2AD6M-AX51AX51 Anywhere Network Node

Copyright © 2023 Anywhere Networks by P2 Mobile Technologies Limited. All Rights Reserved. AX50 Series QUICK START GUIDE Applicable for Models AX51, AX52 and AX52e PUBLISHED SEP 1, 2023 REV 1.3 ANYWHERE NETWORKS - 2 - 1. SAFETY INSTRUCTIONS a. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment, or pose a fire hazard if the limitations are not followed. b. Read the instructions before you connect the system to its power source. c. This product must be connected to an IEC60950 compliant limited power source. d. Installation of the equipment must comply with local and national electrical codes. e. This product relies on the building’s installation for short-circuit (overcurrent) protection. f. Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. g. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury and death. h. To comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. i. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. Warning: Do not use this product in a location that can be submerged by water. Warning: Stay off this product during an electrical storm to avoid electrical shock. Warning: Do not touch the device surface during operation due to high temperature. 2. COMPLIANCE FCC marking and the FCC ID on this product represent the product in compliance with part 15 of the FCC regulations and approved by the Federal Communications Commission. The product is to be sold within and outside the US. CE marking on this product represents the product in compliance with health, safety, and environmental protection standards in the radio equipment directives 2014/53/EU under European Commission and the product is to be sold within and outside the European Economic Area (EEA). Warning: The 5.15 to 5.35 GHz band is restricted for indoor use in the above EEA countries. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ⚫ Reorient or relocate the receiving antenna. ⚫ Increase the separation between the equipment and receiver. ⚫ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ⚫ Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications not expressly approved by AX51 Anywhere Network Node for compliance could void the user's authority to operate this equipment. RF Exposure This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” - 3 - CMIIT ID 本产品上如有无线电发射设备型号核准代码表示产品符合《中华人民共和国无线电管理 条例》，并获国家无线电管理委员会核发“无线电发射设备型号核准证”。 OFCA This product in compliance the HKCA 1039 (Issue 6) standards issued by the Hong Kong Communications Authority. Warning: The 5.15 to 5.35 GHz band is restricted for indoor use in Hong Kong. RCM marking on this product represents the product in compliance with AS/NZS 4268 as regulated by Australian Communications and Media Authority (ACMA). KC marking on this product, if any, represents the product in compliance with the clause 2, Article 58-2 of Radio Waves Act in Korea. NCC marking and the NCC certificate number on this product, if any, represent the product in compliance with the LP0002 (4.7) Low-power Radio-frequency Devices technical regulations and approved by the National Communications Commission in Taiwan. Warning: Deployment in Taiwan shall meet NCC requirements below. 警告 • 應避免影響附近雷達系統之操作。 • 高增益指向性天線只得應用於固定式點對點系統。 • 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變 更頻率、加大功率或變更原設計之特性及功能。 • 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時， 應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作 業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射 性電機設備之干擾。 • 電磁波曝露量MPE標準值為：1 mW/cm 2 ，送測產品實測值為：0.14 mW/cm 2 。 The RoHS, China RoHS and WEEE markings on this product represent the product is designed to meet EU Restriction on Hazardous Substances Directive 2011/65/EC, China environmental declaration with Environment-Friendly Use Period (EFUP), and the Directive 2002/96EC on Waste of Electrical and Electronic Equipment respectively. - 4 - 3. QUICK START GUIDE 3.1 PACKING LIST AX51 AX52 AX52e AX51, AX52 or AX52e Anywhere Network Node x 1 Mounting kit x 1…

Text truncated - open the document above for the full version.

