change color automatically every 3 seconds; LED 3: Side lighting one color, cones follow music to ash the same color, press and hold for 3 seconds to change to the other color; LED 4: Sides o, just cones ash into one color, press and hold for 3 seconds to change to the other color; LED 5: Sides do a bar graph from the middle in one color and cones ash the same color, press and hold for 3 seconds to change to the other color; LED 6: Sides and cones slowly change colors automatically every 3 seconds, press and hold to turn cone lights o; LED 7: Sides ash one color, cones no light, press and hold for 3 seconds to change to the other color; LED 8: Sides do a multi-color bar graph from the middle, cones o; LED 9: Sides fade between colors, cones o; OFF : Lighting o. Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identier Trade Name: Altec Lansing Model No.: IMT7001 Responsible Party – U.S. Contact Information US Company Name: SAKAR INTERNATIONAL INC. Address: Edison, NJ 08817 Telephone number or internet contact information: 855-292-4087 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. RF Exposure Compliance IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions – All the safety and operating instructions should be read before this product is operated. 2.Keep these instructions – The safety and operating instructions should be retained for future reference. 3.Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to. 4.Follow all instructions – All operating and use instructions should be followed. 5.Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like. 6.Clean only with dry cloth. 7.Do not block any ventilation openings. Install in accordance with the manufacture’s instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10.Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. 11.Only use attachments/accessories specified by the manufacturer. 12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.Unplug the apparatus during lightning storms or when unused for long periods of time. 14.Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15.CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not…

Text truncated - open the document above for the full version.

F LY I A L L SIEC rft ON/C rSHE/VZHE CO. tID TO: FederalCommunicationCommission Equipment Authorization Branch 7435 Oaktand Milts Road Cotumbia, MtD 21046 Regarding: FeG [t]iii* Hg$ ::33e To whom it may concern: We, the undersigned, hereby authorize iiliXi."".",g:*X?,i:i,:l1n-"lgUtg:i.lid;;$F;d;i;HJJ"?:-:,::ffi="XT:[:lJ:ffi::out by the agent on our behalishi, n5r" tr","irr;;ii;i;;;;Y";i';;;"J; Title: Sales Manager LECTRONTC (SHENZHEN) CO. LTD E-mail: josie@ftybail. com. cn Dale 2O20l7tB we' the undersigned, lerelY certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to section 5aot or the Anti-Drurj nori" n"i of 1988, 21 u.s.c. 853(a). where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms'and conditionslolggllli"^r1i*, "" .p""iri"d by sGgNorth America, lnc., stiil resides with FLyBALL ELECTRONTC (SHENZHEN) CO. liD '"- This authorization is varid until further written notice from the appricant. G*KI"c- !- i z

FLYSALL ErECrROi#C TSHENZHEiIJ CA. LTD To: Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: FLYBALL ELECTRONTC (SHENZHEN) CO. LTD 5-6 Building, Zhiji lndustrial Park, Shenzhen, China Regarding: Confidentiality Request regarding application for rCC U:: 2AD33S1t3C LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 ofthe commission's rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. lf the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FGC KDB 726920 D01 Confi dentiality Request Procedures. External Photos lnternal Photos Test Setup Photos User manual(s) Sincerely, Title: Sales Manager (*ltl).fpfi 'p\ Telephone: 86-1 E-mail: [email protected] (SHENZHEN)CO. LTD

SGS North America lnc. 620 Old Peachtree Road SUITE 1OO Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name FLYBALL ELECTRONIC (S}IENZ}IEN) CO. LTD Address 5-6 Building, Zhiji Industrial Park, Shenzhen, China Grantee Code 2AD33 FCC ID 2AD33S1I3C Authorized Contact Name Josie Zhang Contact Email [email protected] Contact Phone 86-135s4753826 l, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47cFR2.g1 1(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in ' this application, the Applicant is responsible for: . (1) labeling the equipment with the exact FCC lD as specified in this application, ' iZi compliince statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules' c) if the Applicant is not the actual manufacturer of the equipment, appropriale arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. d) in accordance wtth 47 cFR 2.909 and KD83g4321, the Applicant has re_ad, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with tso17065, FCC KDB641 163, FCC KDB61OO77, KDB3}4321 anil RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements' (1) the Applicant understands, accepts and agrees that a sample may be requested for surveill4nce testing. izi ttr" nb'pticant sfiail make provisibns to alr,iays have a production iample available upon request by SGS, FCC and/or ISED' (3) the Applicant sfrilf upon iequest by Scs, it tne Applicant's expense, provide a production sample of the requested product to SGS, FCC and/or lSfO as instructbd. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Appticant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Aur.,i Ait 6t 19g8, ii u.s.c. 5862 becuuse of a conviction for possession or distribution of a controlled substance. see 47CFR 1.2002(b) forthe definition ofa "party''forthese purposes' S) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, lnc.(TCB) terms and conditions. Link to CFRs: httrs://www.fcc.oov/wirelesslbureau-divisions/technoloqies-svstems-and-innovation-division/rules-requlations{itle-47 Link to KDBs: Link to RSP-100: Applicant Declaration Rev:0.0 WOIE: Ifi,s cannat be signed by an Agen4 it shall signed by an person listed in the

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 5 External Photos for SZEM2006005113CR FCC ID: 2AD33S113C SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 5 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 5

S113PC 20MM DATE CODE: 07/2020 ITEM NO.: IMT7001 PRODUCT DESCRIPTION: Shockwave 100 Wireless Party Speaker DC INPUT: 15V 1.5A MID#3580720 TECH SUPPORT #:1.855.292.4087 MADE IN CHINA FCC ID: 2AD33S113C THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE , AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Composite wood containing products complies with TSCA Title VI Manufacturer: SAKAR INTERNATIONAL INC. 800562 US

