2AD5K-PTC100Wireless Charging Pad

P roduct Name : Wireless Charging PAD Model : PTC-100 Manufacturer : Partron Co., Ltd. 22 Samsun g 1-ro 2-gil, Hwaseong-si, Gyeonggi-do, Korea 445-170 TEL 82-31-201-7791 | FAX 82-31-201-7800 | Homepage www.partron.co.kr / www.croise.co.kr PTC-100 Compact Wireless Charger Manual Precautions for safety The contents inside the product warranty is described below to ensure user's safety and prevent property damage. Please read the manual carefully to use the product appropriately. Partron is not responsible for any injury or damage occurred by not following safety precautions. Please do not use damaged power cord, plug, and loose socket. Please do not contact power plug with wet hands, and do not unplug by pulling the cord part. Please do not bend or damage power cord. Please do not place or use the product nearby coin, key, cell phone, accessories, metal. The product could cause the heat. If the product overheated, please put down the cell phone from the charger for separation. Then, please pause using the product. Please be cautious in use since the contact with the heated product on the skin could cause the red spots, pigmentation, and low-temperature burn. Please do not place the product nearby stove, microwave, heating utensil, or high heat container. This may cause a re. - Do not drop the product or impact on the product. - Do not store or leave the product on a sloping area. - Product can be damaged, and internal parts can be broken. - Please be cautious and guide children, baby or pet not to suck or bite the product. - Please do not use the product other than its original purpose. - Please leave the product on dry area where is not wet or damp. Humidity or liquid components can damage on part and circuit of product. If product gets wet, remove the moisture with a dry towel and take it to service center. - Do not alter, disassemble, or repair. Make sure to use a repair service center qualied by Parton. Free repair is not available if there is any alteration, disassemble, or repair. This device is built for home use (B level), and completed EMC registration. It is usable in every area, and primarily intended for use in homes and offices. Using the Product 1. Please connect power after connecting AC ADAPTER(sold separately) to compact wireless charger. ( ! ) Be sure to use original 5V/2.0A AC ADAPTER. Otherwise, it will not be recharged properly, or it can cause defects or damage. - Especially, AC ADAPTER for compact wireless charger is 5V/2.0A, so use of nonstandard ADAPTER can lead to slow recharge. - If this 5V/2.0A original AC ADAPTER is used for existing mobile charger or other low ratings, it could cause re, explosion, or defects/damage. ( !! ) Current status of product could be checked by the color of status indicator on compact wireless charger. If the status indicator does not function properly or incorrectly recognized, disconnect the charger and reconnect them. Color of Status indicator Wireless Charger Status Off Standby and Charging completed Green Flashed Charging in progress Red Flashed Fast When foreign object (knife, key, metal substance and etc) is recognized between cell phone and compact wireless charger, FOD function operates Red Flashed Slow Pressure lower than rated power (5V/2A of Genuine Adapter is recommended.) Red Fixed Wireless charger operates inappropriately * Color of Status indicator after full charge will not be changed per phones 2. Firstly, please place cell phone on compact wireless charger after attaching either wireless charge cover or patch. ( ! ) Be sure to place rear side of your cell phone completely on wireless charger. 3. Please separate AC ADAPTER (sold separately) from compact wireless charger when charging is completed. ( ! ) To check charging status, please check charger icon on your cell phone display. - Wireless charger might not function properly if foreign substances exist between cell phone and compact wireless charger. - DMB is not available while wireless charging. - If compact wireless charger is used where signal is weak, reception rate of cell phone could be weak. - This product is compatible with the Wireless Power Consortium(WPC) certied product. 4. Please do not place wireless charger cover on compact wireless charger alone. This product has been designed to flow current when charger cover and compact wireless charger are correctly in contact. If a charger cover is left alone on compact charger, it might lead to excessive heat, which could cause re or defects/damage on the device. (X) (O) Spec and Features ITEM Specification Size 72 x 72 x 15 (W x L x T) mm 3 Recharging Method Magnetic Induction Method (WPC Standard) Transmission Power DC 5W (Maximum 5V, 1A) Using Frequency Range 115 ~ 205kHz Input Power DC 5V, 2.0A Operating Temperature -20 °C ~ +60 °C FCC Warning information FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. RF Exposure Statement (2.1091) This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

External photos of EUT Front view of EUT Rear view of EUT Side view of EUT

FCC Label 1. FCC Label Drawing Wireless Charging Pad Model Name : PTC-100 Input Power : DC 5.0V 2.0A Manufacturer: YantaiPartron Co.,Ltd. A/S : +82-31-201-7707 FCC ID : 2AD5K-P TC100 CMIIT ID : 2015DJ3436 Made in China 2. FCC Label Location Back side