< P2 Mobile Technologies Limited > Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023/09/06 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing and Part 2.911(d)(5)(ii) Filing FCC ID: 2AD6M-AX51 1. P2 Mobile Technologies Limited (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. P2 Mobile Technologies Limited (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries of affiliates) as an entity producing “covered” equipment. Sincerely, ________________ Name: Simon Yeung Email: [email protected] Date: 2023/08/22

< P2 Mobile Technologies Limited > Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023‐09‐13 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AD6M‐AX52 Applicant FRN: 0024264327 P2 Mobile Technologies Limited (“the applicant”) certifies that, as of the date of the filing of the application, FCC US Agent, LLC is our designated U.S. agent for service of process for the above referenced FCC ID. P2 Mobile Technologies Limited accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission‐related proceeding involving the equipment. FCC US Agent, LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708‐571‐3148 Email: [email protected] Sincerely, P2 Mobile Technologies Limited FCC US Agent, LLC Simon Yeung Tim Payne [Applicant signature] [U.S.Agent signature]

P2 Mobile Technologies Limited Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: 2AD6M-AX51 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: 1. Block Diagram 2. Schematics 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, _________________ Name: Simon Yeung Email: [email protected] Date: 2023/09/06

P2 Mobile Technologies Limited Declaration of Authorization We Name: P2 Mobile Technologies Limited Address: Unit D5, 19/F, TML Tower, 3 Hoi Shing Road, Tsuen Wan, New Territories, Hong Kong Declare that: Name Representative of agent: Marlin Chen Agent Company name: MRT Technology (Suzhou) Co., Ltd Address: D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone City: Suzhou Country: China is authorized to apply for Certification of the following product(s): Product: AX51 Anywhere Network Node FCC ID: 2AD6M-AX51 Model No.: AX51 Sincerely, ________________ Name: Simon Yeung Email: [email protected] Date: 2023/09/06

P2 Mobile Technologies Limited Declaration of Conformity Federal Communications Commission Authorization and Evaluation Division F F C C C C I I D D : : 2 2 A A D D 6 6 M M - - A A X X 5 5 1 1 Please be notified that we, the undersigned, P P 2 2 M M o o b b i i l l e e T T e e c c h h n n o o l l o o g g i i e e s s L L i i m m i i t t e e d d declares that the product which bears the above FCC ID is also compliant with the FCC requirements for sDOC. And the sDOC procedure shall be carried out prior to marketing the device in the US. Sincerely, _________________ Name: Simon Yeung Email: [email protected] Date: 2023/09/06

P2 Mobile Technologies Limited Test Data Reuse Letter Per FCC KDB 484596 D01 Referencing Test Data v01, this application is intended to reuse previous test data (from FCC ID: 2AD6M-AX52), due to the fact that the two models of products are hardware-wise identical and only the following changes have been made: AX51 (FCC ID: 2AD6M-AX51) based on AX52 (FCC ID: 2AD6M-AX52) to remove the Radio 1 Wi-Fi module. All the other HW & SW are same as the AX52 (FCC ID: 2AD6M-AX52). Therefore, based on this difference, the following spot check testing is made: Test Item Reuse Data Description 26dB Bandwidth Refer to AX52 (FCC ID: 2AD6M-AX52) 6dB Bandwidth Refer to AX52 (FCC ID: 2AD6M-AX52) Maximum Conducted Output Power Refer to AX52 (FCC ID: 2AD6M-AX52) Peak Power Spectral Density Refer to AX52 (FCC ID: 2AD6M-AX52) Frequency Stability Refer to AX52 (FCC ID: 2AD6M-AX52) Radiated Spurious Emissions Make Spot Check Radiated Band Edge Make Spot Check Also, both the referenced application and this new application are all subject to the same FCC rule and there is no new rule update for related rules. Accordingly, we believe that the reuse data from previous certified filing is justifiable. Thank you for your attention and please feel free to contact us, if you should have any questions. Sincerely yours, ________________ Name: Simon Yeung Email: [email protected] Date: 2023/09/06