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 Internal Photos for SZEM2006005113CR FCC ID: 2AD33S113C SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 Antenna 1 & module 1 Antenna 2 & module 2 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 7

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511303 Page: 1 of 7 Keny Xu EMC Laboratory Manager 1 Cover page SAR Evaluation Report Application No.: SZEM2006005113CR Applicant: FLYBALL ELECTRONIC (SHENZHEN) CO. LTD Address of Applicant: 5-6 Building, Zhiji Industrial Park, Shenzhen, China Manufacturer: SAKAR INTERNATIONAL INC Address of Manufacturer: Edison, NJ08817 Factory: FLYBALL ELECTRONIC (SHENZHEN) CO. LTD Address of Factory: 5-6 Building, Zhiji Industrial Park, Shenzhen, China Equipment Under Test (EUT): EUT Name: Shockwave 100 Wireless Party Speaker Model No.: IMT7001 Trade mark: Altec Lansing FCC ID: 2AD33S113C Standards: 47 CFR Part 1.1307 47 CFR PART 2.1091 Date of Receipt: 2020-06-15 Date of Test: 2020-06-24 to 2020-07-10 Date of Issue: 2020-07-14 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511303 Page: 2 of 7 2 Version Revision Record Version Chapter Date Modifier Remark 01 2020-07-14 Original Authorized for issue by: Powell Bao /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511303 Page: 3 of 7 3 Contents Page 1 COVER PAGE .............................................................................................................................................. 1 2 VERSION ...................................................................................................................................................... 2 3 CONTENTS .................................................................................................................................................. 3 4 GENERAL INFORMATION .......................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF EUT ............................................................................................................. 4 4.2 TEST LOCATION ...................................................................................................................................... 5 4.3 TEST FACILITY ........................................................................................................................................ 5 4.4 DEVIATION FROM STANDARDS ................................................................................................................. 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 5 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 5 5 RF EXPOSURE EVALUATION .................................................................................................................... 6 5.1 RF EXPOSURE COMPLIANCE REQUIREMENT ............................................................................................ 6 5.1.1 Limits ................................................................................................................................................ 6 5.1.2 Test Procedure ................................................................................................................................ 6 5.1.3 EUT RF Exposure Evaluation .......................................................................................................... 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511303 Page: 4 of 7 4 General Information 4.1 General Description of EUT Power supply: Powered by DC11.1V rechargeable battery and can be charged by adapter with Model:AD0301-15015000UB Input: AC100-240V,50/60Hz, 0.8A max Output: DC15V, 1.5A; 22.5W Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V4.2 Classic Spectrum Spread Technology: Frequency Hopping Spread Spectrum(FHSS) Modulation Type: GFSK, π/4DQPSK, 8DPSK Number of Channels: 79 Channel Spacing: 1MHz Antenna Type: PCB Antenna Antenna Gain: 0.5dBi Remark: There are two Bluetooth modules in the product and there are all the same. Module 1 act as main chip and can be paired with mobile phone, Module 2 act as the secondary TWS module and can be paired with another module 1 of Shockwave 100 Wireless Party Speaker. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511303 Page: 5 of 7 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0006. I…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511302 Page: 1 of 135 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM2006005113CR Applicant: FLYBALL ELECTRONIC (SHENZHEN) CO. LTD Address of Applicant: 5-6 Building, Zhiji Industrial Park, Shenzhen, China Manufacturer: SAKAR INTERNATIONAL INC Address of Manufacturer: Edison, NJ08817 Factory: FLYBALL ELECTRONIC (SHENZHEN) CO. LTD Address of Factory: 5-6 Building, Zhiji Industrial Park, Shenzhen, China Equipment Under Test (EUT): EUT Name: Shockwave 100 Wireless Party Speaker Model No.: IMT7001 Trade Mark: Altec Lansing FCC ID: 2AD33S113C Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2020-06-15 Date of Test: 2020-06-24 to 2020-07-10 Date of Issue: 2020-07-14 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511302 Page: 2 of 135 Revision Record Version Chapter Date Modifier Remark 01 2020-07-14 Original Authorized for issue by: Powell Bao /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511302 Page: 3 of 135 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.247(a)(1),(g),(h) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.5 47 CFR Part 15, Subpart C 15.247(b)(1) Pass 20dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.7 47 CFR Part 15, Subpart C 15.247(a)(1) Pass Carrier Frequencies Separation 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.2 47 CFR Part 15, Subpart C 15.247a(1) Pass Hopping Channel Number 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.3 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Dwell Time 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.6 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.8 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200600511302 Page: 4 of 135 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 6 4.4 TEST LOCATION .................................................................................................................................... 7 4.5 TEST FACILITY ...................................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 7 5 EQUIPMENT LIST ...................................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 13 6.1 ANTENNA REQUIREMENT .................................................................................................................... 13 6.1.1 Test Requirement: ....................................................................................................................... 13 6.1.2 Conclusion ................................................................................................................................... 13 6.2 OTHER REQUIREMENTS FREQUENCY HOPPING SPREAD SPECTRUM SYSTEM HOPPING SEQUENCE ........ 14 6.2.1 Test Requirement: ....................................................................................................................... 14 6.2.2 Conclusion ................................................................................................................................... 14 7 RADIO SPECTRUM MATTER TEST RESULTS ....…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZEM2006005113CR FCC ID: 2AD33S113C SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs 1.1 Conducted Emissions at AC Power Line (150kHz-30MHz) Test Setup 1.2 Radiated Emissions which fall in the restricted bands Test Setup SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 1.3 Radiated Spurious Emissions Test setup