Internal photos of EUT Internal view of EUT Top view of main board Bottom view of main board Loop Coil Antenna

Report Number : F690501/RF-RTL009018 Page: 2 of 9 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) INDEX TABLE OF CONTENTS Page 1. General Information ----------------------------------------------------------------------- 3 2. Test Result ----------------------------------------------------------------------------------- 5 Report Number : F690501/RF-RTL009018 Page: 3 of 9 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1. General information 1.1. Testing laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) - Wireless Div. 2FL, 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-837 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx . Phone No. : +82 31 688 0901 Fax No. : +82 31 688 0921 1.2. Details of applicant Applicant : PARTRON Co., Ltd. Address : 22, Samsung 1-ro 2-gil, Hwaseong-Si, Gyeonggi-Do, Korea Contact Person : Jeong, Hae-Young Phone No. : + 82 31 201 7800 1.3. Description of EUT Kind of Product Wireless Charging Pad Model Name PTC-100 Power Supply DC 5 V (AC 100 V ~ 240 V Travel Adaptor) Frequency Range 115 ㎑ ~ 205 ㎑ Operating Conditions -20 °C ~ 60 °C Antenna Type Inductive loop coil antenna H/W Version Ver2.3 S/W Version Ver P.1.0.6 Report Number : F690501/RF-RTL009018 Page: 4 of 9 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.4. Test Equipment List Equipment Manufacturer Model S/N Cal Date Cal Interval Cal Due. E-Field Probe ETS-LINDGREN HI-6005 00047870 Mar. 11, 2015 Annual Mar. 11, 2016 Magnetic Field Sensor HIOKI 0850-B1 3471 Jul. 16, 2015 Annual Jul. 16, 2016 Magnetic Field Hitester HIOKI FT3470-50 140430999 Jul. 16, 2015 Annual Jul. 16, 2016 Anechoic Chamber SY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/A N.C.R. N/A N.C.R. 1.5. Test report revision Revision Report number Date of Issue Description 0 F690501/RF-RTL009018 2015.08.20 Initial 1.6. Worst case of test configurations In order to check all kinds of possible configurations, EUT was evaluated with appropriate client and under each charging condition as below table. EUT configuration Description Charging Mode with client device (Galaxy Note 4 : SM-N910U FCC ID : A3LSMN910U) Less than 1 % of battery Less than 50 % of battery 100 % full charging of battery Report Number : F690501/RF-RTL009018 Page: 5 of 9 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 2. Test Result 2.1. Test Setup 2.1.1. Distance 10 ㎝ between the edge of EUT and center of Probe 2.2. Measurement procedure a) The RF exposure test was performed on 360 degree turn table in anechoic chamber. b) The measurement probe was placed at test distance (10 ㎝) which is between the edge of the charger and the geometric center of probe. c) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E, F) were completed. d) The EUT were measured according to the dictates of KDB 680106 D01v02. Report Number : F690501/RF-RTL009018 Page: 6 of 9 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 2.3. Equipment Approval Considerations. The EUT does comply with item 5.2 of KDB 680106 D01v02. a) Power transfer frequency is less that 1 ㎒. - The device operates in the frequency range from 115 ㎑ to 205 ㎑. b) Output power from each primary coil is less than 5 watts. - DC 5 V (Travel adapter output)  Output power from each primary coil : 5 W (Max.) c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. - The transfer system includes only single primary and secondary coils. Refer to a photo in the Internal photos. d) Client device is inserted in or placed directly in contact with the transmitter. - Client device is placed directly in contact with the transmitter. e) The maximum coupling surface area of the transmit (charging) device: - The EUT coupling surface area : 7.2 cm(W) x 7.2 cm(D) = 51.84 cm 2 , 51.84 cm 2 < 60 cm 2 . f) Aggregate leakage fields at 10 cm surrounding the device from all simultaneous transmitting coils …

Text truncated - open the document above for the full version.

