2AD5YBTSP0576Mini Portable Speaker

FCC Caution： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. Modifications not authorized by the manufacturer may void user’s authority to operate this device. 1 LOCATION OF CONTROLS 1. Power ON/OFF Switch 2. DC IN Jack (Micro USB Port, for Charging only) 3. Speaker 4. Decorative LED Lights POWER SOURCE The unit has a built‐in Li‐ion rechargeable battery, recharge it before use it when the battery is drained as follows: 1. Connect the Micro USB Plug from the supplied USB Connection Cable to the Micro USB Port on the unit. 2. Connect the full sized USB Plug from the supplied USB Connection Cable to the USB Port on Computer or USB Charger (Not included). Charging will automatically start.  While charging, the Red Decorative LED Lights on the unit will illuminate. When finished charging, it will turn off.  While charging, you can also play and listen music at the same time. Notes: Your battery will last longer if you’re following these simple guidelines for caring and storing. A. Before first time use (or recharge it when the battery is drained), charge it approximately 2 hours. B. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F). 2 C. Do not charge longer than 24 hours. Excessive charging or running the unit until battery fully drains will damage battery. Battery life will be extended if you keep the battery fully charged. D. Battery life naturally shortens slowly over time. E. The rechargeable battery incorporated in this product is not user replaceable. OPERATION: Bluetooth Pairing: First time use or re‐pairing the unit to a new BT Device, pair as follows: 1. Power on the unit by sliding the Power ON/OFF Switch to ON position. The Color Decorative LED Lights on the unit will illuminate and blink. 2. Power on the external BT Device and enter to BT searching mode. Start pairing following the screen instructions from the external BT Device. When paired, you will hear a sound prompt. 3. If pairing is complete you may now play music with your external BT Device. 4. During playback, use the Controls on the paired BT Device to adjust volume level; pause; skip tracks as usual. 5. When finished listening, slide the POWER ON/OFF Switch to OFF position to shut off the unit. Notes: 1. When the external BT Device searched the unit, our model number “CBH576S” will appear on the display of external BT Device. 2. If while pairing you are asked for a code please try “0000” or “1234”. Normal operation after pairing: 1. Power on the external BT Device and enter to BT playback mode. 2. Power on the unit by slide the Power ON/OFF Switch to ON position. The Color Decorative LED Lights on the unit will illuminate and blink. 3. Wait a few seconds until the unit is automatically paired to the external BT Device with a sound prompt. 4. After pairing is complete you may now play music with your external BT Device. 3 TROUBLESHOOTING Check the following before requesting service: SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION Can’t power on Built‐in battery drained Recharge the built‐in battery as page2 No sound or sound weak Volume level of paired BT device is in low level Rise the volume level of the paired BT device Sound distortion Volume level of the BT paired device too high Reduce the volume level of the paired BT device BT not functioning The external BT Device had NOT paired to the unit Pair the external BT device to the unit as page 3 The external BT device too far from the unit Place the external BT device close to the unit SPECIFICATIONS Power Source Built‐in DC3.7V, 400Mah (1.48WH) rechargeable Li‐ion battery; Recharge by DC 5V through DC IN Jack (Micro USB Port) Impedance of Seakers 3 ohm; 3W Audio Power 1.5W (RMS) BT Version: 5.0 BT Operation Distance: 32 Feet in open area PACKAGE INCLUDES 1. User Manual 2. USB Connection Cable (For charge only) SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE 4

Shenzhen Orderly Electronics Co., Ltd. 2020.7.8 Eurofins MET Labs 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Mini Portable Speaker Trademark: CRAIG, MAGNAVOX, NEWTECH FCC ID: 2AD5YBTSP0576 MODEL : CBH576S/CRAIG, MBH576S/MAGNAVOX, NBH576S/NEWTECH, CMA3652/CRAIG, MMA3652/ MAGNAVOX, NMA3652/NEWTECH, CBH576 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Flora Huang /Manager Contact information / address: 4F, Building 7, Asian Industry Park, Bantian Street, Longgang District, Shenzhen, China 518129

Shenzhen Orderly Electronics Co., Ltd. 2020.7.8 Eurofins MET Labs 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Flora Huang /Manager Contact information / address: 4F, Building 7, Asian Industry Park, Bantian Street, Longgang District, Shenzhen, China 518129

Shenzhen Orderly Electronics Co., Ltd. Model Difference Product Name: Mini Portable Speaker Model Number(s): CBH576S/CRAIG, MBH576S/MAGNAVOX, NBH576S/NEWTECH, CMA3652/CRAIG, MMA3652/ MAGNAVOX, NMA3652/NEWTECH, CBH576 Trademark: CRAIG, MAGNAVOX, NEWTECH All the model are the same circuit and RF module, except model names. Regards Sincerely Client’s signature: Client’s name / title : Flora Huang /Manager Contact information / address: 4F, Building 7, Asian Industry Park, Bantian Street, Longgang District, Shenzhen, China 518129

External Photos

40*20mm Label Location FCC ID: 2AD5YBTSP0576 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interfer ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Internal Photos Antenna

Shenzhen BCTC Testing Co., Ltd. FCC ID: 2AD5YBTSP0576 Portable device According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB447498 D01 General RF Exposure Guidance V06 The 1-g SAR and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHZ)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f(GHZ) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Modulation Channel Freq. (GHz) Conduct ed power (dBm) Conducte d power (mW) Tune-up power (dBm) Max tune-up power (dBm) Max tune-up power (mW) Distance (mm) Result calculatio n SAR Exclusion threshold SAR test exclusion GFSK2.4022.271.692±13.002.00<50.618473.00YES Pi/4 DQPSK 2.4022.861.932±13.002.00<50.618473.00YES 8DPSK2.4023.312.143±14.002.51<50.778603.00YES Conclusion: For the max result : 0.77860＜3.0, the SAR testing is not required.

Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2006001417E Test Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-007 Ver.：A.0 Page 1 of 68 FCC Part 15C Test Report FCC ID: 2AD5YBTSP0576 Product Name: Mini Portable Speaker Trademark: CRAIG, MAGNAVOX, NEWTECH Model Name : CBH576S/CRAIG MBH576S/MAGNAVOX, NBH576S/NEWTECH, CMA3652/CRAIG, MMA3652/ MAGNAVOX, NMA3652/NEWTECH, CBH576 Prepared For : Shenzhen Orderly Electronics Co., Ltd. Address : 4F, Building 7, Asian Industry Park, Bantian Street, Longgang District, Shenzhen, China 518129 Prepared By : Shenzhen BCTC Testing Co., Ltd. Address : BCTC Building & 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiaotou Community, Fuyong Street, Bao’an District, Shenzhen, China Test Date: Jun. 19, 2020 – Jun. 30, 2020 Date of Report : Jun. 30, 2020 Report No.: BCTC2006001417E Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2006001417E Test Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-007 Ver.：A.0 Page 2 of 68 TEST RESULT CERTIFICATION Applicant’s name ............. : Shenzhen Orderly Electronics Co., Ltd. Address .............................. : 4F, Building 7, Asian Industry Park, Bantian Street, Longgang District, Shenzhen, China 518129 Manufacture's Name ........ : Shenzhen Orderly Electronics Co., Ltd. Address .............................. : 4F, Building 7, Asian Industry Park, Bantian Street, Longgang District, Shenzhen, China 518129 Product description Product name..................... : Mini Portable Speaker Trademark ......................... : CRAIG, MAGNAVOX, NEWTECH Model and/or type reference CBH576S/CRAIG MBH576S/MAGNAVOX, NBH576S/NEWTECH, CMA3652/CRAIG, MMA3652/ MAGNAVOX, NMA3652/NEWTECH, CBH576 Standards ......................... : FCC Part15.247 ANSI C63.10:2013 This device described above has been tested by BCTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of BCTC, this document may be altered or revised by BCTC, personal only, and shall be noted in the revision of the document. Prepared by(Engineer): Cai Fang Zhong Reviewer(Supervisor): Eric Yang Approved(Manager): Zero Zhou Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2006001417E Test Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-007 Ver.：A.0 Page 3 of 68 Table of Contents Test Report Declaration Page 1. TEST SUMMARY ...................................................... 5 2. TEST FACILITY ....................................................... 6 3. MEASUREMENT UNCERTAINTY........................................ 6 4. GENERAL INFORMATION .............................................. 7 4.1 GENERAL DESCRIPTION OF EUT ....................................... 7 4.2 Test Setup Configuration ................................................ 8 4.3 Support Equipment ..................................................... 8 4.4 Channel List ........................................................... 9 4.5 Test Mode ............................................................ 10 5. TEST FACILITY AND TEST INSTRUMENT USED ........................ 11 5.1 Test Facility ........................................................... 11 5.2 Test Instrument Used .................................................. 11 6. CONDUCTED EMISSIONS ............................................. 13 6.1 Block Diagram Of Test Setup ........................................... 13 6.2 Limit ................................................................. 13 6.3 Test procedure ........................................................ 13 6.4 Test Result ........................................................... 15 7. RADIATED EMISSIONS ............................................... 17 7.1 Block Diagram Of Test Setup ........................................... 17 7.2 Limit ................................................................. 18 7.3 Test procedure ........................................................ 18 7.4 Test Result ........................................................... 20 7.5 RADIATED BAND EMISSION MEASUREMENT AND RESTRICTED BANDS OF OPERATION ........................................................... 24 8. CONDUCTED EMISSION .............................................. 27 8.1 Block Diagram Of Test Setup ........................................... 27 8.2 Limit ................................................................. 27 8.3 Test procedure ........................................................ 27 8.4 Test Result ........................................................... 28 9. 20 DB BANDWIDTH .................................................. 37 9.1 Block Diagram Of Test Setup ........................................... 37 9.2 Limit ................................................................. 37 9.3 Test procedure ........................................................ 37 9.4 Test Result ........................................................... 38 10. MAXIMUM PEAK OUTPUT POWER .................................... 43 10.1 Block Diagram Of Test Setup .......................................... 43 10.2 Limit ................................................................ 43 10.3 Test procedure ....................................................... 43 10.4 Test Result .......................................................... 44 11. HOPPING CHANNEL SEPARATION .................................... 49 11.1 Block Diagram Of Test Setup .......................................... 49 Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2006001417E Test Report Tel: 400-788-9558 Web: https://www.bctc-lab.com BCTC/RF-EMC-007 Ver.：A.0 Page 4 of 68 11.2 Limit ................................................................ 49 11.3 Test procedure ....................................................... 49 11.4 Te…

Text truncated - open the document above for the full version.

Shenzhen BCTC Testing Co., Ltd. Conducted Measurement Photos Shenzhen BCTC Testing Co., Ltd. Radiated Measurement Photos