2AD33S34BOutdoor Bluetooth Speaker

Reorient or relocate the receiving antenna. cambie la orientación o ubicación de la antena receptora.

Important Safety Instructions Caution: To reduce the risk of electric shock, do not dismantle this product. There are no user-serviceable parts inside. Refer se rvicing to qualified personnel only. Explanation of Symbols: The lightning flash within an equilateral triangle is intended to alert you to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute an electric shock to a person or persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. To achieve the utmost in enjoyment and perform ance, and in order to become familiar with its features, please read this user guide carefully be fore attempting to operate this product. This will assure you years of trouble free performance and listening pleasure. Important Notes This user guide should be retained for future reference. Do not install the product in the following areas:  Places exposed to direct sunlight or close to radiators.  On top of other equipment that radiate too much heat.  Blocking ventilation or in a dusty area.  Areas where there is constant vibration.  Near candles or other open flames. Operate the product only as instructed in this guide. For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any servicing to qualified personnel. Do not attempt to remove any screws, or open the casing of the unit; there are no user, serviceable parts inside. Refer all servicing to qualified service personnel. Conformity General Safety Instruction: All the safety and operating instructions must be read before the product is operated. All warnings on the product and in the user guide should be adhered to. All operating and users’ instructions should be followed. Install in accordance with the manufacturer's instructions. The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products, including amplifiers that produce heat. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Only use attachments recommended by the pr oduct manufacturer, as they may cause hazards. Do not attempt to service this product your self. Opening or removing covers may expose you to dangerous voltage or other hazards. Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speaker may be dam aged when a peak level section is suddenly played. WARNING: This speaker is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concer ning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the speaker. This is not a toy. • The unit is not intended to be operated by means of an external timer or separate remote control system. • Do not cover the ventilation opening with items such as newspaper, table-cloths, curtains etc. • Do not place this unit clos e to a strong magnetic field. • Do not attempt to clean the unit with c hemical solvents as this might damage the finish. Wipe with a clean, dry or slightly damp cloth. • Do not place speaker too close to ear s, it may cause damage to ear drums, especially in young children. Use this appliance only for its intended use as described in this manual. Bauhn is not liable for any damage caused to iPod/MP3 player or any other device. Do not place or store appliance where it can fall or be pulled into a bath or sink. Do not place in or drop into water or any other liquids. Battery Information: Battery lifetime will last longer if you follow guidelines below for charging and storing:  The speaker has a built-in rechargeable battery. Make sure the battery has been fully charged before first use.  The first battery charge may take up to 10 hours. The battery will have a better performance after 3 full charges and discharges. It is better to charge the unit only after it is completely discharged.  Recharge and store the unit within the temperature range of 40°F~95°F (05°C~35°C)  Do not charge the battery for a period longer than 24 hours. Excessive charging may shorten the battery's life.  Turn off the speaker if you are not going to use it for a long period of time. The display will show ”LO-BATT” when the speaker’s battery powe r is too low. The speaker will switch off automatically due to insufficient power. Please follow the user guide for charging. The speaker cannot work if there is no power in the battery. You may charge it for a while and then try to switch on again to resume playback. Important note: This device is equipped with an energy sa ving mode: if no signal is given during 15 minutes the device will switch automatically into standby mode in order to save energy (ERP 2 standard). Please note that low volume setting in the audio source may be recognized as “no audio signal”: this will affect the capability of signal detection from the device and can also originate an automatic switch into standby mode. If this happens, please reactivate the audio signal transmission or increase the volume setting on the audio source player (MP3 player, etc.), in order to resume playback. LOCATION OF CONTROLS 1 Play & Pause/Pairing 2 Previous 3 Next 4 Volume down (-) 5 Volume up (+) 6 LED Bluetooth (Blue) 7 LED charge (yellow) 8 LED display 9 AUX in socket 10 Power ON/OFF switch 11 Micro USB charge port Using the Speaker Turn on the unit Slide the rear panel Power knob (10) to ON position. The LED display (8) will flash on as below. BLUETOOTH OPERATION 1. The LED display (8) will show “Bt” as below and th…

Text truncated - open the document above for the full version.

FLYBALL ELECTRONIC (SHENZHEN) CO.,LTD Authority to Act as Agent Date: __Jan.26.2015_ To Whom It May Concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Vicky Yuan in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ___12 months_____ By: Teddy hung (Signature) (Print name) Title: G.m On behalf of: FLYBALL ELECTRONIC (SHENZHEN) CO.,LTD (Company Name) Telephone: (86)755 61669696-5215

FLYBALL ELECTRONIC (SHENZHEN) CO.,LTD Request for Confidentiality Date: 2015/01/30 Subject: Confidentiality Request for: FCC ID: 2AD33 S34B Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ FLYBALL ELECTRONIC(SHENZHEN) CO.LTD has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, Teddy Hung By: _______________ (Signature/Title 3 ) (Print name) FLYBALL ELECTRONIC (SHENZHEN) CO.,LTD

1 PHOTOGR APHS - EUT CONSTRUCTION AL DETAILS Test Model No.: 45305

2AD33S34B

1 PHOTOGR APHS - EUT CONSTRUCTION AL DETAILS Test Model No.: 45305

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150100005502 Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No: SZEM1501000055CR Applicant: Flyball Electronic (Shenzhen) Co.,LTD. Manufacturer/ Factory: Flyball Electronic (Shenzhen) Co.,LTD. Product Name: Outdoor Bluetooth Speaker Model No.(EUT): 45305 Trade Mark: BAUHN FCC ID: 2AD33S34B Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2015-01-07 Date of Test: 2015-01-19 to 2015-01-26 Date of Issue: 2015-02-02 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150100005502 Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-02-02 Original Authorized for issue by: Tested By 2014-10-26 (Eric Fu) /Project Engineer Date Prepared By 2015-02-02 (Linlin Lv) /Clerk Date Checked By 2015-02-03 (Kevin Feng) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150100005502 Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE .............................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150100005501 Page: 1 of 95 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1501000055CR Applicant: Flyball Electronic (Shenzhen) Co.,LTD. Manufacturer/ Factory: Flyball Electronic (Shenzhen) Co.,LTD. Product Name: Outdoor Bluetooth Speaker Model No.(EUT): 45305 Trade Mark: BAUHN FCC ID: 2AD33S34B Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-01-07 Date of Test: 2015-01-19 to 2015-01-26 Date of Issue: 2015-02-02 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150100005501 Page: 2 of 95 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-02-02 Original Authorized for issue by: Tested By 2015-01-26 (Eric Fu) /Project Engineer Date Prepared By 2015-02-02 (Linlin Lv) /Clerk Date Checked By 2015-02-03 (Kevin Feng) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150100005501 Page: 3 of 95 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 (2009) PASS AC Power Line Conduc…

Text truncated - open the document above for the full version.

1 PHOTOGR APHS - EUT TEST SETUP Test Model No.: 45305 1.1 CONDUCT ED EMISSIO N 1.2 RADIAT ED EMISSIO N