Report Number : F690501/RF-RTL009017 Page: 2 of 21 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) INDEX TABLE OF CONTENTS Page 1. General Information -------------------------------------------------------------------------- 3 2. Field Strength of Fundamental and Spurious Emission ----------------------------- 6 3. 20 ㏈ Bandwidth ----------------------------------------------------------------------------- 15 4. Transmitter AC Power Line Conducted Emission ------------------------------------ 17 Report Number : F690501/RF-RTL009017 Page: 3 of 21 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1. General Information 1.1. Testing laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) - Wireless Div. 2FL, 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-837 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx . Phone No. : +82 31 688 0901 Fax No. : +82 31 688 0921 1.2. Details of applicant Applicant : PARTRON Co., Ltd. Address : 22, Samsung 1-ro 2-gil, Hwaseong-Si, Gyeonggi-Do, Korea Contact Person : Jeong, Hae-Young Phone No. : + 82 31 201 7800 1.3. Description of EUT Kind of Product Wireless Charging Pad Model Name PTC-100 Power Supply DC 5 V (AC 100 V ~ 240 V Travel Adaptor) Frequency Range 115 ㎑ ~ 205 ㎑ Operating Conditions -20 °C ~ 60 °C Antenna Type Inductive loop coil antenna H/W Version Ver2.3 S/W Version Ver P.1.0.6 Report Number : F690501/RF-RTL009017 Page: 4 of 21 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.4. Test Equipment List Equipment Manufacturer Model S/N Cal Date Cal Interval Cal Due. Spectrum Analyzer R&S FSV30 100768 Mar. 24, 2015 Annual Mar. 24, 2016 Signal Generator R&S SMBV100A 255834 Jun. 22, 2015 Annual Jun. 22, 2016 Signal Generator R&S E8257D MY51501169Jul. 13, 2015 Annual Jul. 13, 2016 DC Power Supply Agilent U8002A MY48490027Dec. 22, 2014 Annual Dec. 22, 2015 Preamplifier H.P. 8447F 2944A03909Aug. 27, 2014 Annual Aug. 27, 2015 Test Receiver R&S ESU26 100109 Mar. 03, 2015 Annual Mar. 03, 2016 Test Receiver R&S ESCI 7 100911 Dec. 24, 2014 Annual Dec. 24, 2015 Loop Antenna R&S HFH2-Z2 100118 Jun. 04, 2015 Biennial Jun. 04, 2017 Bilog Antenna Schwarzbeck Mess-Elektronik VULB9163 396 Jun. 18, 2015 Biennial Jun. 18, 2017 Two-Line V-Network R&S ENV216 100190 Dec. 25, 2014 Annual Dec. 25, 2015 Antenna Master INN-CO MM4000 N/A N.C.R. N/A N.C.R. Turn Table INN-CO DS 1200 S N/A N.C.R. N/A N.C.R. Anechoic Chamber SY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/A N.C.R. N/A N.C.R. Shield Room SY Corporation L × W × H (6.5 m × 3.5 m × 3.5 m) N/A N.C.R. N/A N.C.R. 1.5. Sample calculation Where relevant, the following sample calculation is provided: Field strength level (㏈㎶/m) = Measured level (㏈㎶) + Antenna factor (㏈) + Cable loss (㏈) – amplifier gain (㏈) Report Number : F690501/RF-RTL009017 Page: 5 of 21 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.6. Worst case of test configurations In order to check all kinds of possible configurations, EUT was evaluated with appropriate client and under each charging condition as below table. EUT configuration Description Charging Mode with client device (Galaxy Note 4 : SM-N920U FCC ID : A3LSMN910U) Less than 1 % of battery Less than 50 % of battery 100 % full charging of battery 1.7. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15 Subpart C §15.209 Section in FCC Part 15 Subpart C Test Item Result 15.209 15.209(a) Radiated emission, Spurious Emission and Field Strength of Fundamental Complied 2.1049 20 ㏈ Bandwidth Complied 15.207 Transmitter AC Power Line Conducted Emission Complied 1.8. Test Report Revision Revision Report number Date of Issue Description 0 F690501/RF-RTL009017 2015.08.20 Initial Report Number : F690501/RF-RTL009017 Page: 6 of 21 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 2. Field Strength of Fundamental and Spurious Emission 2.1. Test Setup The diagram below shows the test setup that is utilized to make the measurements for emission from 9 ㎑ to 30 ㎒ Emissions. The diagram below shows the test setup that is utilized…

Text truncated - open the document above for the full version.

Test setup photos of EUT 1. Radiated Field strength 1.1. Frequency range: 9 ㎑ ~ 30 ㎒ The photo of Field strength with client device Client device (SM-N910U) 1.2. Frequency range: 30 ㎒ ~ 1 ㎓ The photo of Field strength with client device Client device (SM-N910U) 2. Test Setup Photo of MPE 2.1. 10 ㎝Distance between the edge of the EUT and the center of probe A. E-Field Probe Client device (SM-N910U) B. H-Field Probe Client device (SM-N910U) 3. AC Conducted power line emissions Client device (SM-N910U)