P2 Mobile Technologies Limited Unit D5, 19/F, TML Tower, 2 Hoi Shing Road, Tsuen Wan, New Territories, Hong Kong Page 1 of 1 SDR (Software Defined Radio) Cover Letter Date:2023-09-19 Refer to KDB 442812 D01 SDR apps Guide v02r03. The following six questions can be used for determining if a radio can elect to be, or must be an SDR. 1. Can the RF parameters of the device be altered through software? Yes - go to 2. No, not an SDR YES 2. Can third parties not permitted by the Commission through specific filings modify, configure, or load different software, or make configuration settings to operate the device or host hardware radio frequency parameters (frequency range, modulation type, maximum output power or other radio parameters) in any other way than granted (or expected to be granted)? Yes, must be an SDR. No - go to 3. No 3. Is the device capable of operating in any other way than granted, or will be, granted? Yes, - go to 4. No - go to 5. No 4. Is this a Part 15 client Device as defined in Section 15.202 (as opposed to a master device)? Yes, qualifies as a part 15 client devices - go to 5. No, must be an SDR. YES 5. Does the manufacturer elect SDR? Yes, elects to be an SDR. No, Not an SDR No Final conclusion: According to the above questions reply, we can confirm this device (FCC ID: 2AD6M-AX51) must be a Non-SDR. _________________ Name: Simon Yeung Email: [email protected] Date: 2023/09/19

Report No.: 2305RSU021-UE 1 of 4 EUT Photograph (1) EUT Photo (2) EUT Photo Report No.: 2305RSU021-UE 2 of 4 (3) EUT Photo (4) EUT Photo Report No.: 2305RSU021-UE 3 of 4 (5) EUT Photo (6) EUT Photo Report No.: 2305RSU021-UE 4 of 4 (7) EUT Photo

AX52 AX52e AX51 AX5x Series Product Line Labels 2023/09/05 Product label Material：White Polyester(白色聚酯薄膜) Dimensions：65mm x30mm AX52 AX52e AX5x Series Product Line Labels 2023/09/05 Unit box label AX51 Material：White Polyester(白色聚酯薄膜) Dimensions：47mm x27mm AX52 AX52e AX5x Series Product Line Labels 2023/09/05 Carton box label AX51 Material：ART Paper(雪銅紙) Dimensions：100mm x100mm

Label Location

Report No.: 2305RSU021-UE 1 of 6 EUT Photograph (1) EUT Photo (2) EUT Photo Report No.: 2305RSU021-UE 2 of 6 (3) EUT Photo (4) EUT Photo Report No.: 2305RSU021-UE 3 of 6 (5) EUT Photo (6) EUT Photo Report No.: 2305RSU021-UE 4 of 6 (7) EUT Photo (8) EUT Photo Report No.: 2305RSU021-UE 5 of 6 (9) EUT Photo (10) EUT Photo Report No.: 2305RSU021-UE 6 of 6 (11) EUT Photo (12) EUT Photo

MRT Technology (Suzhou) Co., Ltd Report No.: 2305RSU021-U3 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 2023-09-13 Template Version:0.0 1 of 11 RF Exposure Evaluation Declaration FCC ID: 2AD6M-AX51 Applicant: P2 Mobile Technologies Limited Product: AX51 Anywhere Network Node Model No.: AX51 Brand Name: Anywhere Networks FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): FCC Part 2.1091 Evaluated Date: 2023-09-05 Result: Complies Reviewed By: Sunny Sun Approved By: Robin Wu The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2305RSU021-U3 2 of 11 Revision History Report No. Version Description Issue Date Note 2305RSU021-U3 V01 Initial Report 2023-09-13 Valid Report No.: 2305RSU021-U3 3 of 11 CONTENTS Description Page 1. General Information ................................................................................................................................ 4 1.1. Applicant ........................................................................................................................................ 4 1.2. Manufacturer ................................................................................................................................. 4 1.3. Testing Facility ............................................................................................................................... 4 1.4. Product Information ....................................................................................................................... 5 1.5. Antenna Details ............................................................................................................................. 5 1.6. Device Classification ..................................................................................................................... 5 1.7. Applied Standards ......................................................................................................................... 6 2. RF Exposure Evaluation ......................................................................................................................... 7 2.1. Test Limits ..................................................................................................................................... 7 2.2. MPE Exemptions ........................................................................................................................... 8 2.3. Calculated Result ......................................................................................................................... 11 Report No.: 2305RSU021-U3 4 of 11 1. General Information 1.1. Applicant P2 Mobile Technologies Limited Unit D5, 19th Floor, TML Tower, No. 3, Hoi Shing Road, Tsuen Wan, New Territories, Hong Kong 1.2. Manufacturer P2 Mobile Technologies Limited Unit D5, 19th Floor, TML Tower, No. 3, Hoi Shing Road, Tsuen Wan, New Territories, Hong Kong 1.3. Testing Facility Test Site – MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 VCCI: R-20025 G-20034 C-20020 T-20020 R-20141 G-20134 C-20103 T-20104 Test Site – MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 CNAS: L10551 FCC: CN1284 ISED: CN0105 Test Site – MRT Taiwan Laboratory Laboratory Location (Taiwan) No. 38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Laboratory Accreditations TAF: 3261 FCC: 291082, TW3261 ISED: TW3261 Report No.: 2305RSU021-U3 5 of 11 1.4. Product Information Product Name AX51 Anywhere Network Node Model No. AX51 EUT Identification No. 20230509Sample#01(For Conducted Testing) 20230803Sample#03(For Radiated Testing) Wi-Fi Specification 802.11a/b/g/n/ac/ax Antenna Specification Refer to Clause 1.7 Operating Temp. -35~60°C Notes: 1. The information of EUT was provided by the manufacturer, and the accuracy of the information shall be the responsibility of the manufacturer. 2. Due to the same modular and antenna between AX51 and AX52, we use all testing data of AX52. 1.5. Antenna Details Antenna Type Frequency Band (MHz) Antenna Gain (dBi) Directional Gain (dBi) Ant 0 Ant 1 Wi-Fi (2*2 MIMO) Panel Antenna 5150 ~ 5850 17 17 17 Remark: 1. The 17dBi panel antenna is the internal panel antenna. 2. Due to all antennas belong to Cross-Polarized Antenna, so for power and power spectral density (PSD) measurements, Directional Gain = Antenna Gain. 3. The EUT supports Cyclic Delay Diversity (CDD) mode on 802.11a/n/ac/ax. 4. The EUT also supports Beam Forming mode on 802.11n/ac/ax, not include 802.11a. Manufacturer automatically backs power down based on a 10log(N) factor based on CDD power. 1.6. Device Classification According to the user manual, the antenna of this device is at least 20cm away from the body of the user, this device is classified as a Mobile Device. So, the RF exposure evaluation requirements of § 2.1091 for mobile device exposure conditions subject to MPE limits. Report No.: 2305RSU021-U3 6 of 11 1.7. Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: ⚫ FCC Part 2.1091 & KDB 447498 D04 Interim General RF Exposure Guidance v01 Report No.: 2305RSU021-U3 7 of 11 2. RF Exposure Evaluation 2.1. Test Limits According to FCC §1.1310: The criteria list…

Text truncated - open the document above for the full version.

MRT Technology (Suzhou) Co., Ltd Report No.: 2305RSU021-U2 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 2023-09-13 Template Version:0.0 1 of 302 RF MEASUREMENT REPORT FCC ID: 2AD6M-AX51 Applicant: P2 Mobile Technologies Limited Product: AX51 Anywhere Network Node Model No.: AX51 Brand Name: Anywhere Networks FCC Classification: Unlicensed National Information Infrastructure (NII) FCC Rule Part(s): Part 15 Subpart E (Section 15.407) Result: Complies Received Date: 2023-05-09 Test Date: 2023-05-24 ~ 2023-09-05 Reviewed By: Sunny Sun Approved By: Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB789033. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2305RSU021-U2 2 of 302 Revision History Report No. Version Description Issue Date Note 2305RSU021-U2 V01 Initial Report 2023-09-13 Valid Note: AX51 removes the Radio 1 Wi-Fi module on the basis of AX52 hardware, therefore, AX51 reuses AX52 (MRT Report: 2305RSU022-U2, FCC ID: 2AD6M-AX52) test data and make spot check with Radiated Spurious Emission & Band Edge. Report No.: 2305RSU021-U2 3 of 302 CONTENTS Description Page 1. General Information ................................................................................................................................ 6 1.1. Applicant ..................................................................................................................................... 6 1.2. Manufacturer............................................................................................................................... 6 1.3. Testing Facility ............................................................................................................................ 6 1.4. Product Information .................................................................................................................... 7 1.5. Radio Specification under Test ................................................................................................... 7 1.6. Working Frequencies .................................................................................................................. 8 1.7. Antenna Details .......................................................................................................................... 9 2. Test Configuration ................................................................................................................................. 10 2.1. Test Mode ................................................................................................................................. 10 2.2. Test System Connection Diagram ............................................................................................. 11 2.3. Test Software ............................................................................................................................. 11 2.4. Applied Standards .................................................................................................................... 12 2.5. Test Environment Condition ...................................................................................................... 12 3. Antenna Requirements ......................................................................................................................... 13 4. Measuring Instrument ........................................................................................................................... 14 5. Decision Rules and Measurement Uncertainty .................................................................................. 16 5.1. Decision Rules .......................................................................................................................... 16 5.2. Measurement Uncertainty ........................................................................................................ 16 6. Test Result .............................................................................................................................................. 17 6.1. Summary .................................................................................................................................. 17 6.2. 26dB & 99% Bandwidth Measurement ..................................................................................... 18 6.2.1. Test Limit ................................................................................................................................... 18 6.2.2. Test Procedure ......................................................................................................................... 18 6.2.3. Test Setting ............................................................................................................................... 18 6.2.4. Test Setup ................................................................................................................................. 18 6.2.5. Test Result ................................................................................................................................ 19 6.3. 6dB Bandwidth Measurement .................................................................................................. 20 6.3.1. Test Limit ................................................................................................................................... 20 6.3.2. Test Procedure ......................................................................................................................... 20 6.3.3. Test Setting .........................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: 2305RSU021-U2 57 of 302 802.11a 6dB Bandwidth Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) Report No.: 2305RSU021-U2 58 of 302 802.11ac-VHT20 6dB Bandwidth Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 802.11ac-VHT40 6dB Bandwidth Channel 151 (5755MHz) Channel 159 (5795MHz) Report No.: 2305RSU021-U2 59 of 302 802.11ac-VHT80 6dB Bandwidth Channel 155 (5775MHz) Report No.: 2305RSU021-U2 60 of 302 802.11ax-HE20 6dB Bandwidth Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 802.11ax-HE40 6dB Bandwidth Channel 151 (5755MHz) Channel 159 (5795MHz) Report No.: 2305RSU021-U2 61 of 302 802.11ax-HE80 6dB Bandwidth Channel 155 (5775MHz) Report No.: 2305RSU021-U2 62 of 302 A.4 Output Power Test Result Test Site SIP-TR1 Test Engineer Alisa Deng Test Date 2023-05-24~2023-08-31 Test Mode Data Rate MCS Channel No. Freq. (MHz) Average Power (dBm) Total Average Power (dBm) Average Power Limit (dBm) Ant 0 Ant 1 11a 6Mbps 36 5180 15.68 14.65 18.21 ≤ 19.00 11a 6Mbps 44 5220 14.59 14.97 17.79 ≤ 19.00 11a 6Mbps 48 5240 14.26 14.61 17.45 ≤ 19.00 11a 6Mbps 52 5260 7.48 7.81 10.66 ≤ 12.92 11a 6Mbps 60 5300 7.82 8.12 10.98 ≤ 12.92 11a 6Mbps 64 5320 7.73 8.33 11.05 ≤ 12.92 11a 6Mbps 100 5500 7.98 7.41 10.71 ≤ 12.92 11a 6Mbps 116 5580 8.28 7.48 10.91 ≤ 12.92 11a 6Mbps 140 5700 8.17 8.04 11.12 ≤ 12.92 11a 6Mbps 144 5720 7.97 7.01 10.53 ≤ 11.83 11a 6Mbps 149 5745 16.39 15.31 18.89 ≤ 19.00 11a 6Mbps 157 5785 16.23 15.43 18.86 ≤ 19.00 11a 6Mbps 165 5825 15.68 15.11 18.41 ≤ 19.00 11ac-VHT20 MCS3 36 5180 11.02 11.82 14.45 ≤ 19.00 11ac-VHT20 MCS3 44 5220 14.59 14.86 17.74 ≤ 19.00 11ac-VHT20 MCS3 48 5240 14.15 14.54 17.36 ≤ 19.00 11ac-VHT20 MCS3 52 5260 7.76 7.99 10.89 ≤ 12.93 11ac-VHT20 MCS3 60 5300 7.72 8.05 10.90 ≤ 12.93 11ac-VHT20 MCS3 64 5320 7.60 8.09 10.86 ≤ 12.93 11ac-VHT20 MCS3 100 5500 8.18 7.76 10.99 ≤ 12.93 11ac-VHT20 MCS3 116 5580 8.11 7.57 10.86 ≤ 12.93 11ac-VHT20 MCS3 140 5700 7.88 6.61 10.30 ≤ 12.93 11ac-VHT20 MCS3 144 5720 7.76 6.71 10.28 ≤ 11.77 11ac-VHT20 MCS3 149 5745 15.56 15.44 18.51 ≤ 19.00 11ac-VHT20 MCS3 157 5785 15.76 15.56 18.67 ≤ 19.00 11ac-VHT20 MCS3 165 5825 14.99 15.52 18.27 ≤ 19.00 Report No.: 2305RSU021-U2 63 of 302 Test Mode Data Rate MCS Channel No. Freq. (MHz) Average Power (dBm) Total Average Power (dBm) Average Power Limit (dBm) Ant 0 Ant 1 11ac-VHT40 MCS2 38 5190 12.68 13.67 16.21 ≤ 19.00 11ac-VHT40 MCS2 46 5230 15.69 16.04 18.88 ≤ 19.00 11ac-VHT40 MCS2 54 5270 9.18 10.03 12.64 ≤ 12.98 11ac-VHT40 MCS2 62 5310 8.98 10.12 12.60 ≤ 12.98 11ac-VHT40 MCS2 102 5510 9.83 9.64 12.75 ≤ 12.98 11ac-VHT40 MCS2 110 5550 9.51 9.39 12.46 ≤ 12.98 11ac-VHT40 MCS2 134 5670 9.37 9.67 12.53 ≤ 12.98 11ac-VHT40 MCS2 142 5710 9.40 9.71 12.57 ≤ 12.98 11ac-VHT40 MCS2 151 5755 15.68 15.46 18.58 ≤ 19.00 11ac-VHT40 MCS2 159 5795 15.72 15.82 18.78 ≤ 19.00 11ac-VHT80 MCS4 42 5210 14.69 15.56 18.16 ≤ 19.00 11ac-VHT80 MCS4 58 5290 8.83 10.32 12.65 ≤ 12.98 11ac-VHT80 MCS4 106 5530 9.22 9.57 12.41 ≤ 12.98 11ac-VHT80 MCS4 122 5610 9.52 9.38 12.46 ≤ 12.98 11ac-VHT80 MCS4 138 5690 9.42 10.01 12.74 ≤ 12.98 11ac-VHT80 MCS4 155 5775 15.77 15.13 18.47 ≤ 19.00 11ax-HE20 MCS1 36 5180 15.34 14.31 17.87 ≤ 19.00 11ax-HE20 MCS1 44 5220 14.46 14.69 17.59 ≤ 19.00 11ax-HE20 MCS1 48 5240 13.97 14.06 17.03 ≤ 19.00 11ax-HE20 MCS1 52 5260 8.06 8.21 11.15 ≤ 12.98 11ax-HE20 MCS1 60 5300 8.01 7.99 11.01 ≤ 12.98 11ax-HE20 MCS1 64 5320 7.72 8.25 11.00 ≤ 12.98 11ax-HE20 MCS1 100 5500 8.34 8.28 11.32 ≤ 12.98 11ax-HE20 MCS1 116 5580 8.56 7.97 11.29 ≤ 12.98 11ax-HE20 MCS1 140 5700 8.06 8.31 11.20 ≤ 12.98 11ax-HE20 MCS1 144 5720 8.08 8.15 11.13 ≤ 11.91 11ax-HE20 MCS1 149 5745 15.91 15.67 18.80 ≤ 19.00 11ax-HE20 MCS1 157 5785 15.73 15.31 18.54 ≤ 19.00 11ax-HE20 MCS1 165 5825 15.43 15.82 18.64 ≤ 19.00 Report No.: 2305RSU…

Text truncated - open the document above for the full version.